Ventair PRO-V Slimline VSLF100 Assembly instructions

INSTALLATION AND WIRING INSTRUCTIONS
Slimline Exhaust Fans
MODEL:
VSLF100
VSLF125
VSLF150
READ THE INSTRUCTIONS CAREFULLY BEFORE
INSTALLING AND OPERATING.

IMPORTANT INFORMATION
PARTS IDENTIFICATION
DIMENSIONS
WARNING: FOR YOUR SAFETY, ALL ELECTRICAL WORK MUST BE CARRIED OUT BY A
LICENSED ELECTRICIAN.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instructions on the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Fan must be installed at least 120cm above any hotplate, and must have at least 50cm
clearance at the rear of the blades.
Minimum installation height is 2.1metres from the oor to the bottom of the exhaust fan.
If the room where the fan is to be installed already contains a stove, water heater or a gas
re, it is essential to ensure that the air supply to the room is enough for both the fan and the
combustion appliance.
Please check that the appliance has not been damaged in transit before installation.
Ensure the electrical specications label corresponds to your electrical supply correctly.
MODEL A B C D Cut-Out
Hole Size
VSLF100 158 x 158mm 21 58 98 Ø98mm
VSLF125 180 x 180mm 21 71 116 Ø116mm
VSLF150 209 x 209mm 21 82 148 Ø148mm

IMPORTANT CONSIDERATIONS BEFORE INSTALLING
WIRING DIAGRAM
1. Adhere to the latest national wiring rules AS/NZS3000, for wiring and when installing in
bathrooms, nearby sinks and water taps.
2. For the exhaust fan to work efciently, replacement of air volume equivalent to what is
being extracted must be able to enter the room. In general this air would be drawn
under the door, or through a slightly opened window. If the room is air tight, the fan will
function poorly.
Supply cable entry
Terminal block
Fig 3.

INSTALLATION
WALL INSTALLATION
CEILING INSTALLATION
WARNING: For your safety, all electrical work must be carried out by a licensed electrician.
WARNING: Ensure the power supply to the exhaust fan is switched OFF before carrying out
any installation and maintenance.
NOTE: A double pole disconnection mechanism must be incorporated in the xed wiring
of the exhaust fan.
1. Find a suitable location and cut the appropriate size hole for the unit. Ensure there are
no cables or pipes behind the wall when cutting. The hole should slope slightly to the
external wall, this will allow drainage of any ingress from rain.
2. Remove the front panel of the exhaust fan and position against the wall, and mark the
four xing screw points and cable entry, and then drill to suit.
3. Place the exhaust fan through the cut out hole and position in place.
4. Connect the Live and Neutral supply wiring to the terminal block, replace the terminal
block cover and secure with screws.
5. Secure the fan to the wall via the four screws and mounting holes.
6. Replace the front panel and external shutter (External shutter not supplied).
1. Find a suitable location and cut the appropriate size diameter. Ensure there are no
cables or pipes above the ceiling when cutting.
2. Remove the front panel of the exhaust fan and position against the ceiling mounting
surface and mark the four xing screw points and cable entry, then drill to suit.
3. Place the exhaust fan through the cut out hole and position the exhaust fan in place.
4. Connect the Live and Neutral supply wiring to the terminal block, replace the terminal
block cover and secure with screws.
5. Secure the fan to the wall via the four screws and mounting holes.
6. Replace the front panel.
NOTE: Where ducting (not included) is used, ensure the outlet ducted is such that to
avoid the back-ow of gases into the room from the open ue of gas or other
fuel burning appliances.

DIMENSIONS
MODEL Rated Voltage
(V/Hz)
Input
(W)
Air-ow
(m3/h)
Noise
(dB)
Size
(mm)
VSLF100 220-240V~50Hz 15 70 34 100mm
VSLF125 220-240V~50Hz 20 120 36 120mm
VSLF150 220-240V~50Hz 25 210 40 150mm
MAINTENANCE AND SERVICE
Before carrying out any maintenance, ensure the power is switched OFF from the mains
power supply.
1. Wipe down the fascia and grilles with a wet soapy cloth only. Do not allow water to have
contact with the electrical parts, such as the motor.
2. Never use petrol, benzene, thinner or any other chemicals for cleaning the
ventilation fan.
3. Do not immerse resin parts into hot water over 60°C.
4. Do not place hot objects near or install nearby hot appliances.