Victaulic FireLock I-756 Series User manual

WARNING
Failure to follow instructions and warnings can cause product
failure, resulting in serious personal injury and property damage.
• Read and understand all instructions before attempting
to install, remove, adjust, or maintain any Victaulic piping
products.
• Depressurize and drain the piping system before attempting
to install, remove, adjust, or maintain any Victaulic piping
products.
• Wear safety glasses, hardhat, and foot protection.
If you need additional copies of any literature, or if you
have any questions concerning the safe use of this product,
contact Victaulic, P.O. Box 31, Easton, PA 18044-0031, USA,
Telephone: 1-800 PICK VIC, e-mail: [e-mail].
WARNING
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

TABLE OF CONTENTS
Hazard Identification ......................................1
Contents of Rebuild Kit ....................................1
Removing the System from Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Instructions for Replacing Internal Components of the Valve
(Items 1 - 10 on page 2) .................................3
Instructions for Replacing Internal Components of the Piston. . . . . . . . 9
Piston Components .....................................9
Disassembly of Piston ...................................9
Replacing the Shaft Seal in the Cylinder. . . . . . . . . . . . . . . . . . . . . 11
Re-Assembly of the Piston...............................13
HAZARD IDENTIFICATION
Definitions for identifying the various hazard levels are
provided below. When you see this symbol, be alert to the
possibility of personal injury. Carefully read and fully
u nderstand the message that follows.
WARNING
• The use of the word “WARNING” identifies the presence
of hazards or unsafe practices that could result in death or
serious personal injury if instructions, including recommended
precautions, are not followed.
CAUTION
• The use of the word “CAUTION” identifies possible hazards or
unsafe practices that could result in personal injury and product
or property damage if instructions, including recommended
precautions, are not followed.
NOTICE
• The use of the word “NOTICE” identifies special instructions
that are important but not related to hazards.
CONTENTS OF REBUILD KIT
11 10
9
9
8
8
7
1
2
3
4
5
6
15
13
14
16
17
12
SEE “EXPLODED PISTON
ASSEMBLY”
EXPLODED PISTON
ASSEMBLY
Internal Components of the Valve
Item Qty. Description
11Clapper Seal
21Seal Ring
3* 1Seal Washer
41Bolt Seal
51Clapper Shaft
61Latch Shaft
71Latch Spring
82Latch Spring Insertion Tool
92Spacer
10 1Cover Plate Gasket
11 1Clapper Spring
Internal Components of the Piston
Item Qty. Description
12 1Piston Shaft
13 1Diaphragm
14 1Compression Spring
15 1Washer for Piston Shaft Retaining Bolt
16 1O-Ring
17 1Shaft Seal
Additional Items Included with Kit (Not Shown in Drawing)
Item Qty. Description
–1Piston Shaft Protective Sleeve
–1Nye® Lubricants, Inc. 8531R Grease for Piston Shaft
* Item #3 is not applicable for 1 ½ – 2-inch/48.3 – 60.3-mm valve sizes.
I-756/758.RBKIT_1
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

REMOVING THE SYSTEM FROM SERVICE
WARNING
• Depressurize and the piping system before
attempting to disassemble any Victaulic piping
products.
Failure to follow this instruction could result in
serious personal injury and/or property damage.
WARNING
• Any activities that require taking the valve out of
service may eliminate the fire protection provided.
• Before servicing or testing the system, notify the
authority having jurisdiction.
• Consideration of a fire patrol should be given in
the affected areas.
Failure to follow these instructions could result in
serious personal injury and/or property damage.
1. Notify the authority having jurisdiction, remote station alarm
monitors, and those in the affected area that the system is being
taken out of service.
Water Supply's
Main Control
Valve
2. Close the water supply’s main control valve to take the system out
of service.
Water Supply
Main Drain
Valve
3. Open the water supply main drain valve, as shown above.
4. Confirm that no water is flowing from the water supply main drain.
Piston
Charge Line
Ball Valve
5. Close the piston charge line ball valve.
System Main
Drain Valve
6. Open the system main drain valve to drain any water that has
accumulated and to release system air pressure. NOTE: If
the system has operated, open the remote system test valve
(inspector’s test connection) and any auxiliary drain valves.
Slow Fill
Ball Valve
7. Close the slow fill ball valve on the Air Maintenance Trim Assembly
(AMTA).
I-756/758.RBKIT_2
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

