VABCHES J4Q000GR01 User manual

J4Q000GR01
1-24
As this item contains many parts, please read the installation
instruction carefully before installation . Please use tools
properly and carefully. If you have any questions about the
product and installation, please contact us.
Our professional after-sales team will serve you online all
[e-mail]
day.

Before You Start
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware of to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw. （Assembly
speed can be increased by using electric screwdriver）
Helpful Hints
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with an R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- If there is a back panel in the package, please install it to make sure your unit is
complete and sturdy.
-Please fix all the screws provided for the back panel which can enhance product
stability. If it is difficult to fix it when tightening, it can be fixed with the help of a
hammer and then tightened.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
PEOPLE NEEDED FOR ASSEMBLY: 1-2
2-24

Board Identification
Not actual size
MIDDLE PANEL
Qty:1
A
RIGHT PANEL
Qty:1
C
LEFT PANEL
Qty:1
3-34
B
FIXED SHELF
Qty:1
D
PARTITION
Qty:2
F
BOTTOM
Qty:1
E
BACK PANEL
Qty:2
G
FRONT TABLE LEG
Qty:2
I
REAR TABLE LEG
Qty:2
H

Board Identification
Not actual size
UPPER SUPPORT TUBE
Qty:2
J
4-34
STORAGE BOX
Qty:1
L
LOWER SUPPORT TUBE
Qty:2
K
BOTTOM
Qty:1
M
Ø15X9.5mm
CAM LOCK
spare:2
X12
Ø6.5X35mm
CAM BOLT
spare:2
X12
Ø8X30mm
WOODEN DOWEL
spare:2
X20
M6X40mm
BOLT
spare:2
X24
Part List
1234

Ø4X40mm
SCREW
spare:1
X8
Ø3.5X14mm
SCREW
spare:1
X2
Ø3X12mm
SCREW
spare:1
X6
PLUG BOARD
X1
（Ø28）M6X20mm
LEVELER
X4
4X65mm
HEX KEY
X11
LAMP TUBE
X1
17X9.5mm
LAMP BELT BUCKLE
X6
ANTI-TIPPING HARDWARE
X1 set
5-24
Part List
5678
9 10 11 12
13
Insert the cam bolt into the hole first, then insert the cam lock and lock it.
13 24
Cam Lock Fastening System
The opening must point toward the
edge of the board
Ø4X30mm
SCREW
spare:1
X2
14

Board Identification
Not actual size
6-24
A
C
B
D
E
F
F
G
G
H
H
I
I
J
J
K
K
L
M

STEP1
7-24
X16
3
Ø8X30mm
G Fx 2 x 2
3
LL
M

STEP2
8-24
Proper orientation of CAM LOCK
UNLOCK
LOCK
X8
2
Ø6.5X35mm
X8
1
Ø15X9.5mm
F
F
G
G
D
2
1
D

STEP3
9-24
X8
5
Ø4X40mm
D
F
G
FG
E
5

STEP4
10-24
X4
9
（Ø28）M6X20mm
x 2
I
H
9
9

STEP5
11-24
X4
4
M6X40mm
K
J
K
J
I
I
The notch is facing up
The notch is facing up
4
X1
10
4X65mm

STEP6
12-24
I
I
E
D
X4
4
M6X40mm
X1
10
4X65mm
4
J
J
K
K
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.

STEP7
13-24
H
H
4
X4
4
M6X40mm
X1
10
4X65mm
E
D
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.
J
J
I
I

STEP8
14-24
X2
14
Ø4X30mm
14
D
E
G
G
H
H

STEP9
15-24
X4
2
Ø6.5X35mm
X4
3
Ø3.5X14mm
X1 set
13
Ø8X30mm
A
A
B
C
2
3
1
UP
X4
1
Ø15X9.5mm
Proper orientation of CAM LOCK
UNLOCK
LOCK
13

X6
7
X1 set
11
7
C
A
B
Ø3X12mm
X6
12
17X9.5mm
12
STEP10
16-24
12
11
11
11
1.先将灯带背面的胶布撕掉.
2.然后将灯带压扣卡住灯带
3.最后对准相应的孔位，拧入螺丝（7），先拧入3/1，将灯带拉直并按压灯带，使
其粘牢在面板上面，最后拧紧所有的螺丝

STEP11
17-24
X12
4
M6X40mm
X1
10
4X65mm
4
Please tighten the screws
to 80% first, and tighten
all screws 100% after all
parts are assembled.
A
C
B
D
E
H
H
I
I

STEP12
18-24
X2
6
Ø3.5X14mm
X1
8
8
6
A
C
B

STEP13
19-24
L
When the ground is uneven, you can
rotate the feet to adjust the height.
Please read the following operating instructions for the use
function of the light belt

X1 set
20-24
1.make mark on
the wall
WALL
2.drill two Ø6
holes on the
wall
WALL
3.put two
anchors in the
holes
1 2 3
5.Push the cabinet close to the wall so
that the two bases are close to each
other, and then put on nylon tie to
tighten it.
Install the tipping
restraint hard ware
4.fix the device on the
wall by the long srews
4
We have included a set of tipping restraint hardware for
this unit. You must install this hardware to prevent
accidents or injuries that can result from the unit falling.
When properly installed, this restraint can provide
protection against the unexpected tipping of the unit due to
small tremors, bumps or climbing. We strongly recommend
mounting this hardware to a wall stud and your unit.
NOTE:The tipping restraint hardware included is for
wooden stud wall construction. It must be attached to a
wall stud. Depending upon your wall construction different
anchor hardware maybe required. Please contact your local
hardware store for assistance. Young children can be
seriously injured by tipping furniture. You must install the
tipping restraint hardware with the unit to prevent the unit
from tipping, causing any accidents or damage. The tipping
restraints are intended only as a deterrent and are not a
substitute for proper adult supervision. The tipping
restraints are not earthquake restraints. If you wish to add
the extra security of earthquake restraints, they must be
purchased and installed separately.
WALL
13
5
STEP14