Victaulic 751 FireLock Series User manual

R
Installation,
Maintenance, & Testing Manual
Series 751
FireLock
®
European
Alarm Check Valve Stations
Hang these instructions on the
installed valve for easy future reference.
WARNING
Failure to follow instructions and warnings could cause product failure, resulting in serious personal injury and/or property
damage.
• Read and understand all instructions before attempting to install, maintain, or test any Victaulic piping products.
• Wear safety glasses, hardhat, and foot protection.
If you need additional copies of any literature, or if you have any questions about the safe installation and operation of this
product, contact Victaulic Company of Europe, Prijkelstraat 36, 9810 Nazareth, Belgium, Phone: [phone].
VdS
0786

Series 751 FireLock
®
European Alarm Check Valve Stations
1
TABLE OF CONTENTS
Hazard Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installer Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Trim Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Exploded View Drawing – Trim Components . . . . . . . . . . . . .4
Exploded View Drawing – Internal Valve Components . . . . . .5
Important Installation Information . . . . . . . . . . . . . . . . . . . . . .5
Placing the System in Service . . . . . . . . . . . . . . . . . . . . . . . . .6
External Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Monthly Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Required Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Main Drain Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Water Flow Alarm Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Required Internal Inspection . . . . . . . . . . . . . . . . . . . . . . . . .10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Removing and Replacing Clapper Seal for
DN 100 and DN 150 Size Valves . . . . . . . . . . . . . . . . . . . .12
Removing and Replacing Clapper Assembly . . . . . . . . . .13
Installing Cover Plate Gasket and Cover Plate . . . . . . . . . 14
Troubleshooting – Series 751 Alarm Check Valve . . . . . . . . .16
Facilities Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B/C
HAZARD IDENTIFICATION
Definitions for identifying the various hazard levels are provided
below.
This safety alert symbol indicates important safety
messages. When you see this symbol, be alert to
the possibility of personal injury. Carefully read and
fully understand the message that follows.
WARNING
The use of the word “WARNING” identifies the presence
of hazards or unsafe practices that could result in death
or serious personal injury if instructions, including rec-
ommended precautions, are not followed.
CAUTION
The use of the word “CAUTION” identifies possible haz-
ards or unsafe practices that could result in personal
injury and product or property damage if instructions,
including recommended precautions, are not followed.
NOTICE
The use of the word “NOTICE” identifies special
instructions that are important but not related to
hazards.

Series 751 FireLock
®
European Alarm Check Valve Stations
2
INSTALLER SAFETY INSTRUCTIONS
General
1. Read and understand all instructions before proceed-
ing with the installation, maintenance, and testing of this
Victaulic fire protection device.
2. Use only recommended accessories. Use of improper
accessories or equipment could result in improper system oper-
ation.
3. Avoid dangerous environments. If using electrically
powered tools for installation, make sure the area is moisture-
free. Keep work areas well lit. Allow enough space for installing
the device, trim, and accessories safely and efficiently.
4. Prevent back injury. Larger and pre-trimmed valves are
heavier and may require more than one person or mechanical
lifting equipment to position and install the assembly properly.
Always practice proper lifting techniques.
5. Inspect the shipment. Make sure all components are in-
cluded with the shipment and that all necessary tools are avail-
able for proper installation.
6. Wear safety glasses, hardhat, foot protection, and
hearing protection. Protect your hearing if you are exposed to
long periods of very noisy job-site operations.
7. Watch for pinch points. Do not put fingers under the
valve body where they could be pinched by the weight of the
valve. Use caution around spring-loaded components (i.e. clap-
per).
8. Keep work areas clean. Cluttered areas, benches, and
slippery floors can create hazardous working conditions.
9. Keep visitors away. Keep all visitors a safe distance
away from work areas.
Maintenance and Testing
1. Notify the authority having jurisdiction. Always notify
the authority having jurisdiction before taking a fire protection
system out of service or before performing any maintenance that
eliminates the fire protection provided by the system.
2. Depressurize and drain the system completely before
performing any maintenance. Water under pressure, trapped
air, or system air pressure may be present and can create haz-
ardous conditions.
3. Contact the local authority having jurisdiction for test-
ing and inspection schedules.
4. Keep the system away from freezing, corrosive atmos-
pheres, and foreign matter. Any condition that might degrade
the system or affect system performance must be avoided.
WARNING
• An experienced, trained installer must install this product in accordance with all instructions. These instructions contain
important information.
Failure to follow these instructions could cause product failure, resulting in serious personal injury and/or property damage.
If you need additional copies of any literature, or if you have any questions about the safe installation and operation of this
product, contact Victaulic Company of Europe, Prijkelstraat 36, 9810 Nazareth, Belgium, Phone: [phone].
WARNING
• Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products.
Failure to follow this instruction could cause product failure, resulting in serious personal injury and/or property damage.