INSTRUCTIONS FOR REPLACING INTERNAL
COMPONENTS OF THE VALVE
(ITEMS 1 - 10 ON PAGE 1)
WARNING
• Make sure valve is depressurized and drained
before removing cover plate bolts.
The cover plate will blow off if these bolts are
removed while the valve is pressurized, resulting in
serious personal injury and/or property damage.
1. Make sure all instructions in the “Removing the System from
Service” section have been followed.
2. After all pressure is released from the system, loosen the cover
plate bolts. Remove the cover plate, and discard the cover plate
gasket.
3. Remove the clapper-shaft retaining plugs from the valve body.
4. Remove the clapper shaft, as shown above. NOTE: As the shaft is
being removed, the two spacers and clapper spring will drop out of
position. Discard the two spacers and the clapper spring.
5. Remove the clapper assembly from the valve body.
6. Remove the latch-shaft retaining plugs from the valve body.
I-756/758.RBKIT_3
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

WARNING
• DO NOT allow the latch to drop onto the valve-body seat ring.
Failure to follow this instruction will damage the valve-body seat
ring and cause improper valve operation, resulting in serious
personal injury and/or property damage.
7. Remove the latch shaft. NOTE: As the latch shaft is being
removed, the latch and latch spring will drop out of position. BE
PREPARED TO SUPPORT THE LATCH AND LATCH SPRING
DURING REMOVAL OF THE LATCH SHAFT. DO NOT ALLOW
THE LATCH TO DROP ONTO THE VALVE-BODY SEAT RING.
Discard the latch shaft and latch spring. Save the latch for
re-installation.
WARNING
• Make sure the latch is re-installed in the correct orientation.
Failure to re-install the latch in the correct orientation could
cause improper valve operation, resulting in serious personal
injury and/or property damage.
This Side Must
Face Toward
Piston
This Side Must
Face Toward
Outside of Valve
8. Insert the new latch shaft (supplied with the kit) through the
valve body and into the first arm of the shaft. MAKE SURE THE
FLAT, ANGLED SIDE OF THE LATCH IS FACING OUTWARD, AS
SHOWN ABOVE. THE SIDE OF THE LATCH THAT CONTAINS A
RECESS MUST FACE THE PISTON.
9. Place a spring insert tool (supplied with the kit) onto each arm of
the new latch spring (supplied with the kit). Using the spring insert
tool to close the latch spring arms together slightly, install the latch
spring onto the latch shaft, as shown above.
I-756/758.RBKIT_4
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

10. Continue to pass the latch shaft through the other arm of the latch
and valve body.
11. REMOVE THE SPRING INSERT TOOLS FROM THE ARMS OF
THE LATCH SPRING.
12. Apply thread sealant to the threads of the latch-shaft retaining
plugs. Install the latch-shaft retaining plugs into the valve body.
13. Place the clapper assembly onto the valve-body seat ring so that
the holes in the clapper arms align with the holes in the valve
body, as shown above.
14. Start the new clapper shaft (supplied with the kit) into the valve
body, and place one new spacer (supplied with the kit) between
the clapper and valve body, as shown above.
15. Install the new clapper spring (supplied with the kit) onto the
clapper shaft. Make sure the large loop is facing toward the
clapper, as shown above. The two small loops on the other end of
the spring must face upward.
16. Place the other new spacer (supplied with the kit) between
the other clapper arm and valve body, as shown above. Finish
inserting the clapper shaft through the clapper arm and valve
body. NOTE: To prevent damage to the spacers, care must be
taken during alignment.
I-756/758.RBKIT_5
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

17. Apply thread sealant to the threads of the clapper-shaft retaining
plugs. Install the clapper-shaft retaining plugs into the valve body.
18. Check the clapper for freedom of movement.
19. Rotate the clapper out of the valve body. Remove the seal-
assembly bolt/bolt seal from the clapper seal, as shown above.
Save the seal assembly bolt for re-installation. Discard the bolt
seal.
20. Remove the seal-retaining ring. Save the seal-retaining ring for
re-installation.
21. Pry the edge of the old seal washer from inside the clapper seal.
Remove and discard the seal washer.
22. Pry the old clapper seal, along with the seal ring, out of the
clapper. Discard the clapper seal and seal ring.
I-756/758.RBKIT_6
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

23. Install the new clapper seal assembly (supplied with the kit) into
the clapper carefully. Make sure the seal ring snaps into the
clapper completely.
24. Place the seal-retaining ring onto the seal washer of the clapper
seal.
25. Install the new bolt seal (supplied with the kit) onto the seal-
assembly bolt.
26. Install the seal-assembly bolt/bolt seal through the seal-retaining
ring and clapper. Tighten the seal-assembly bolt/bolt seal to the
torque value, listed in the table below, to ensure a proper seal.
REQUIRED SEAL-ASSEMBLY BOLT/BOLT SEAL TORQUES
Size Torque
Nominal Size
inches
Actual
Outside Diameter
inches/mm
inch-lbs
N•m
1 ½ 1.900 40
48.3 5
22.375 40
60.3 5
2 ½ 2.875 90
73.0 10
76.1 mm 3.000 90
76.1 10
33.500 90
88.9 10
44.500 110
114.3 12
165.1 mm 6.500 160
165.1 18
66.625 160
168.3 18
88.625 160
219.1 18
27. Align the holes of the new cover plate gasket (supplied with the kit)
with the holes in the cover plate.
I-756/758.RBKIT_7
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

