VABCHES JY9981BS01 User manual

1-38
JY9981BS01/
JY9981HS01
instruction carefully before installation . Please use tools
properly and carefully. If you have any questions about the
product and installation, please contact us.
Our professional after-sales team will serve you online all
[email protected]
day.
OR
As this item contains many parts, please read the installation
WhatsApp community↑

2-38
Before You Start
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer


（Assembly
speed can be increased by using electric screwdriver）
Helpful Hints



- Slides are labeled with an R(right) and L
- Make sure to always face the point on the top of the Cam Lock towards the








PEOPLE NEEDED FOR ASSEMBLY: 1-2

3-38
Board ldentification
Not actual size
1x1 2x1 3x2
4x1 5x4 6x1
7x1 8x1 9x1
x1 x1
10 11 12
x1 x1 x1
13 14 15
x1 x1 x1
16 17 18
x1
Left upper mirror rear panel Upper right rear panel Upper right panel
Upper cover plate Upper side, grating Right table panel
Left small panel Left side panel Left rear upper connecting plate
Remove the horizontal bar Left rear lower connecting bar Lower right rear panel
Lower right front panel Right side panel Right middle extraction slide rail
reinforcement vertical bar
Right middle fixed layer board Right middle fixed layer plate front
reinforcement strip
Lower right base plate

4-38
Board ldentification
Not actual size
x1 x1 x1
19 20 21
x1 x1 x1
22 23 24
x1 x2 x1
25 26 27
x1 x1
28 29
Bottom right floor standing
water
Drawer front panel Drawer left panel
Drawer right panel Drawer back panel Drawer board
Stool cover plate Stool side panel Stool back board
Front plate of stool Stool base plate

Board ldentification
5-38
1
2
3
3
4
5
5
5
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
24
23 22
21
25
26
26
27
29
28

6-38
Part List
Kx1
Handle and Handle
screw
Lx2
L-shaped iron sheet
Mx2
Hinge
Nx22(+2)
Screw
Ox1
Folding bracket
Ø20mm
Px1
Power Supply
Ax45(+2) Bx49(+2) Cx50(+3) Dx23 (+2) Ex16(+1)
Ø6x35mm Ø15x10mm Ø6x30mm Ø4x35mm Ø3x12mm
Cam Bolt Cam Lock Dowel
Flat Head
Tapping Screw Sliding Track Screw
Fx4
Screw
Gx4
Cross Vertical
Romulus
Hx2 Ix24(+2) Jx1
Hole sticker Hair dryer bracket
and screws
Two hole long
iron bar
x1
Q
Power supply socket
x2
R
Ø3.5x12mm
Screw
x2
Sx2
T
Ø6x30mm
Anti-Fall Strip Plastic Expansion
Ux2
Ø4x12mm
Ø6x55mm Ø10x9.5mm
39x22x7mm Ø3.5x12mm
CL x1
L300mm
Sliding Track
x1
L300mm
CR
Sliding Track
x1
DL
L300mm
Sliding Track
x1
DR
L300mm
Sliding Track
Round head screw

7-38
Part List
Cam Lock
Fastening
System



1
3
2
4
The opening must point toward the
edge of the board

8-38
STEP 1
Ax17
Ø6x35mm
12
13
18
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
Proper orientation of CAM LOCK
UNLOCK
LOCK
Cx10
Ø6x30mm
Bx1
Ø15x10mm
18
18
19
19 C
C
C
C
C
C
C
C
C
C
B
A
A
15

9-38
STEP 2
B
B
B
C
C
C
C
Proper orientation of CAM LOCK
UNLOCK
LOCK
12
12
14
14
12
14
19
18
18
19
B
Cx4
Ø6x30mm
Bx4
Ø15x10mm
B
II
I
Ix3
Ø20mm

10-38
STEP 3
Cx8
Ø6x30mm
Bx3
Ø15x10mm
C
C
B
B
B
CC
12
12
16
15
16
16
17
12
CC
17
16
CC
12
Proper orientation of CAM LOCK
UNLOCK
LOCK
BB
II
15
15
Ix2
Ø20mm