Vertiv 547692 User manual

NetSure™ RDB Series
Installation and User Manual, Section 6041
(Revision K, April 28, 2017)
Specification Number: 547692, 547693, 547499, 547694, 547695, 547615,
547696, 547697, 547503, 547500, 547698, 547699, 547501

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
This page is intentionally blank.

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[i]
Table of Contents
Admonishments Used in this Document ................................................................................................................ ii
Important Safety Instructions .............................................................................................................................. iii
Save These Instructions ...........................................................................................................................................iii
Installation ........................................................................................................................................................... 1
Shipment Inspection ............................................................................................................................................... 1
Installing the Rack PDU ........................................................................................................................................... 1
Electrical Connections ........................................................................................................................................... 3
Connecting the Rack PDU DC Input ......................................................................................................................... 3
Connecting the Rack PDU’s DC Output to Customer Equipment .............................................................................. 3
Connecting External Circuit Breaker Alarms ............................................................................................................. 4
Specifications and Technical Data .......................................................................................................................... 5
Conformity and Standards ...................................................................................................................................... 5
Environmental Characteristics ................................................................................................................................. 5
Specifications ......................................................................................................................................................... 5
Dimensions ............................................................................................................................................................ 6
Input Quick Connect Kit ........................................................................................................................................ 12
Output Cable Assemblies ...................................................................................................................................... 12
Replacement Circuit Breakers ............................................................................................................................... 13
Operation ........................................................................................................................................................... 14
Connecting Power to the Loads ............................................................................................................................. 14
Removing Power from the Loads ........................................................................................................................... 14
Alarms .................................................................................................................................................................. 14

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[ii]
Admonishments Used in this Document
DANGER!
Warns of a hazard the reader will be exposed to that will likely result in death or serious injury
if not avoided
. (ANSI, OSHA)
WARNING!
Warns of a potential hazard the reader may be exposed to that could result in death or
serious injury if not avoided
. This admonition is not used for situations that pose a risk only to
equipment, software, data, or service
. (ANSI)
CAUTION!
Warns of a potential hazard the reader may be exposed to that could result in minor or
moderate injury if not avoided
. (ANSI, OSHA) This admonition is not used for situations that pose a risk
only to equipment, data, or service, even if such use appears to be permitted in some of the applicable
standards
. (OSHA)
ALERT!
Alerts the reader to an action that must be avoided in order to protect equipment, software,
data, or service
. (ISO)
ALERT!
Alerts the reader to an action that must be performed in order to prevent equipment damage,
software corruption, data loss, or service interruption
. (ISO)
FIRE SAFETY!
Informs the reader of fire safety information, reminders, precautions, or policies, or of the
locations of fire
-fighting and fire-safety equipment. (ISO)
SAFETY!
Informs the reader of general safety information, reminders, precautions, or policies not related
to a particular source of hazard or to fire safety
. (ISO, ANSI, OSHA)
Danger
Warning
Caution
Alert
Alert
Fire Safety
Safety

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[iii]
Important Safety Instructions
Save These Instructions
WARNING!
Please read and follow all safety
information!
Failure to observe the safety information
listed below may result in electric shock, fire hazards, or
serious injury. Please safeguard this Installation and
User Manual.
Intended Use
The NetSure™ RDB Rack PDU (Power Distribution Unit) is designed
to deliver power to information technology and
telecommunication equipment.
Operate the Rack PDU in an indoor environment only within an
ambient temperature range and a relative humidity range as listed
in “Environmental Characteristics” on page 5. Install the Rack PDU
in a clean environment, free of conductive contaminants,
moisture, flammable liquids, gases and corrosive substances.
•Do not use the Rack PDU in moist environments. If the
Rack PDU is exposed to moisture, immediately
disconnect the Rack PDU from DC input power by
opening the circuit breaker or removing the fuse or
breaker supplying DC input to the Rack PDU. Send the
Rack PDU to the manufacturer for inspection.
•Do not use the Rack PDU for household applications.
Installation and Operation
Improper installation and operation may cause overheating and
lead to increased fire hazard. It may also destroy the device and
damage other connected systems.
•Installation and start-up must be performed by a
qualified service engineer.
•Make sure that the total input current of the connected
systems does not exceed the current rating specified on
the rating plate of the Rack PDU.
Electrical Safety
Damaged Rack PDUs or connected cables increase the risk of
electric shock or smoldering fire.
•Check the unit for external signs of damage prior to start-
up operation! Do not operate the device if you detect
any damage or other deficiencies.
•Only use the supplied DC input power cable.
Personal Safety
Careless handling increases the risk of electric shock.
•Never touch the outlets or the Rack PDU with wet or
moist hands.
Service
Repairs should only be performed by qualified service technicians.
Unauthorized changes, modifications, or repairs of the device are
performed at the owner’s risk and will void all warranty claims.
•Do not open the Rack PDU.
•Please contact the nearest customer service center in
case of malfunction! Damage and defects must be
repaired immediately.
•Always disconnect the unit from power before
troubleshooting.
Warning

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[iv]
This page is intentionally blank.