28. Insert one cover plate bolt through the cover plate and cover plate
gasket to ease alignment.
CAUTION
• DO NOT over-tighten the cover plate bolts.
Failure to follow this instruction could cause damage to the
cover plate gasket, resulting in valve leakage.
29. Align the cover plate/cover plate gasket to the valve. Make sure the
clapper spring’s arms are rotated to their installed position. Tighten
all cover plate bolts into the cover plate/valve body.
29a. Torque all cover plate bolts in an even, crossing pattern. Refer to
the “Required Cover Plate Bolt Torques” table on this page for the
required torque values. DO NOT over-tighten the cover plate bolts.
Required Cover Plate Bolt Torques
Size Torque
Nominal Size
inches or mm
Actual
Outside Diameter
inches
mm
ft-lbs
N•m
1 ½ 1.900 30
48.3 41
22.375 30
60.3 41
2 ½ 2.875 60
73.0 81
76.1 mm 3.000 60
76.1 81
33.500 60
88.9 81
44.500 100
114.3 136
165.1 mm 6.500 115
165.1 156
66.625 115
168.3 156
88.625 100
219.1 136
I-756/758.RBKIT_8
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

INSTRUCTIONS FOR REPLACING INTERNAL
COMPONENTS OF THE PISTON
PISTON COMPONENTS
3
1
2
5
8
11
14
15
46
7
9
10
12 13
Item Description
1 Socket Head Cap Screw
2 Bonnet
3 Piston Shaft Retaining Bolt
4* Washer for Piston Shaft Retaining Bolt
5 Diaphragm Retainer
6* Diaphragm
7 Piston
8* Compression Spring
9 Cylinder
10* O-Ring
11 Bearing
12* Shaft Seal
13 O-Ring
14 Seal Retainer
15* Piston Shaft
* Components denoted with an asterisk are provided in the kit.
DISASSEMBLY OF PISTON
WARNING
• Make sure the valve is depressurized and
drained before attempting to remove any trim
from the valve.
Failure to depressurize and drain the valve before
removing any trim from the valve could cause
serious personal injury and/or property damage.
If the system is in service, follow the “Removing the System from
Service” section.
1. Disconnect the trim from the piston.
2. Remove the piston from the valve body.
CAUTION
• Wear safety glasses when performing the
following steps. The piston contains a
compression spring, which may release when
the bonnet is removed.
Failure to follow this instruction could result in
personal injury.
3. Remove the six socket head cap screws from the bonnet. Save the
six socket head cap screws for re-installation. NOTE: Since the
piston contains a compression spring, be prepared to support the
bonnet when the last socket head cap screw is removed.
Socket Head Cap Screw Sizes
Valve Size
Socket Head Cap
Screw Size
Nominal Size
inches
Actual Outside Diameter
inches/mm
1½ – 4 1.900 – 4.500 8 – 32 x ⁄
48.3 – 114.3
6 – 8 6.625 – 8.625 ¼ – 20 x ¾
168.3 – 219.1
I-756/758.RBKIT_9
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

4. Remove the bonnet from the cylinder to expose the internal
assembly. Save the cylinder for re-installation.
5. Remove the compression spring and bonnet. Save the bonnet for
re-installation. Discard the compression spring.
6. Using a wrench on the flats of the piston shaft, remove the piston-
shaft retaining bolt from the diaphragm retainer, as shown above.
Save the piston-shaft retaining bolt for re-installation. Discard the
piston shaft.
7. Remove the washer from the piston-shaft retaining bolt. Discard
the washer.
8. Remove the diaphragm retainer. Save the diaphragm retainer for
re-installation.
9. Remove the diaphragm from the piston. Save the piston for
re-installation. Discard the diaphragm.
I-756/758.RBKIT_10
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

REPLACING THE SHAFT SEAL IN THE CYLINDER
1. Using a spanner wrench or similar device, remove the seal retainer
from the cylinder. NOTE: For smaller-size pistons, a spanner
wrench may need to be modified to fit into the holes of the seal
retainer.
2. Remove the o-ring from the seal retainer. Save the o-ring for
re-installation.
3. Remove the shaft seal from the seal retainer. Discard the shaft
seal.
4. Clean the area of the seal retainer where the shaft seal and o-ring
seat.
I-756/758.RBKIT_11
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