Series 751 FireLock
®
European Alarm Check Valve Stations
3
INTRODUCTION
The following instructions are a guide for proper installation of Victaulic Series 751 Alarm Check Valves. These instructions involve pipe
that is properly prepared and grooved in accordance with current Victaulic specifications.
TRIM DIMENSIONS
Valve
Size
Dimensions – centimeters Approx.
Weight
Each
kgA* A
1
BB
1
CDEFGH I JK
DN100 38,18 50,66 59,00 202,00 16,13 22,33 24,45 28,68 7,00 19,33 33,00 33,00 7,22 54,0
DN150 40,64 56,32 61,00 206,00 18,60 25,48 33,00 38,00 – 20,30 36,00 38,00 3,20 69,0
*The “A” dimension is the measurement from the top of the valve body to the bottom of the valve body (takeout dimension).
NOTE: Overall height “B” is greatest height if optional retard chamber is not installed.
EF
C D H
A
A1
B1
B
J I
G
K

Series 751 FireLock
®
European Alarm Check Valve Stations
4
EXPLODED VIEW DRAWING – TRIM COMPONENTS
Series 751 FireLock™ European Alarm Check Valve Stations
(Optional Accessories Also Shown)
Grooved X Grooved
WATER MOTOR
ALARM
SERIES 760
150
F
³⁄₄
UL
C
FM
LISTED
To Drain
Water
Supply
9
16
7
11
1
8
4
2
6
5
10
14
13
15
4
3
12
BILL OF MATERIALS
1 Series 751 FireLock European Alarm Check Valve 10 EPS-10 Alarm Pressure Switch
2 Style 005 FireLock Rigid Coupling 11 Alarm Line Ball Valve (Lockable - Normally Open)
3 Series 705W Butterfly Valve 12 Series 760 Water Motor Alarm
4 Gauge Valve with ³⁄₄-inch Strainer - 100 mesh (Optional)
5 Water Supply Pressure Gauge (0-25 Bar) 13 Series 752 Retard Chamber (Optional)
6 Swing Check Valve 14 System Main Drain Valve
7 Restricted Orifice/Alarm Line Drain 15 System Test Valve
8 Reducer 16 System Pressure Gauge (0-25 Bar)
9 Reducing Bushing
To
System
Normally
Open
(Lockable)
Optional
Retard
Chamber

Series 751 FireLock
®
European Alarm Check Valve Stations
5
EXPLODED VIEW DRAWING – INTERNAL VALVE COMPONENTS
IMPORTANT INSTALLATION INFORMATION
1. Before installing the Series 751 Alarm Check Valve, flush
the water supply piping thoroughly to ensure that no foreign ma-
terial is present.
2. The Series 751 Alarm Check Valve MUST NOT be located
in an area where the valve is subject to freezing temperatures or
physical damage.
3. It is the owner’s responsibility to confirm material compat-
ibility of the Series 751 Alarm Check Valve, trim, and associated
accessories when a corrosive environment or contaminated wa-
ter is present.
4. Series 751 Alarm Check Valves MUST be installed in the
vertical position only. The arrow on the body must point upward,
and the arrow on the swing check valve in the bypass line must
point upward.
5. The Series 752 Retard Chamber should be installed in
variable pressure applications. Victaulic provides specific trim
drawings for installations that involve a Series 752 Retard Cham-
ber.
6. Confirm that all installation information is available.
7. Remove all plastic caps and foam spacers from the valve.
8. Install the Victaulic Series 751 Alarm Check Valve in ac-
cordance with the applicable trim drawings. Make sure the trim
drawing matches the system’s requirements (i.e. retard cham-
ber for variable pressure installations).
BILL OF MATERIALS
1 Valve Body 7 Seal-Retaining Ring
2 Clapper Shaft Retaining Bushing (Qty. 2) 8 Bolt Seal
3 Clapper Shaft 9 Seal Assembly Bolt
4 Clapper 10 Cover Plate Gasket
5 Clapper Spring 11 Cover Plate
6 Clapper Seal 12 Cover Plate Bolts (Qty. 7)
1
12
11
4
3
2
10
6
7
9
5
8
CAUTION
• Make sure foam spacers are removed before
attempting to install the valve.
Failure to follow this instruction could cause
improper valve operation, resulting in serious per-
sonal injury and/or property damage.