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[1]
Installation
The NetSure™ RDB Rack PDUs (Power Distribution Units) are
designed to be installed on the left and/or right rear frames of IT
racks. They can be mounted directly to the rack or use Rack PDU
Mounting Kit P/N 547665. See “Dimensions” starting on page 6
for hole dimensions.
Shipment Inspection
Unpack the shipping container, inspect all items for damage and
verify that the shipment is complete and undamaged. Report any
damage to your local Vertiv Co. representative and the carrier.
Installing the Rack PDU
WARNING!
Ensure proper grounding.
The Rack PDU’s
"Ground Lead Bracket" must be ground bonded to the
mounting bracket (if used) or rack frame. The mounting
bracket (if used) must be ground bonded to the rack
frame. The rack frame must be ground bonded to your
site ground. This is typically accomplished through the
use of paint free areas and/or grounding washers used
when mounting the components.
Installing the Rack PDU Directly to a Rack Frame or Existing
Mounting Bracket
Install the Rack PDU directly to the rack frame or existing
mounting bracket as shown in Figure 1. Note that the supplied
"Ground Lead Bracket" is to be placed between the PDU and the
rack frame or existing mounting bracket as shown in Figure 1. Use
the supplied 1/4-20 screws and 1/4-20 KEPS nuts.
Installing Rack PDUs to a Rack Frame using the Optional
Mounting Bracket
If using the Rack PDU Mounting Kit, install the Rack PDU mounting
bracket to the left and/or right rear frame of the rack using the
appropriate hardware that fits to the cabinet that will be used.
Install the Rack PDUs to the Rack PDU mounting bracket that was
previously installed on the frame as shown in Figure 2. Note that
the supplied "Ground Lead Bracket" is to be placed between the
PDU and the mounting bracket as shown in Figure 2.
Figure 1. Mounting Rack PDUs Directly to Rack Frame
Warning

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[2]
Figure 2. Mounting Rack PDUs using Optional Mounting Bracket Kit

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[3]
Electrical Connections
Connecting the Rack PDU DC Input
The Rack PDU’s input is designed to be fed from a 200A (max) breaker or fuse using the factory supplied and connected DC input cable
assembly and the customer connected input quick connect kits. See Figure 3.
Figure 3. DC Input Connections
Connecting the Rack PDU’s DC Output to Customer Equipment
The Rack PDU’s output circuit breakers are connected to customer equipment via the separately ordered output cable assemblies. A
ground lead is also supplied with each output cable. Each ground lead is terminated with a connector on one end (which mates with a
connector on a ground wire factory connected to the "Ground Lead Bracket") and left unterminated on the other end. See Figure 4.
Figure 4. DC Output Connections

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[4]
Connecting External Circuit Breaker Alarms
Negative 48Vdc is provided to a set of alarm terminals if any circuit breaker is in the OFF position. See Figure 5.
Figure 5. Alarm Connections

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[5]
Specifications and Technical Data
Conformity and Standards
The NetSure RDB Rack PDU (Power Distribution Unit) has the following agency approval ratings:
•UL 60 950-1 + UL 1801 - Recognized (cURus)
•In accordance with the Low Voltage Directive, 2006/95/EEC and including amendments by the CE Marking Directive,
93/68/EEC.
Environmental Characteristics
The NetSure RDB Rack PDU (Power Distribution Unit) is designed to operate under the following environmental conditions without
damage or degradation in electrical operating characteristics:
Operating Temperature
-40°F to +104°F (-40°C to +40°C) (Models L6 and L15).
-40°F to +113°F (-40°C to +45°C) (Models H2, H3, and M6).
Storage Temperature
-40°F to +176°F (-40°C to +80°C).
Relative Humidity
0 to 95%, non-condensing.
Operating Elevation
6562 ft (2000m) at full power.
Specifications
Model Part
Number
Number
of
Outlets
Power Rating per Outlet Power Rating per PDU Input/Output
Voltage
(nominal)
RDB - Basic Rack PDUs
Max Watts
Max Amps1
Max kW
Max Amps1
L6
547692
6
420
10
2.5
60
-48Vdc
547693
630
15
3.8
90
547499
840
20
5.0
120
L15
547694
15
420
10
6.3
150
547695
630
15
8.42
2002
547615
840
20
8.42
2002
M6
547696
6
1050
25
6.3
150
547697
1260
30
7.6
180
547503
1470
35
8.42
2002
H2
547500
2
3360
80
6.7
160
H3
547698
3
2100
50
6.3
150
547699
2520
60
7.6
180
547501
2940
70
8.42
2002
1 Max Amps rated at end of battery discharge (42V).
2 PDU power rating limited to 200A, 8.4kW each.

