Ventair FAN0530 User manual

CAUTION
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If any of the supply cords are damaged they must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid possible damage to the system.
• Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-
burning appliances.
• Means for disconnection must be incorporated in the fixed wiring in accordance with AS/NZS wiring rules.
ELECTRICAL CONNECTION
Important Note: Junction Box supplied is suitable for internal use and
below roof installation. (inside of the building)
Cut the Dektite roof flashing on the 150/160 marking and fit to the rigid duct before
commencing. (See separate installation sheet detailing this).
For below roof terminations the motor lead exit hole should be as far down the rigid
duct as is practical – allow enough lead to protrude from the duct as is required for
termination. After fitting the Dektite, drill an 8mm hole at a suitable point in the rigid duct
and fit the supplied rubber grommet .The motor lead can then be passed through the
grommet to the outside of the rigid duct.
The assembly can now be placed in position in the roof penetration per the separate
instruction sheet – “Installation Instructions for Roof Penetrations”. Once the assembly
has been fastened to the roof by the Dektite fastening procedure, the electrical
connections can be made. The junction box can be fastened to the rigid duct if
necessary.
You may find it more convenient to pull the whole assembly down as far as possible in
the Dektite flashing to carry out the terminations. (Fig. 1.) Once completed, the assembly
can then be pushed back up through the Dektite. (Ensure that a visual check is made
above the roof afterwards to check that the Dektite is sealing correctly around the rigid
duct). (Fig. 2.) Once the terminations are completed the rigid duct can then be fastened
to a rafter or purlin with the supplied clamp for rigidity. Ducting connections can then be
made.
Through Roof Fans
Fig 1
Fig 2
Please Note: Junction Box is only supplied with:
FAN0530 / FAN0532 / FAN0534 / FAN0535 / DCT0189 / FAN0740 / FAN0967/FAN1009
INSTALLATION INSTRUCTIONS

PUB0116 1906
Wiring Connections:
For axial ßow induction motor models (no capacitor):
FAN0531/FAN0533/FAN0532/FAN0534/FAN0739/FAN1060/FAN1009/DCT0189
Fasten tube to roof truss or rafter using clamp
bracket supplied. Tube/cowl must be mounted
vertically to ensure weatherprooÞng
Fix diffuser to ceiling and fasten ducting. If screw-Þxing diffuser is
supplied cut 153mm diameter hole. If diffuser is type with spring
loaded self-latching clip fasteners cut 205mm diameter hole.
Make electrical connections below
roof
Flexible ducting connects directly
to the bottom of rigid duct. Cut any
excess length of ducting off before
connecting.
For FAN0967 model (3 speed)
For centrifugal fan models: FAN0529/FAN0530/
FAN0535/FAN0740
Motor
P
N
E
Brown
Blue
Green/Yellow
Red
Blue
Green
P
N
E
2.0 F
CAP
Motor
White
Connect SP3/SP2/SP1 to single
phase (P) for High/ Medium/ Low
speed control
White (5)
SP3/P
SP2/P
SP1/P
N
E
White (3)
White (2)
White (1)
White (4)
Green/Yellow
Motor
2.0 F
CAP White (6)
Violet
SP3/P
SP2/P
SP1/P
N
E
Black
Brown
White
Blue
Green/Yellow
Motor
2.0 F
CAP Grey
For FAN1002 (3 Speed)
Connect SP3/SP2/SP1 to single
phase (P) for High/ Medium/ Low
speed control