V-tech Go! Go! Smart Wheels Revved Up Raceway Assembly Instructions

Parent’s Guide
Revved Up Raceway™
91-003714-000

2
2
2
INTRODUCTION
Thank you for purchasing the Go! Go! Smart Wheels®Revved Up
Raceway™!
Get ready to flip, jump and spin with the Go! Go! Smart Wheels® Revved
Up Raceway™. This interactive raceway features two levels of pretend
play and learning fun! Place Rocco the Race Car on the second level
platform and choose the launch ramp or the bumpy off-road ramp. Raise
the gate to send him sliding down to the roundabout for whirling, twirling
fun. After Rocco visits the repair deck, raise the lever to launch him back
onto the roundabout. Then turn the handle to spin the roundabout and
send Rocco on a dizzy ride!
SmartPoint®
Race Car
Repair Deck

3
3
3
INCLUDED IN THIS PACKAGE
One gallery
One SmartPoint®
Race Car
One racing platform
Gate BGate A Two platform
supports
One road block One jump track
One sign post,
One flipping sign
One repair deck
NOTE: This toy is not intended for teething.
One handle
One bumpy track
One lever

4
4
4
One label sheet
One base supportOne base
(with roundabout)
One adapter
Three screws
One parent’s guide

5
5
5
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains
important information.
ATTENTION :
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE : Il est conseillé de conserver ce guide des parents car il
comporte des informations importantes.
Adult assembly required.
Ce jouet doit être assemblé par un adulte.
Unlock the packaging locks:
Turn the packaging lock counterclockwise
several times.
Pull out and discard the packaging lock.

6
6
6
GETTING STARTED
BATTERY INSTALLATION
Race Car
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom
of the Race Car. Use a coin or a
screwdriver to loosen the screw.
3. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new
alkaline batteries is recommended
for maximum performance.)
4. Replace the battery cover and tighten
the screw to secure the battery cover.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

7
7
7
LABEL APPLICATION
Please adhere the labels to the playset securely as
indicated on the following pages:
1
2
7
6
4
5

8
8
8
812
13 18
10
22 21
11
14
16
15
17
20
9

9
9
9
ASSEMBLY INSTRUCTIONS
Revved Up Raceway™
With the Go! Go! Smart Wheels®Revved Up Raceway™, safety
comes first.To ensure your child’s safety, adult assembly is required.
1. Place the Racing Platform right-side up and insert the Gallery,
Gate A and Gate B. Next insert the two Platform Supports into
the slots underneath the Racing Platform, as shown below. You
will hear a “click” sound to indicate the pieces are secure.
Note: Once the Gallery is attached, it cannot be removed.
2. With the Jump Track right-side up, insert the Road Block through
the slot on the Jump Track. Then attach the Jump Track and the
Bumpy Track to the Racing Platform, as shown below.

10
10
10
3. Next, assemble and attach the base components following the
stepsbelow:
A. With the Base and the Repair Deck upside down, attach the
Repair Deck to the Base, insert the Base Support as shown
and tighten the three Screws to secure it to the unit, as shown
below.
B. Turn the Base right-side up, lift the Repair Deck and insert the
Lever into its Base, as shown below.