VABCHES D8L235BR01 User manual

1-24
D8L235BR01
As this item contains many parts, please read the installation
instruction carefully before installation and complete the
installation with the cooperation of your partner. Please use
tools properly and carefully. If you have any questions about
the product and installation, please contact us.
Our professional after-sales team will serve you online all
[e-mail]
day.
WhatsApp community↑

Before You Start
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware of to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
Helpful Hints
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with an R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
PEOPLE NEEDED FOR ASSEMBLY: 1-2
2-24

Board Identification
Not actual size
TOP
Qty:1
A
LEFT PARTITION
Qty:1
C
BOTTOM
Qty:1
3-24
B
RIGHT PARTITION
Qty:1
D
WINE BOTTLE RACK PLATE
Qty:4
F
FIXED SHELF
Qty:4
E
WINE BOTTLE RACK PLATE
Qty:2
G
DOOR
Qty:2
I
WINE BOTTLE RACK PLATE
Qty:2
H

Board Identification
Not actual size
BACK PANEL
Qty:1
J
RIGHT FRAME
Qty:1
L
LEFT FRAME
Qty:1
4-24
K
WINE CUP HOLDER
Qty:2
M
REAR WINE BOTTLE RACK
Qty:2
O
FRONT WINE BOTTLE RACK
Qty:2
N
FOOT
Qty:2
P
DECORATIVE ANGLE IRON
Qty:2
R
DECORATIVE IRON SHEET
Qty:2
Q
MIDDLE SHELF
Qty:1
S

Board Identification
Not actual size
5-24
A
K
B
C
D
E
E
E
E
FF
G
H
H
G
F
F
I
I
P
J
J
L
M
N
O
N
O
P
Q
R
R
S
Q

Part List
Ø15X11mm
1
CAM LOCK
spare:2
X16
6-24
Ø6.5X35mm
2
CAM BOLT
spare:2
X16
Ø8X30mm
3
WOOD DOWEL
spare:2
X20
Ø6.3X40mm
4
SCREW
spare:1
X10
Ø3.5X14mm
5
SCREW
spare:2
X30
Ø3X14mm
6
SCREW
spare:2
X16
M6X20mm
7
SCREW
spare:2
X14
M6X30mm
8
SCREW
spare:1
X8
M4X20mm
9
SCREW
spare:1
X4
Ø4X14mm
X4
186X37X26mm
X2
DOOR HINGE
X4
SCREW
spare:1
HANDLE
Ø35mm
10 11 12
15X12X12mm
13
GLASS CLIP
X4
30X20X10mm
X1 X1 set
HEX KEY
X1
STOPPER LAMP TUBE
4X65mm
14 15 16

7-24
Part List
WRENCH
X1
TIPPING RESTRAINT
HARDWARE KIT
X1 set
SCREW:Ø3.5*14
SCREW:Ø3.2*30
1817
Ø10mm
10#
Cam Lock
Fastening
System
Insert the cam bolt into the
hole first, then insert the
cam lock and lock it.
1
3
2
4
The opening must point toward the
edge of the board
LAMP CLIP
X6
19
LAMP LINE BUCKLE
X3
20
Ø17X15X10mm 19X14X9mm

STEP1
8-24
X16
3
Ø8X30mm
2
X8
2
Ø6.5X35mm
E
C
D
2
3
E X 4

STEP2
9-24
X4
2X4 1
Ø6.5X35mm
Proper orientation of CAM LOCK
UNLOCK
LOCK
B
2
D
C
1
Ø15X11mm
B
The raw edge is aligned with
the direction of the hole

STEP3
10-24
X8
1
Ø15X11mm
Proper orientation of CAM LOCK
UNLOCK
LOCK
B
P
PC
D
E
E
E
E
1

STEP4
11-24
X8
4
B
K
L
4
Ø6.3X40mm
X4
8
M6X30mm
8
M6*30mm
Before you install this screw, please
make sure the screw size is M6*30mm
D
E
E
E
E
X1
16
4X65mm

STEP5
12-24
X4
2
Ø6.5X35mm
2
X1
14
30X20X10mm
X2
6
Ø3X14mm
X6
5
Ø3.5X14mm
6
14
A
5
19
A
X6
19
17X15X10mm

STEP6
13-24
X4
10
Ø4X14mm
A
A
10
M
M
15
15
X1 set
15
First stick the back of the
crimping device to the
surface of the panel. Then
clip the light line into the
crimping device
Note: please remove the
protective film on the surface of
the lamp before installing the
lamp.
X2
20
20
19X14X9mm

STEP7
14-24
X4
Ø15X11mm
1
1
8
M6*30mm
Before you install this screw, please
make sure the screw size is M6*30mm
X4
M6X30mm
8X1
4X65mm
16
A
Face forward here
Face forward here
B
K
L
Proper orientation of CAM LOCK
UNLOCK
LOCK

STEP8
15-24
X14
M6X20mm
7
A
28mm
43mm
X1
Ø10mm
17
10#
7
17
Q
R
R
Q
Q

STEP9
16-24
X14
Ø3X14mm
6
Before attaching the back panel,
be sure that the unit is at 90°.
90°
J
J
J
J
A
A
Stick the back of the crimping device
to the back of the metal frame
X1
20
19X14X9mm
20

STEP10
17-24
X4
13
15X12X12mm
S
First push the glass plate along the clip in parallel, and then tighten the
lower screw clockwise as shown in the figure.
Tighten with a cross screwdriver.
13

STEP11
18-24
X24
5X4 12 X4 9
II X 2
5
12
9
11
Ø3.5X14mm Ø35mm
X2
11
186X37X26mm M4X20mm
12
5
I
I

A
A
C
B
To adjust depth.
Loosen screw "B" and adjust door, if the door can
not be adjusted, please loosen screw "C", then try
again. Tighten screw "B" and "C".
To adjust side ways.
Turning the screw "C" on BOTH hinges on each
door.
To adjust the vertical height.
Loosen the four screws "A" on both hinges.
Two of them are usually in slotted holes which
allows you to adjust up or down by a few mm.
Then tighten back up.
Door
Cabinet
Door
Cabinet
Door
Cabinet
STEP12
19-24

STEP13
20-24
X4
3
Ø8X30mm
X2
4
Ø6.3X40mm
Notch direction
Notch direction
Notch direction
step1 step2
step3 Effect after assembly
Notch direction
Notch direction
4
3
H
G
H
G
F
G
H
F FF
F
G
H
X 2 X 2
X 2 X 2