Vestamatic Rolltec Plus G/S User manual

- 40 -
G
Safety precautions
– Contact a professional electrician to install the control
as well as for setting of the DIP switches on the rear
panel of the device, because the power supply requires
a power supply of 230VAC, 50 Hz.
– Check the control system for signs of mechanical
damage after unpacking. If you notice any shipping
damage, do not start up the control system and notify
your supplier immediately.
– The control system should only be used for the purpose
specified by the manufacturer (refer to the operating
instructions). Any changes or modifications thereof are
not permissible and will result in loss of all warranty
claims.
– If the control unit cannot be operated without presenting
a hazard, it must be switched off and prevented from
being switched on unintentionally.
– When performing work on the windows, controls or
connected shades, protect them against unauthorised
or unintentional operation.
Ä
Installation and Operating Instructions
Rolltec Plus G/S
Roller Shutter Control
Art.-no. 01805050

Introduction General page 43
Manual mode page 44
Automatic mode page 45
Programming General page 46
the basic Summer/winter time page 47
functions Current time page 48
Note page 49
Up time page 50
Down time page 51
Random generator page 52
Programming Week function page 53
the special Astro function / Run time correction page 54 – 57
functions Astro function – Germany page 58
Astro function – Europe page 59
Reverse function page 60
Example for DIP switch setting page 61
- 41 - G
Contents
G/S functions General page 62
Functional description broken glass sensor page 63
Functional description sun protection page 64
Setting the response (sun intensity) page 65
Troubleshooting page 66
Installation Notes for professional electricians page 67 – 68
Installation instructions / Technical data page 69
Wiring diagram page 70
Installation broken glass sensor page 71 – 72
Installation lux sensor page 73 – 74
Wiring diagram Inside back cover
Overview operating elements Inside back cover
- 42 -
G
Contents

The delivery extent of the control includes the following items:
1. Cover cap
2. Control
3. Supporting frame for control
4. Adjustment tool
5. JUNG Cover frame, 1-fold, “CD 500”
In case of power failure, the entire display starts flashing. Yet, the
previously programmed times remain saved for several years.
The times or functions, you have previously programmed, can be
checked by performing a quick run (i. e. g. test of the sun protection).
Press the time and day button simultaneously for 3 seconds to activate
the quick run. The time function will now run 60 times faster. Shortly
tap the time and day button simultaneously to stop the quick run.
- 43 - G
General Introduction
The control features a selector switch with which manual mode (H) or
automatic mode (A) can be selected.
Push the selector switch to (H), all the way to right until you hear the
“click”, in order to activate the manual mode.
All automatic functions are now disabled. Pressing the up or down
button will move the roller shutters up or down.
Simply press the opposite button to stop the motion, i.e.:
press the down button, if the roller shutter is moving up,
press the up button, if the roller shutter is moving down.
Accurate positioning of the roller shutter is guaranteed because the
roller shutter will only move up or down again after the up or down
button has been pressed.
- 44 -
G
Introduction Manual mode

Push the selector switch to (A), all the way to the left until you hear
the “click”, in order to activate the automatic mode.
The automatic mode is now activated and the roller shutter will
move up and down at the programmed times. Regardless of the
programmed times, it is still possible to move the roller shutter up
and down by pressing the up or down button and the programming
remains unaffected.
If you press the up or down button longer than 2 seconds, the roller
shutter moves up or down.
Simply press the opposite button to stop the motion, i.e.:
press the down button, if the roller shutter is moving up,
press the up button, if the roller shutter is moving down.
The roller shutter will only move up or down again after the up or
down button has been pressed.
By simply pushing the selector switch to manual mode (H), the auto-
matic mode can be interrupted for an extended period of time.
After selecting automatic mode again, the control will execute the
last pending command from the automatic mode. The last pending
command will also be executed when resetting after power failure.
- 45 - G
Automatic mode Introduction
After the installation has been completed correctly (for instructions
please see pages 67 to 74), you can start programming.
Carefully pull to remove the cover cap and press the reset button with
the delivered adjustment tool or something else suitable.
Pressing the reset button will activate the default times pre-programmed
by the manufacturer.
Current time – 0ß8:0ß0
Up time – 0ß6:0ß0
Down time – 2ß0:0ß0
On the following pages, you will find instructions how to customize
these times to your personal requirements.
- 46 -
G
Basic functions General
IMPORTANT!
Please note that the control cannot be programmed in case
of power failure.
x

