Ventair SPYDAEC SPYEC1253WH User manual

SPYEC1253WH
SPYEC1253BL
SPYEC1423WH
SPYEC1423BL
SPYEC1253WH-L
SPYEC1253BL-L
SPYEC1423WH-L
SPYEC1423BL-L
(Actual products and/or parts, may vary slightly in design from the images
depicted in this Manual.)
APP Wi-Fi CONTROL
CCT DimFR
Fan off Light
1H 2H 4H
1
2
3
4
5
6

Thank you for purchasing this quality Ventair ceiling fan.
Please read all instructions carefully to ensure correct installation, and operation.
Note: Keep this manual for future reference.
1. To Ensure a Safe, and successful installation, refer to, and follow, all instructions and diagrams.
2. All electrical work should only commence after disconnection of the power. Remove fuses or turn off the
circuit breaker to ensure all pole isolation of the electrical supply.
3. Make sure that your installation site will not allow the rotating fan blades to come in contact with any object
and that there is a minimum clearance of 300mm from the blade tip to the wall or ceiling. Please note that the
greater the clearance around the fan, the better the airflow will be.
4. The fixing point for the fan must be able to support the weight of 4 times that of the net weight of the fan.
Net weights can be found on the next page. If you are mounting the fan to a ceiling junction box, the box and
fixing must be able to support the moving weight of the fan and must not twist or work loose.
5. The fan must be earthed.
6. It is not recommended that ceiling fans and gas appliances be operated in the same room at the same time.
7. Do not insert anything into the fan blades while the fan is operating. This will damage the blades and upset
the balance of the unit causing the unit to wobble.
8. Once fully installed, double check that all connections are secured and tightened before operating.
9. Because of the fan’s natural movement, some connections may loosen over time. Check the support
connections,brackets and blade attachments twice a year, adjust/gently tighten as necessary.
10. Always have your fan installed by a licensed electrician.
11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
12. Children should be supervised to ensure that they do not play with the appliance.
13. The fan is to be installed so that the blades are at least 2.1m or more above the floor.
This product is suitable for use in Tropical climate areas.
The Fan may be used indoors, covered outdoors and is ideal for commercial applications.
2

10(LED) models
9(No light) models
Unpack the fan and carefully identify the parts.Please refer to Fig1.
NOTE: Check for any damage prior to installation. Any Damage, marks or scratches are not
covered by In-Home warranty and should be returned to place of purchase for a replacement.
SPYEC1253WH
SPYEC1253BL 3.81kg
3.98kg
4.07kg
4.24kg
30 watts
30 watts
38 watts
38 watts
SPYEC1253WH-L
SPYEC1253BL-L
SPYEC1423WH
SPYEC1423BL
SPYEC1423WH-L
SPYEC1423BL-L
20 watts
(TRI COLOUR)
20 watts
(TRI COLOUR)
220-240V
220-240V
220-240V
220-240V
SPECIFICATION
11
9. Fascia
10. LED light panel
11. Motor cover plate
12. Decorative screw cover
6
12
13. Blade screws
Fig 1.
CCT DimFR
Fan off Light
1H 2H 4H
1
2
3
4
5
6
1
2
3
4
5
6
7
8
13
2
2

1. Before installation, make sure that the blade tips will not be within 300mm of any
object or fixture.
2. Using screws provided ,secure the hanging bracket to a ceiling joist or suitable structure
that is capable of supporting at least four times the actual weight of the fan (see Specifications)
Note : For structures that are not Wooden , please use the appropriate fixing screws or
bolts to suit.
3. Connect safety cable to bracket as indicated in fig 2.
FIG 2.
INSTALLING MOUNTING BRACKET
1. Ceiling Joist
2. Canopy
3. Terminal Block and Mounting Plate
4. Earth Wire
5. Hanger Ball
6. Down rod
7. Safety steel wire (to be fixed on the
bracket via the screw)
*Please use the fixing screws provided.
Use of non certified fixing screws may
void the warranty.
INSTALLING BLADES
Slide Lower canopy into position ensuring
it does not touch any spinning part of the fan.
Your fan is now ready to hang.
Slide the 'Lower canopy' upwards and
move 'motor cover plate' to the side.
Motor cover plate
Lower canopy
Slide 'Blades into positon and attach
gently using screws provided.
Clip 'motor cover plate' into position making
sure the tabs cover the blade joints.
Fixing screws
Adjustable Screw
(For Canopy)

WIRING AND ELECTRICAL CONNECTIONS.
Spyda EC with light models
Spyda EC without light models
Do not use any other style/type or brand of speed controller for this Fan.
Each Fan must have A 'localised single pole isolation switch' as
indicated in the diagram.
5
WARINING : FOR YOUR SAFETY, ENSURE THE MAINS SUPPLY IS SWITCHED
OFF TO THE WIRING CIRCUIT BEFORE PERFORMING ANY ELECTRICALTASKS.
Wiring Diagram Fig 6.
BROWN
BLUE
L
N
RED
BLACK
BLUE
GREEN/YELLOW
MOTOR
GREEN/YELLOW
LOCALISED SINGLE
POLE SWITCH DOUBLE SWITCH
BROWN
BLUE
L
N
RED
BLACK
BLUE
GREEN/YELLOW GREEN/YELLOW
LOCALISED SINGLE
POLE SWITCH DOUBLE SWITCH
RED
BLACK
BLUE
MOTOR
LED LAMP

