Vaxcel T0476 Instruction manual

Turn off the power at fuse or circuit box
Installation Steps
Glass Panel
Metal Frame
Iron Plate
Threaded Pipe
1. Unscrew the loop to remove the rubber pad and cover.
2. Unscrew the hex nut and washer from the threaded
pipe to remove the upper cover.
3. Gently place four glass panels into the metal frame,
then press the clips to secure the glass panels. (Fig.1)
Note: The patterned side of faces glass out.
Fig.1
Glass Panel
Clip
Metal
Frame
4. Install a bulb (not included). See relamping label
at socket area or packaging for maximum allowed wattage.
5. Attach the upper cover, washer, hex nut, cover, rubber pad
and loop to the threaded pipe.
6. Pull out the wires and grounding wire from the post.
Make wire connections using the wire connectors (B):
---The black wire from the fixture to the black wire
from the post.
---The white wire from the fixture to the white wire
from the post.
---The grounding wire from the fixture to the grounding
wire from the post.
Carefully put the wires back into the post.
Bulb Type A Max.60W
(not included)
Grounding Wire
Fixture Wire
Wire Connector (B)
Post
Fitter
Photocell
Fitter Screw (A)
Hardware Package (included):
Wire Connector (B)
Fitter Screw (A)
Loop
Rubber Pad
Cover
Washer
Hex Nut
Upper Cover
181220
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
T0476
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Turn on the power at fuse or circuit box
181220
7. Place the fitter on the post, then secure it with the fitter screws (A).
CAUTION: With silicone caulking compound, caulk completely around where the fitter meets with the
post surface to prevent water from seeping into the post.
Turn on the power at fuse or circuit box
1. Turn off the power at the fuse or circuit box before starting installation.
2. Unthread the fitter screw and plate, and then Loosen the wire connectors connected with the
wires from photocell. (See Fig.2)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connectors (B) : (See Fig.3)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
Operation the Unit Without Photocell
Photocell
White Wires From
Photocell
Wire Connector
Wire Connector (B)
Black Wire From
Fixture
Wires From Fixture
Wires From
Main Power
White Pigtail
Pigtail
Red Wires From
Photocell
Black Wires From
Photocell
Fig.2 Fig.3
White Wire From
Fixture
Plate
Fitter Screw
Photocell
Wire Connector
Black Wire From
Fixture
White Pigtail
Fig.2
Plate
Washer
Hex Nut
Assembly Kit
6062MM (1SET)
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Glass Shade
10076W
Wire Connector (B)
Fitter Screw (A)
B
A
A:8"
B:21-1/2"