The display will indicate which time has been set.
The (S) in the upper left hand corner of the display stands for summer
time.
(0S9:0ß0)
The (W) in the upper right hand corner of the display stands for
winter time.
(0ß8:0W0)
If the present setting is incorrect and does not correspond with the
current time, you can simply update the time by pressing the summer/
winter button. The selected setting will appear in the display and the
time will be changed by one hour.
- 47 - G
Summer/winter time Basic functions
By operating the combination of set and time button you can set the
current time.
Setting the time can be performed as follows:
1. Press the set button first and keep it pressed, then:
A. Press the time button and keep it pressed to fast forward the
time.
B. Shortly tap the time button to slow forward the time.
or
2. Press the time button first and keep it pressed, then:
A. Press the set button and keep it pressed to fast reverse the
time.
B. Shortly tap the set button to slow reverse the time.
- 48 -
G
Basic functions Current time

The control is delivered with the following manufacturer’s default up
and down times (day function is activated):
Daily up time – 0ß6:0ß0 p.m.
Daily down time – 2ß0:0ß0 a.m.
Please find the manufacturer’s default DIP switch settings in the
tables on page 58 and page 61.
- 49 - G
Note Basic functions
IMPORTANT!
It is important to push the selector switch
“automatic/
manual-mode” to automatic mode (A), in order to be able
to perform the following programming steps.
Check the current setting. If the selector switch is not set on
(A), correct the setting by pushing it all the way to the left
until you hear the “click”.
x
By operating the combination of set and up button you can set the
up time.
Setting the up time can be performed as follows:
1. Press the set button first and keep it pressed, then:
A. Press the up button and keep it pressed to fast forward the
up time.
B. Shortly tap the up button to slow forward the up time.
or
2. Press the up button first and keep it pressed, then:
A. Press the set button and keep it pressed to fast reverse the
up time.
B. Shortly tap the set button to slow reverse the up time.
The display will now indicate the set value. Once the programming
buttons are no longer operated, the display will indicate the current
time again. Tapping the up button will check the set value and the
display will again indicate the previously set up time. After approx.
2 seconds, the display will indicate the current time again.
- 50 -
G
Basic functions Up time

By operating the combination of set and down button you can set
the down time.
Setting the down time can be performed as follows:
1. Press the set button first and keep it pressed, then:
A. Press the down button and keep it pressed to fast forward the
down time.
B. Shortly tap the down button to slow forward the down time.
or
2. Press the down button first and keep it pressed, then:
A. Press the set button and keep it pressed to fast reverse the
down time.
B. Shortly tap the set button to slow reverse the down time.
The display will now indicate the set value. Once the programming
buttons are no longer operated, the display will indicate the current
time again. Tapping the down button will check the set value and the
display will again indicate the previously set down time. After approx.
2 seconds, the display will indicate the current time again.
- 51 - G
Down time Basic functions
The random generator generates the so-called random time which
causes the roller shutters to move up or down with a deviation of
+/-15 minutes to the previously programmed times(*).
The “randomly” moving up and down roller shutters give the impres-
sion of an inhabited house and thus provide additional protection in
case the house owner is absent for an extended period of time.
Simply press the random button to activate the random generator.
The display will now indicate
a (Z) in the upper right hand
corner. (0ß8:0ß0Z
Press the random button again to deactivate the random generator.
The random generator is now turned off, the (Z) in the display will
disappear and the roller shutter will move up and down accurately at
the times you have previously programmed.
(*)Annotation: If the Astro function is activated, the times will deviate
by +/-15 minutes from the actual sunrise and sunset
times.
- 52 -
G
Basic functions Random generator
NOTE!
The random generator will disable any previously set reverse
function (please see page 60).
v

