Ventair Mixflow Assembly instructions

INSTRUCTIONS

We recommend that you please check the following before installing
this product:
The VMFIL mixflow range in-line exhaust
fan that has been manufactured in accordance with the rigorous
standards of production as defined by the International Quality
Standards ISO 9001.All the components have been checked and tested
at the end of the manufacturing process.
1. The correct size has been received
2.The correct model has been received
3. The details on the rating label correspond to the electrical supply:
voltage, frequency etc.
Remove the unit from packaging and inspect for shipping damage
upon receiving this exhaust fan. lf the product is found to be damaged,
immediately contact your local authorised supplier.
This exhaust fans is suitable for operation within indoor
“environments only”.
This fan is suitable for the exhaust or supply of both conditioned and
un-conditioned airstreams within the temperature ranges(inclusive
of duct airstream’s temperature) of (-10℃ up to+50 ).℃
(a) Use this unit only in the manner intended by the manufacturer. lf you
have any questions contact the manufacturer.
(b) This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given
supervision or instructions concerning use of the appliance by a
person responsible for their safety.Children should be supervised
to ensure that they do not play with the appliance.
DO NOT OPERATE THE UNIT IF DAMAGED.
Model:VMFIL100, VMFIL150, VMFIL200, In-line Exhaust Fan

(f)
(d)
(e)
(g)
(h)
(j)
(k)
And

Duct work connection should be made with duct tape or duct fast-clamps
(available through your local distributor hardware retail store) to ensure
a good seal and secure connection.
INSTALLATION-Applications,Recommendations&Wiring
Installation tips:
Figure 1.Typical Appliations
:Model:VMFIL series
Multi-Point Exhaust System

Note:Please pay attention to the Air Direction when replacing the motor
wheel assembly.
4.Prepare the electrical wiring connection.Please refer to ELECTRICAL
CONNECTION section of this manual for wiring diagram.(Step 9-12
diagram below).
To start the installation the motor wheel assembly must first be removed,
loosening the two spring clips around the casing and remove.
(Step 1-3 diagram below).
2.Secure the mounting bracket fan flange assembly to a fixed structure.
(Step 4-5 diagram below).
3.Replace the fan motor wheel assembly and tighten the two spring clips
to secure the product.(Step 6-8 diagram below).

Warning:All electrical connections and disconnections must be
performed by a Licensed Electrician.
Wiring diagram
Warning:For your safety,all electrical work must be carried out by a
licensed electrcian.All electrical wiring must be in accordance with
latest national wiring rules AS/NZS 3000.
Warning:Ensure the power supply to the exhaust fan is switched OFF
before carrying out any installation and maintenance
Note:A double switch must be included in the electrical wiring of the
exhaust fan.

IMPORTANT:An additional all pole diconnection switch MUST be
cluded in the fixed wiring to provide isolation for maintenance.in
MAINTENANCE
IMPORTANT:BEFORE CARRYING OUT ANY MAINTENANCE OR
SERVICING,ENSURE THE UNIT IS DISCONNECTED FROM THE
MAIN ELECTRICAL SUPPLY.
This exhaust fan incorporates fully sealed bearings and therefore does
not require any lubrication .We would recommend inspection of the
product at least once every twelve(12) months to avoid the excessive
accumulation of dust and dirt on the inpeller.
To inspect the unit disconnect from electrical supply and remove from
ducting.lf any debris is evident on the impeller clean with a damp(not wet)
cloth.DO NOT USE any detergents or abrasive materials for cleaning.

Electrical
Max.Air Flow
Rate (H-L):
VMFIL200
VMFIL150
VMFIL100
130Watts50Watts30Watts
3
852/753m /h
3
561/438m /h
3
240/190m /h