Vermont Castings VCT323SSN/P Manual

30006291 3/13 Rev. 2 En
VCT323SSN/P Assembly Procedures
Tools Required: Knife or scissors, #2 & #3 Phillips screwdriver, 7/16” & 11/32” wrench or ratchet. Refer to
the parts list for hardware details. The use of a manual screwdriver is strongly recommended. A power drill
may cause damage to the unit or stripping of the protective coating.
CAUTION: This grill is intended ONLY to be used as a cart model, this grill cannot be built into an
enclosure.
CAUTION: The assembly of this grill requires two (2) people.
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting
or moving the grill is recommended. Protective eyewear and long sleeves are also strongly recom-
mended.
NOTE: Remove the protective plastic coating from the stainless steel, failure to do so will void the warranty.
6235
VC323SSP cover

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
230006291
VCT323SSN/P Assembly
Step 1: Unpack Carton and Verify Contents
Use a sharp cutting tool to remove the packaging. Remove layers of reinforced cardboard. Be careful not to
scratch or damage the nish of the metal parts when removing the sleeves and protective plastic. Open grill
lid and remove the parts. Unpack all parts and compare all contents to the parts list. Refer to the parts list for
fastener detail.
CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly is strongly
recommended.
Carton Contents
C.I. Cart Base
Cart Bottom Panel
Back Panel
Cart Right Side
Cart Left Side
Cart Door
Grease Shield
Inside Grill
Cooking Grates (2)
Heat Plates (3)
Grease Tray
Grease Cup
Grease Cup Holder
Swivel Caster (1)
Swivel Caster w/Brake (1)
Stationary Wheels (2)
Cart Mounting Brackets (2)
Upper Cart Brace
Cylinder Retainer
Left Side Shelf
Right Side Shelf
Shelf Spacer (2)
Shelf Support Brackets (4)
Manual Bag w/Hardware, Match
Holder

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
3
30006291
VCT323SSN/P Assembly
Step 2: Attach Cart Sides, Bottom and Base
Step 3: Attach Back Panel
Parts Required:
(1) Back Panel
(8) #10-24 x 1/2” Screws (50000337)
(8) #10-14 Lock Nuts (50000182)
Figure 2
Assemble as shown and tighten fasteners.
Parts Required:
(1) C.I. Cart Base
(1) Cart Bottom Panel
(1) Cart Left Side
(1) Cart Right Side
(4) 1/4-20 x 3/4” Hex Head Bolts (1201381)
(4) 1/4-20 Hex Nuts (30005406)
(4) 1/4 Washer (1202471)
Figure 1
Assemble as shown - nger tight.
B448
cart assy
Detail ‘A’
Right Side
Hex Nut
Left Side
Bottom
Panel
Washer Hex Head
bolts
B448
C.I. Cart Base
Detail ‘A’ -
Four (4) Corners
Figure 2
B453
attach back panel
Detail ‘A’
Back Panel
Screws
Lock Nuts
Detail ‘A’
B453
Figure 1

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
430006291
VCT323SSN/P Assembly
B454
attach brace & retainer
Step 4: Attach Upper Cart Brace and Tank Retainer
Parts Required:
(1) Upper Cart Brace
(4) #10-24 x 1/2” Screws (50000337)
(4) #10-24 Lock Nuts (50000182)
(1) Tank Retainer
Figure 3
Assemble as shown and tighten screws.
Figure 3
Upper Cart
Brace
Screws
Left Side Panel
Rear View
Lock Nuts
LP Tank Retainer
Retainer Clip
B454
Front View

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
5
30006291
VCT323SSN/P Assembly
Step 5: Attach Door and Complete Cart
Parts Required:
(1) Door
(1) Door Handle
(2) #10-24 x 1/2” Screws (with handle)
(4) #10-24 x 1/2” Screws (50000337)
Figure 4
Assemble as shown and tighten fasteners. Completely
tighten fasteners from Step 2.
B455
attach door
Detail ‘A’ -
Four Places
Detail ‘A’
Screws
Door
Handle
B455
Figure 4
Detail ‘B’
Detail ‘B’

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
630006291
VCT323SSN/P Assembly
Step 6: Attach Casters to Cart Base
Parts Required:
(1) Upper Cart Assembly
(2) Stationary Wheels
(1) Swivel Caster
(1) Swivel Caster w/Brake
(8) 1/4-20 x 1/2” Screws (30005405)
Figure 5
Assemble as shown and tighten fasteners.
B456
attach wheels
Swivel Caster
w/Brake
Swivel
Caster
Stationary
Wheels
B456
Figure 5
Step 7: Attach Cart Mounting Brackets
Parts Required:
(2) Cart Mounting Brackets
(8) #10-24 x 1/2” Screws (50000337)
(8) #10-24 Lock Nuts (50000182)
Figure 6
Assemble as shown and tighten fasteners.
B457
attach mounting brackets
Cart Mounting
Brackets
Screws
Lock Nuts
B457
Figure 6

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
7
30006291
VCT323SSN/P Assembly
Step 8: Attach Grease Cup Holder, Grease Cup and Grease Shield
Parts Required:
(1) Grease Cup Holder
(1) Grease Cup
(1) Grease Shield
(4) #10-24 x 1/2” Screws (50000337)
(4) #10-24 Lock Nuts (50000182)
Figure 7
Assemble as shown and tighten fasteners.
B458
grease cup
Grease Shield
Grease
Cup
B458
Figure 7
Grease Cup Holder
Screws
Lock Nut

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
830006291
VCT323SSN/P Assembly
Step 9: Attach Grill to Cart Assembly
CAUTION: This step may require 2 people.
Parts Required:
(4) #10-24 x 1/2” Screws (50000337)
Figure 8
Assemble as illustrated and tighten fasteners.
CAUTION: Do not damage gas line. The hose assembly should be placed in opening
between grease shield and front of cart.
B459
grill to cart
Grill
Screws
Cart Assembly
B459
Figure 8

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
9
30006291
VCT323SSN/P Assembly
Step 10: Attach Left & Right Side Shelves
Parts Required:
(1) Left Side Shelf
(1) Right Side Shelf
(2) Shelf Spacers
(4) Shelf Support Brackets
(8) #10-24 x 1/2” Screws (50000337)
(8) 1/4-20 x 1/2” Screws (30005405)
Figures 9 & 10
Assemble as shown and tighten fasteners.
B473
shelf supports
Shelf Spacer
Shelf Support Bracket
#10-24 x 1/2”
Screws
B473
Figure 9
B477
side shelves
Figure 10
Side Shelf
Detail ‘A’
Detail ‘A’
1/4-20 x 1/2” Screws
B477

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving
the grill is recommended.
10 30006291
VCT323SSN/P Assembly
Step 11: Attach Paper Match Holder
Parts Required:
(1) Paper Match Holder Assembly
Figure 11
Attach the supplied paper match holder and chain assembly to the inside of the cart
door.
Secure chain assembly to top screw of door handle. Store chain inside door when
not in use.
Figure 11
B507
paper match holder
B507