The week function enables you to program a particular up and down
time for each individual day of the week.
In order to activate the week function, all DIP switches in the rear of
the housing must be set according to the table on page 61.
The following times were preset for this operation mode by the
manufacturer:
Up time Monday through Friday – 0ß6:0ß0
Down time Monday through Friday – 2ß0:0ß0
Saturday / Sunday – no preset time
If you wish different up or down
times, perform the following steps: (QS8:0ß0)
Press the day button. The display
will show a new day of the week
after every press. (0w8:0ß0)… etc.
Perform the steps described on page 50 and 51 to program the up
and down times for the currently displayed day.
- 53 - G
Week function Special functions
The Astro function is basically an electronical calendar. Depending
on the stored sunrise and sunset times, the up or down times are
automatically corrected under consideration of the geographical
location of your residence. This correction is based on the up or down
times you previously set.
For more information on the programming of the Astro function please
see page 56.
Example:
You have activated the Astro function and previously programmed
the following up and down times according to the instructions on
page 50 and page 51:
Up time – 0ß6:3ß0 (½ an hour before sunrise according to
the diagram on page 57)
Down time – 1ß9:3ß0 (½ an hour before sunset according to
the diagram on page 57)
Given the current calendar week 14.
In this example, the roller shutter does not move up at 6:30, as pro-
grammed but moves up at 7:00 when the sun rises.
In the evening, it moves down at 19:30 at the programmed time.
- 54 -
G
Special functions Astro function

Note:
If the up time is programmed before sunrise, the roller shutter moves
up at sunrise.
If the up time is programmed after sunrise, the roller shutter moves
up at the programmed up time.
If the down time is programmed after sunset, the roller shutter moves
down at sunset.
If the down time is programmed before sunset, the roller shutter moves
down at the programmed down time.
- 55 - G
IMPORTANT!
Activating the Astro function automatically disables the
week function.
x
Astro function Special functions
Activating the Astro function and setting the current calendar week
will be performed in one programming step.
First press the set button and keep it pressed. Then press the day
button twice.
The display will indicate
the following: (ßßßß0ß1A
Now set the current calendar week by pressing the day button.
Keep pressing the set button. Each additional pressing of the day
button will move to the next calendar week.
After you have set the current calendar week and released both but-
tons, the Astro function will be activated. The display will now switch
to the current time. The display will continue to indicate the (A) in the
upper right hand corner.
Keep the set button pressed and press the day button until the dis-
play indicates “ 0ß0 ” in order to deactivate the Astro function.
- 56 -
G
Special functions Astro function
NOTE!
In order to obtain optimum performance of the Astro func-
tion, the geographical location of your residence must be set
by means of the DIP switches (see tables on page 58 and 59).
v

G
Below the switching sequence is presented in the course of an entire year under con-
sideration of summer/winter time, at an up time preset at 6:30 and a down time preset
at 19:30. These times relate to 10° of eastern longitude and 50° of northern latitude
which corresponds to the geographical location of the city of Würzburg. Setting DIP
switch 6 to “ON” will delay the down time of the roller shutter by 30 minutes.
Run time
correction:
- 57 -
DIP 6 Correction
OFF no delay
ON down command 30 minutes delayed
Astro function/Run time correction Special functions
G- 58 -
DIP 2 DIP 3 DIP 4 DIP 5 Area
OFF OFF OFF OFF Schleswig-Holstein, Northern Lower-Saxony
OFF OFF OFF ON Mecklenburg-Vorpommern
OFF OFF ON OFF
North-Rhine Westphalia, Southern Lower-Saxony
OFF OFF ON ON Brandenburg, Saxony-Anhalt
OFF ON OFF OFF Rhineland-Palatinate, Saarland, Hesse
OFF ON OFF ON Saxony, Thuringia
OFF ON ON OFF Baden-Württemberg
OFF ON ON ON Bavaria
Special functions Astro function – Germany
= Manufacturer’s default setting:
Schleswig-Holstein,
Northern Lower-Saxony
The respective DIP switches are located on the rear panel of the control.
Y12345C