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[6]
Dimensions
NetSure™ RDB L6, P/Ns 547692, 547693, 547499
Figure 6. NetSure™ RDB L6, P/Ns 547692, 547693, 547499

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[7]
NetSure™ RDB L15, P/Ns 547694, 547695, 547615
Figure 7. RDB L15, P/Ns 547694, 547695, 547615

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[8]
NetSure™ RDB M6, P/Ns 547696, 547697, 547503
Figure 8. RDB M6, P/Ns 547696, 547697, 547503

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[9]
NetSure™ RDB H2, P/N 547500
Figure 9. RDB H2, P/N 547500

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[10]
NetSure™ RDB H3, P/Ns 547698, 547699, 547501
Figure 10. RDB H3, P/Ns 547698, 547699, 547501

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[11]
NetSure™ RDB Mounting Bracket, P/N 547665
Figure 11. RDB Mounting Bracket, P/N 547665
6.81
2.68
6.000 (TYP)
1.375
1.75 (TYP)
0.218 X 0.562 SLOT(II)
0.218 X 0.375 SLOT(4)
0.281 X 1.000 SLOT(14)
0.218 X 0.562 SLOT(20)
0.25
o0.147+0.002 (40 PLCS)
2.56
R 0.062 REF
3.69
0.25 X 45 (TYP)
o
73.63
0.000
0.75 2.250
3.25
0.64 1.33 2.02 2.70 3.39
0.000
0.845
3.032
4.785
14.656
19.867
22.847
29.277
32.718
35.617
38.012
40.909
44.357
50.780
53.761
58.971
68.842
70.595
72.782 71.937
1.687

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[12]
Input Quick Connect Kit
Provides the mating connector and contacts for the DC Input Cable Assembly factory supplied and connected to the Rack PDU.
P/N
Contact Size
Mating Anderson
Powerpole
Connector
(AWG) (Metric)
547668
1/0
55mm²
350A, Red
(SB350)
547669
2/0
70mm²
547670
3/0
95mm²
547671
4/0
120mm²
Output Cable Assemblies
P/N 547595, P/N 547613 and P/N 555654
Figure 12. P/N 547595, P/N 547613 and P/N 555654

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[13]
Output Connector Kits (P/N 554878 and P/N 554944)
Figure 13. Output Connector Kits (P/N 554878 and P/N 554944)
Replacement Circuit Breakers
NetSure
Rack PDU
P/N
Replacement
Circuit Breakers
P/N
547692
547694
142907 (10A)
547693
547695
142908 (15A)
547499
547615
141801 (20A)
547696
143041 (25A)
547697
143042 (30A)
547503
141802 (35A)
547698
142951 (50A)
547699
142952 (60A)
547501
142953 (70A)
547500
142955 (80A)

NetSure™ RDB Series
Installation and User Manual, Section 6041
Spec. No: 547692, 547693, 547499, 547694, 547695, 547615, Document Code: Section 6041
547696, 547697, 547503, 547500, 547698, 547699, 547501 Revision K, April 28, 2017
[14]
Operation
WARNING!
Improper operation may cause overheating and lead to increased fire hazard. Improper operation may also
destroy the device and damage other connected systems.
Make sure that the total input current of the connected systems
does not exceed the current rating specified on the rating plate of the Rack PDU. Please refer to the operating instructions or
the rating plates of the connected systems or the circuit breaker for power specifications.
Connecting Power to the Loads
To connect DC power to the load(s), operate the respective circuit breaker on the Rack PDU to the ON position.
Removing Power from the Loads
To disconnect DC power from the load(s), operate the respective circuit breaker on the Rack PDU to the OFF position.
Alarms
Local Alarm Indicator
Each Rack PDU contains a circuit breaker alarm indicator. This indicator illuminates Red if any circuit breaker on the Rack PDU is in the
OFF position.
External Circuit Breaker Alarm
Negative 48Vdc is supplied to a set of terminals when any circuit breaker on the Rack PDU is in the OFF position. These terminals may be
connected to customer external alarm circuits.
Warning