6
HANGING THE FAN
1. Ensure the fixing tab fits in the groove of the hanger ball. (Fig 3.)
2. Ensure the fixing tab is set at the highest point. (Fig 5.)
3. Suitable for installations up to 18 Degrees of Pitch. (Fig 4.)
FOR RAKED/SLOPED CEILINGS
Fig 3.
Fig 4. Fig 5.
Light Cable
INSTALLING THE UPPER CANOPY
Align screws on hang
Bracket with keyholes
in 'upper canopy' and
twist clockwise into
position.
Tighten screws
gently and ensure
there is a uniform
5mm (approx) gap
between ceiling and
canopy. Clip 'decorative screw cover' into place.
Note: For power supply,follow the wiring diagram Fig 6. (previous page)
1. “Clip receiver into
position on centre
strut of hanging
bracket”
2. Connect receiver
using quick connect
terminals to fan wire
terminals.
N/A for Models
"without Light"
Centre Strut
Once all the above steps have been followed, you are now ready to restore the mains
power supply.
Make sure there is nobody near or under the fan, then turn ON the fan (and light switch
if included in your model) to test.
Hang the assembled fan into the Hanging
Bracket making sure the groove on the
hanging Ball, locates into the Tab of the
Hanging Bracket. (Fig 3.)
Receiver Clip

7
x 2 AAA batteries included.
Note: Use good quality
Lithium batteries to extend
time between Battery
changes.
CCT DimF R
Fan off Light
1H 2H 4H
1
2
3
4
5
6
2. Adjust the fan speed from 1 (low) to 6 (high)
8. One, two and 4 hours run-on Timer.
4. Light ON/OFF.
5. Forward / Reverse alters the direction of blade rotation. (Summer / Winter)
6. Light colour (Cool, Natural and Warm) Adjust
7. Press and hold to adjust the Light intensity up or down.
A ' Beep ' will be heard at both Minimum, and Maximum brightness.
Release, then press again to reverse the dimming direction.
1. Turn the fan "OFF" only.
3. Creates a natural Breeze effect.
Fan off
1
2
3
4
5
6
Light
CCT
Dim
F R
1H 2H 4H
The remote handpiece comes factory paired with the remote receiver,
but if you wish to pair a remote handpiece to multiple fans, see below)
Step 1: Turn "OFF" isolation switch.
Step 2: Turn "ON" isolation switch and within 2 seconds, press fan off
button for 3-4 second until a "Beep-Beep" sound is heard.
(Repeat steps above if not successful)
Fan off
Also compatible with the Smartlife App
APP Wi-Fi CONTROL INSTRUCTIONS
1.Download the " Tuya Smart " app. Scan the QR code or download from
Apple Store (IOS) or Google Play (Android) .
Note: Ensure Remote control is paired to fan ( press and hold Fan off
2-3 sec, the fan will emit one beep)
Fan off

2.Register/sign up your Tuya smart (or Smart Life) account. Follow the
prompts using a choice of either mobile phone number or email address.
3.Turn on Wi-Fi on your mobile phone and ensure
fan is in the same Wi-Fi area.
4. Open your Tuya Smart App
and choose add device
5.Choose ‘Small Home Appliances’
then choose 'Fan (Wi-Fi)' .
Small
Home Ap...
8
6.Select a 2.4GHz Wi-Fi network and enter
password. (if your Wi-Fi is 5GHz,it should also
display a 2.4GHz version as a Wi-Fi
option available) please set to the 2.4GHz option.
Select ‘Next’.
Reset the device.
7. Reset the Fan, ready for pairing/syncing.
Note: this product does not have an indicator light.
Please follow resetting instructions listed below.
F R
Turn isolation switch(found on the wall in same
room as fan) to "OFF" for at least 15 seconds.
Then, turn isolation switch to ‘ON’ the fan
will emit one beep, and ‘within 10 seconds’
press and hold the F/R BUTTON on the
fan remote (3-5 sec).

9
Note:Please complete the pairing procedure
within 3 minutes of resetting.
Added successfully
Done
8. Select, "confirm the indicator is rapidly".
Then continue with Select "blink quickly" to begin the
pairing procedure.
This product does not have an indicator light, but
these directions must still be followed for successful
pairing.
Confirm the indicator is blinking rapidly.
Reset Device Step by Step
*
*
CCT DimF R
1
2
3
4
5
6
Select the status of the indicator
light or hear the beep:
Blink Slowly Blink Quickly
Adding device...
Ensure that the Wi-Fi signal is good

Or click on the fan to access the main control panel for full list
of control functions
10
You can control some basic functions from the home screen.
Please Note: a single fan can be linked to many phones as long
as they are using the same tuya or smartlife account.
SPYDA EC CEILING FAN
/
82
Colour Temperature
SPYDA EC CEILING FAN
LED Light ON OFF
Brightness
Natural white
1001
Closed after 01Hour00Minute
Timer
:
/
Fan ON OFF
1 6
Reverse
Direction
Speed
6
Mode Normal
Closed after 01Hour00Minute
Timer
:

11
This is the biggest cause for service calls, which are outside the manufacturer’s
warranty. If a fan has a fault, it will always be noticeable. even during the day.
Naturally when everything is quiet at night, you will be more inclined to hear
small noises, which may not be noticeable at other times. Blades spinning,
may cause a slight chopping sound which is more pronounced at higher speeds.
This is normal and is an indicator of high air movement.
Is the 'Lower Canopy touching the spinning parts? (adjust as required)
Is the'upper canopy'in contact with ceiling surface?

12
Except for an actual fault in manufacturing, which is extremely rare, noises and
vibrations are often more accentuated when a fan light is fitted. For instance, a
fan light diffuser that has not been tightened or worked loose can cause a rattle
Frequent care and maintenance will reduce this.