The respective DIP switches are located on the rear panel of the control.
G
- 59 -
DIP 2 DIP 3 DIP 4 DIP 5 Area
ON OFF OFF OFF Scandinavia
ON OFF OFF ON Great Britain
ON OFF ON OFF Northern France, Benelux
ON OFF ON ON Germany
ON ON OFF OFF Southern France
ON ON OFF ON Switzerland, Austria, Northern Italy
ON ON ON OFF Spain
ON ON ON ON Southern Italy, Sicily, Corsica, Sardinia
Astro function – Europe Special functions
G
After the roller shutter has moved down automatically at the pro-
grammed time, the reverse function causes the roller shutter to shortly
move up shortly for airing purposes or to let pets go outside.
The reverse time can be set with DIP switches 7 and 8 and will only
be executed at the programmed day, week and sunrise/sunset times
during automatic operation. The reverse function can also be exe-
cuted by pushing the down button during automatic operation.
Setting reverse time:
The display will indicate the
set reverse time with the
symbol (O).
This symbol flashes on the
display during execution of
the reverse time.
The respective DIP switches are located on the rear panel of the control.
- 60 -
DIP 7 DIP 8 Reverse time
OFF OFF none
OFF ON 2 seconds
ON OFF 4 seconds
ON ON 10 seconds
Special functions Reverse function
IMPORTANT!
The reverse function is only initiated 2 minutes after the
down pulse has been transmitted.
x

The table below shows the various setting options. The position of S1
determines whether day or week function was selected.
Preset default
setting: Day function (S1 = OFF) No Astro correction time (S6 = OFF)
No reverse function (S7 and S8 = OFF)
Day
Y123$5678X
Example of the DIP switch position for North-Rhine Westphalia.
For other states, please see pages 58 and 59.
For DIP switch S6, see page 57, for S7 and S8 see page 60.
Week
Y!wert678X
DIP switches S2 – S5 do not have any function for this setting.
For DIP switch S6, see page 57, for S7 and S8 see page 60.
The respective DIP switches are located on the rear panel of the control.
- 61 - G
Example for DIP switch setting Special functions
Your control features two additional useful functions:
1. Broken glass sensor (G)
The function “broken glass sensor” is only activated in the auto-
matic operation.
2. Sun protection (S)
The function “sun protection” can only be operated in the automatic
operation within the previously programmed up and down times.
- 62 -
G
G/S functions General
NOTE!
Standard length of the lux sensor cable – 1 or 2 m
Standard length of the broken glass sensor cable
– 1 or 2 m
Cables of up to 5 m length can be delivered for both functions.
v

In case of broken glass, the roller shutter moves down without delay.
The display will now indicate
the broken glass symbol (g): (0S8:0g0)
The previously programmed up time will no longer be considered,
i.e. the roller shutter does not move up at the programmed up time
because of safety reasons. Simply press the up button in order to
resume the normal operation. The broken glass symbol in the display
goes off and the roller shutter moves up or down at the programmed
up and down times.
Annotation: A broken glass signal is released as soon as the broken
glass sensor detects a massive shock or broken glass
within the sensing range. The sensing range amounts
to approx. 1 square meter (please refer to the picture on
page 71). Therefore, several broken glass sensors and a
distributor box should be installed on larger windows.
- 63 - G
Functional description broken glass sensor G/S functions
When the lux sensor is exposed to sun rays, the sun symbol will flash
in the display. After the sensor measures 1 minute of continuous sun-
shine, the roller shutter moves as far down to cover the lux sensor.
In order to clear the lux sensor for further monitoring, the roller shutter
then moves a few inches up. We call this roller shutter position
“shade position”.
The display indicates the current light inten-
sity with the corresponding symbols (S):
(Example: strong light intensity) s0S8:0ß0)
If the lux sensor cannot detect any sun rays over a continuous period
of 16 minutes, the roller shutter will move up again. The sensor signals
are checked on a regular basis and the position of the roller shutter
position will be corrected accordingly in the course of a sunny day.
Remove the lux sensor, if you do not need to use the sun protection
function for an extended period of time.
- 64 -
G
G/S functions Functional description sun protection
IMPORTANT!
The lux sensor is only activated in between the up and
down times. If the current time does not lie within these
times, the display will indicate a moon symbol.
x