Coil Side
5. Install the new shaft seal (supplied with the kit) into the seal
retainer. Make sure the coil side of the shaft seal faces the seal
retainer, as shown above.
6. Re-install the o-ring into the seal retainer.
CAUTION
• DO NOT turn the seal retainer upside down to place it inside
the cylinder.
The shaft seal and o-ring could fall out of position and become
damaged during re-assembly, resulting in piston leakage.
7. While holding the seal retainer with the shaft seal and o-ring facing
up, place the cylinder on top of the seal retainer. DO NOT turn the
seal retainer upside down to place it inside the cylinder. The shaft
seal and o-ring could fall out of position and become damaged
during re-assembly. Maintain this position until the seal retainer is
tightened completely into the cylinder in the next step.
8. Using a spanner wrench or similar device, re-install the seal
retainer into the cylinder and tighten completely.
I-756/758.RBKIT_12
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

RE-ASSEMBLY OF THE PISTON
1. Turn the new diaphragm (supplied with the kit) inside out so that
the smooth, rubber side is facing outward and the fabric side is
facing inward (toward the piston).
2. Place the new diaphragm over the piston. MAKE SURE THE
FABRIC SIDE OF THE DIAPHRAGM CONTACTS THE PISTON.
3. Install the new washer (supplied with the kit) onto the piston-shaft
retaining bolt.
4. Install the diaphragm retainer onto the piston with the piston-shaft
retaining bolt. Install the new piston shaft (supplied with the kit)
onto the piston-shaft retaining bolt.
5. Using a smooth-sided wrench on the flats of the piston shaft for
support, tighten the piston-shaft retaining bolt, as shown above.
Be careful not to damage the piston shaft. DO NOT use a pipe
wrench, vise grips, or any other tool that contains teeth on the
piston shaft.
6. Fold the diaphragm so that the lip is flush with the end of the
diaphragm retainer, as shown above.
7. LUBRICATE THE PISTON SHAFT WITH THE GREASE
PROVIDED IN THE KIT (Nye® Lubricants, Inc. 8531R Grease).
I-756/758.RBKIT_13
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

8. Install the new compression spring (supplied with the kit) over the
piston shaft so that the compression spring seats within the piston.
CAUTION
• DO NOT damage the shaft seal during assembly.
Damage to the shaft seal could cause the piston to operate
improperly, resulting in property damage.
9. Install the piston assembly into the cylinder so that the diaphragm
retainer is flush with the end of the cylinder. Be careful not to
damage the shaft seal.
10. While holding the piston assembly in position, install the piston-
shaft protective sleeve (supplied with the kit) over the end of the
piston shaft, as shown above. This protective sleeve will prevent
damage to the piston shaft during the next few steps.
11. Using a pair of vise grips, maintain the extended position of the
piston shaft, as shown above. Tighten the vise grips just enough to
hold the extended position. DO NOT over-tighten the vise grips.
12. Make sure the holes in the diaphragm align with the holes in the
cylinder, as shown above.
13. Align the holes of the bonnet with the holes of the cylinder/
diaphragm.
I-756/758.RBKIT_14
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKIT
REBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

14. Install the six socket head cap screws into the bonnet/cylinder.
Tighten the screws evenly in a crossing pattern.
15. Remove the vise grips from the piston shaft. NOTE: The piston
shaft will retract to its normal position. Make sure the piston-shaft
protective sleeve is removed from the end of the piston shaft.
CAUTION
• DO NOT extend the piston manually. Manually extending the
piston could damage the internal diaphragm.
Failure to follow this instruction could cause improper valve
operation, resulting in property damage.
O-Ring
16. Remove the o-ring from the piston. Discard the old o-ring, and
replace it with the new o-ring (supplied with the kit).
17. Clean the back of the valve body to remove any debris that may
interfere with proper piston seating.
18. Re-install the piston into the back of the valve body. Tighten the
piston until it comes into metal-to-metal contact with the valve
body.
CAUTION
• Make sure the piston is assembled and
installed correctly.
Failure to follow this instruction could
improper valve operation, resulting in
property damage.
19. Re-attach the trim. Refer to the applicable trim drawing for
complete details.
20. Place the system back in service by following the “Placing
the System in Service” section in the applicable installation,
maintenance, and testing manual for the valve.
I-756/758.RBKIT_15
5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_B

5-Year Rebuild Kit Instructions for FireLock®
Dry, Deluge, and Preaction Valves
SERIES 756 AND 758
I-756/758.RBKITREBUILD KIT INSTRUCTIONS
I-756/758.RBKIT
For complete contact information, visit www.victaulic.com
I-756/758.RBKIT 4085 REV B UPDATED 03/2010 Z0005RBKIT
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.