This is a cut-out template card with size Φ240mm for the 200mm exhaust fan
READ AND SAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using any electrically powered product, basic safety precautions should always be followed, including
the following:
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT.
WARNING - to reduce the risk of fire, electrical shock or injury to persons or property:
• Always operate the product from a power source of the same voltage, frequency and rating as indicated on
the product identification plate.
• This appliance is not intended for use by persons (including children) with reduced physical,sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
• Do not operate any product with a damaged cord or plug, or after the product malfunctions, or is dropped
or appears damaged in any way.
• This unit is designed for indoor use only.
• Do not allow any foreign object to enter the grille openings as this may damage the unit and/or the user.
• Do not allow any ceiling insulation to cover any portion of the rear of the appliance.
• Do not attempt to modify the appliance.
• This unit is not suitable for use with exhaust ducting.
INSTALLATION
CAUTION: ANY ELECTRICAL WIRING MUST BE CARRIED OUT BY A LICENSED
ELECTRICIAN.
DO NOT INSTALL IN AN AREA WHERE WATER MAY BE SPLASHED ON THE
APPLIANCE.
1. Check for hidden timbers and wiring above the installation area.
2. Using the template as described over, mark the mounting hole on the ceiling. In order for the warranty
to be honoured the fan must be installed:
a. At least 2M above the ground.
b. At least 90cm from any hotplate and have at least 30cm clearance above the fan blades.
c. At least 20cm distance from side walls .
d. Ensure the power cord does not interfere with the fan blades.
e. Ensure any ceiling insulation or frame does not obstruct the airflow.
f. Clean the grille and blades regularly.
3. Cut the hole using a jigsaw, keyhole saw or hacksaw along the marked line.
4. Remove the grille (simply pulls free of the frame) and connect the plug to the power outlet. Insert the fan
assembly into the opening. For ceilings 13mm or less use step a). For thicker ceilings use step b).
a) Before inserting the fan into the opening, push the three bar clamps all the way out to hold the fan in
the ceiling. Push the fan into the ceiling opening and secure the exhaust fan by tightening the screws
securely (See Fig ).
b) Remove the three bar clamps. Use wood screws (not supplied) to secure the fan to the ceiling. Locate
screws in the 3 holes in the outer lip of the fan frame.
5. Place the grille over the fan assembly and push up until it snaps into place.
6. Precautions must be taken to avoid the back-flow of gases into the room from an open flue of gas or other
open-fire appliances.
CARE INSTRUCTIONS
Dirty fan blades and clogged grille drastically decrease the fan’s performance, working life and void the
warranty. Regular cleaning will ensure many years’ of trouble free operation. Switch the appliance off
before removing the grille.
GRILLE
Remove and wash in warm soapy water then rinse. A soft brush and sugar soap is recommended to remove
stubborn grease. Dry thoroughly before refitting.
FAN BLADE
Wipe blade with a cloth moistened with the above solution.
CAUTION: NEVER IMMERSE THE MOTOR IN CLEANING SOLUTION OR ANY OTHER LIQUID.
SERVICE
Apart from grille and blade cleaning there are no user serviceable components in the appliance. If repair is
required, contact the dealer from whom you purchased your appliance, together with your proof of
purchase, for a replacement.
WARRANTY
The Ventair Ceiling Exhaust Fan is warranted against defects in manufacturing and workmanship for a
period of 3 years.The warranty does not extend to installation of the unit or any associated wiring or any
damage caused installation or wiring.
The installation must be conducted by a licensed electrician and a suitable certificate of safety is to be issued
by the electrician who installed the unit. Warranty claims will be voided unless a certificate of safety can be
producd when required, prior to service or repair, Ventair only replaces unit upon receipt of your faulty
return to original point of sale. Please keep and present the original invoice to your service agent for
warranty services.
TEMPLATE
Check that no hidden timbers or wiring are in the area immediately above the hole. This template will
mark out a 240mm diameter hole for the 200mm fan.
Important Note
The supply cord cannot be replaced. If the cord is damaged the appliance should be rejected.
PTBX200
直径尺寸：240mm
Push in the
3 bar clamps
Tighten screw
MAIN TECHNICAL PARAMETERS
Input
220-240V 30W 39dB(A) Φ240mm
Power Noise Air Volume Hole-cutting Model No
50/60Hz
Size
PTBX200
273m³/H
Ventair is leading the Industry by ensuring all airflow data is gathered in accordance with International
standard ISO 5801.
* Airflow volume listed may show both ISO and non ISO supplied data.
• Non ISO: Generic factory supplied data, not tested to strict international standards or
guidelines and may vary according to individual manufacturers.
• ISO (International Organization for Standardization): An International standard tested
under strictguidelines providing accurate data and commonly used in the
professional specifying market.