- 65 - G
Set the response to the sun intensity with the potentiometer and the
delivered adjustment tool. Carefully pull to remove the cover cap of
the control.
rThe roller shutter
moves down at a
low sun intensity
(approx. 12 kLux).
oThe roller shutter
moves down at a
medium sun inten-
sity (approx. 17 kLux).
lThe roller shutter
moves down at a
high sun intensity
(approx. 22 kLux).
Sun response delay: 1 minute
Sun reset delay: 16 minutes
Setting the response (sun intensity) G/S functions
The roller shutter does not move up and down automatically.
Is the power supply connected?
(The display flashes in case of power failure)
Is the selector switch set to automatic (A)?
Check, if the programmed up and down times are still stored in the
memory by shortly tapping the up or down button in automatic
mode.
Is there a broken glass signal present?
(The display will indicate the broken glass symbol)
- 66 -
G
Troubleshooting

1. Switch off the power supply.
2. Set the DIP switches to the desired function (see pages 58, 59 and 61).
3. Push supporting frame through the cover frame and connect according to the
wiring diagram (see page 70).
4. Slide the control in the supporting frame and screw them together.
5. Switch on the power supply and press the reset button.
6. Set the selector switch to manual mode (H), i.e. push it to the right all the way
to the “click”. Check, if the ,5direction of the motor rotation corresponds with the
direction buttons. If not, exchange terminal 4 with terminal 5.
- 67 - G
Notes for professional electricians Installation
WARNING!
Risk of injury due to improper installation and commissioning.
Improper installation and commissioning may lead to personal injury
or property damage.
Therefore:
– When connecting the device, observe the currently valid VDE
standards (in particular DIN VDE 0100/0700), your local power
company’s regulations and the current accident prevention regu-
lations.
– Connect the control in accordance with the wiring diagram.
Ä
For surface-type installation
please use our surface-type housing, article-no. 01400250
For controlling two drives, we recommend our isolating relays:
Isolating relays MC TR 2A, article-no. 01054120
Isolating relays MC TR 2S, article-no. 01054220
Isolating relays MC TR 2S FMT, article-no. 01054230
Isolating relays MC TR 2S / MR, article-no. 01054520.
- 68 -
G
Installation Notes for professional electricians
IMPORTANT!
Parallel control of several roller shutter drive motors can
only be implemented by means of isolating relays or group
control devices.
In case of power failure, the display contrast will fade which
does not indicate that the battery is empty.
x

G
- 69 -
Power supply: 230VAC, 50 Hz
Impulse voltage withstand level: 2.5 kV
Rated power: 2 W
Output: 230VAC, 50 Hz
Maximum load: 250VAC, 3A, cos f > 0.8 ind.
Align switching time: 120 seconds
Software class: A
Operating temperature: 0 °C (32 °F) to +40 °C (104 °F)
IP class: IP 40
Degree of contamination: 2
Dimensions (L × W × H): 69 × 69 × 54 mm
Colour information: signal white (similar to RAL 9016)
Conformity: p
Installation instructions/Technical data Installation
G- 70 -
Installation Wiring diagram

G
The additional function “broken glass sensor” requires an extra
broken glass sensor for each control (for larger or separated window
panes). The installation of the lux sensor is described below.
1. Push the selector switch all the way to the right until it clicks to set
the manual mode to (H).
2. Mix binder and hardener of the two-component adhesive thor-
oughly in a 1 : 1 ratio.
- 71 -
Broken glass sensor Installation
3. Apply the adhesive to the side of the broken glass sensor that is
marked with a black bar.
4. Place broken glass sensor carefully onto to the window pane and
make sure to clear the window frame by minimum 2 inches. Attach
the broken glass sensor with adhesive tape and ensure that it
is located perpendicular with the cable going off to the bottom
(please refer to the picture on page 71).
5. Plug the lux sensor jack into the left-hand socket of the roller
shutter control.
6. Push the selector switch all the way to the left until it clicks to set
the automatic mode to (A).
7. Validity check:
Take a coin and tap the broken glass sensor with it in order to
simulate breaking glass. The roller shutter will now move down and
the display will indicate the broken glass symbol. Press the up button
to stop the roller shutter and delete the broken glass signal.
Remove the adhesive tape after the adhesive has hardened. Please
check the processing and hardening times for the use of the adhesive
with the instructions on the adhesive packaging.
- 72 -
G
Installation Broken glass sensor
IMPORTANT!
Make sure to keep the adhesive areas clean and oil-free.
x

G
The additional function “sun protection” requires an extra lux sensor
for each control. The installation of the lux sensor is described below.
1. Plug the lux sensor jack into the right-hand socket of the roller
shutter control.
2. Attach the lux sensor in the desired area of the window.
3. Push the selector switch all the way to the left until it clicks to set
the automatic mode to (A).
- 73 -
Lux sensor Installation
After completing the installation, activate the quick run function in
order to check the additional function “sun protection” by pressing the
time and day button simultaneously for 3 seconds (this will make the
time run 60 times faster). That way you can check the entire functional
sequence within a short amount of time.
Example of a test run:
1. Check whether you are within the range of the programmed up and
down times.
2. Press the time and day button simultaneously for 3 seconds.
3. Expose the lux sensor to light until the sun symbol flashes.
After approx. 1 second the shutter moves to the shade position.
Remove the light source.
The sun symbol in the display will flash again.
After 16 seconds, the roller shutter will move up again.
4. Press the time and day button shortly after the test run is com-
pleted.
5. Set the current time as described on page 48.
- 74 -
G
Installation Lux sensor

D G
Anschlussbild/Wiring diagram
Rolltec Plus G/S
D G
Übersicht Bedienungselemente/ Overview operating elements
Rolltec Plus G/S

Art.-Nr. 85601721 F1
Vestamatic GmbH
Dohrweg 27
D-41066 Mönchengladbach
[email protected]
www.vestamatic.com
Entsorgung / Disposal of waste
Die Entsorgung von Elektrogeräten und Batterien über
den Hausmüll ist verboten.
Das nebenstehende Symbol (durchgestrichene Mülltonne
nach WEEE Anhang IV) weist auf die getrennte Rücknahme
elektrischer und elektronischer Geräte in den EU-Ländern hin.
Werfen Sie das Gerät oder die Batterie nicht in den Haus-
müll, informieren Sie sich über Rückgabemöglichkeiten in
Ihrem Gebiet und nutzen Sie zur Entsorgung das Rückgabe-
system.
The disposal of electrical equipment and batteries in
household waste is strictly forbidden.
The symbol (dustbin crossed out, in line with WEEE Appendix
IV)
indicates separate collection of electrical and electronic
products in EU countries. Do not dispose of the device or
battery in your household waste. Ask your town or local
council about the return and collection systems available in
your area to dispose of this product.
Druckfehler, Irrtümer und Änderungen vorbehalten!
Printing errors and details are subject to change without notification.
© Vestamatic GmbH
É