Series 751 FireLock
®
European Alarm Check Valve Stations
6
PLACING THE SYSTEM IN SERVICE
1. Confirm that system drains are shut and the system is free
of leaks.
2. Open the auxiliary drains.
3. Close the alarm line ball valve (11) to prevent alarms from
operating while the system is filling. Alarms and electrical panels
(controlled by an alarm flow switch on the riser) cannot be inter-
rupted. NOTE: If alarm activation is possible, notify local fire
companies that the system is being serviced.
4. Open the water supply’s main control valve (3) slowly.
4a. Allow the system to fill with water completely. Allow water
to flow from the auxiliary drains to release all trapped air from the
system.
4b. When a steady flow of water occurs and all air is released
from the system, close the auxiliary drains in the system.
4c. Record the system pressures. The system pressure
gauge (16) should be equal to or greater than the water supply
pressure gauge (5).
5. Open the alarm line ball valve (11). Lock the ball valve, as
required.
6. Confirm that all valves are in their normal operating posi-
tions.
7. Notify the authority having jurisdiction, remote station
alarm monitors, and those in the affected area that the system is
in service.
CAUTION
• Make sure the Series 751 Alarm Check Valve is properly heated and
protected from freezing temperatures and physical damage.
Failure to follow these instructions could cause improper valve operation,
resulting in personal injury and/or property damage.
CAUTION
• For proper operation of alarms in a wet system, it is important to ensure
that all air is removed from the system. Auxiliary vents may be required to
release all trapped air from the system.
Failure to follow these instructions could cause improper valve operation,
resulting in personal injury and/or property damage.
CAUTION
• Take precautions when opening the water supply’s main control valve,
since water will flow from all open system valves.
Failure to follow this instruction could cause personal injury and/or property
damage.
11
3
CAUTION
• The alarm line ball valve must be open to allow alarms to activate.
Failure to follow this instruction will prevent alarms to activate, resulting in
serious personal injury and/or property damage.
11

Series 751 FireLock
®
European Alarm Check Valve Stations
7
EXTERNAL INSPECTION
Monthly Inspection
Victaulic recommends a visual inspection of the alarm check
valve and trim on a monthly basis.
1. Record the system’s pressure and the water supply’s
pressure. It is normal for the system’s water pressure to be high-
er than the water supply’s pressure due to the check valve trap-
ping pressure surges above the clapper. Confirm that the water
supply’s pressure is in the range of normal pressures observed
in the area. A significant loss in supply pressure could indicate
an adverse condition in the water supply.
2. Check for mechanical damage or corrosion. If damage or
corrosion is present, replace the affected parts.
3. Confirm that the valve and trim are not subject to freezing
conditions.
4. If the valve is installed in a variable pressure system, con-
firm that no excessive leakage is occurring from the restricted
orifice/alarm line drain. It is normal for some leakage, since pres-
sure surges lift the clapper and allow water into the intermediate
chamber.
5. Verify that all valves are in their normal operating positions.
REQUIRED TESTS
Main Drain Test
The authority having jurisdiction in your area may require the
main drain test on a more frequent basis. Verify these require-
ments by contacting the authority having jurisdiction in your
area.
1. Notify the authority having jurisdiction, remote station
alarm monitors, and anyone in the affected area that the main
drain test will be performed.
2. Confirm that sufficient drainage is in place for a full-flow
drain test.
3. Record the water supply pressure.
4. Close the alarm line ball valve (11).
5. Open the system main drain valve (14) fully.
5a. With the system main drain valve fully open, record the
water supply pressure as the residual pressure.
CAUTION
• Any activities that require taking the valve out of
service may eliminate the fire protection provided.
• Before servicing or testing the system, notify the
authority having jurisdiction.
• Consideration of a fire patrol should be given in the
affected areas.
Failure to follow these instructions could cause seri-
ous personal injury and/or property damage.
NOTICE
• The owner is responsible for maintaining the fire protection system in
proper operating condition.
• It is important that the system is inspected regularly, according to proper
procedures.
• The Victaulic Series 751 Alarm Check Valve and trim must not be exposed
to foreign material, corrosive environments, freezing conditions, contami-
nated water supplies, or any other condition that could impair proper sys-
tem operation.
• Modify the frequency of inspections in the presence of any environmental
conditions that could degrade system operation.
• The authority having jurisdiction may have additional maintenance, inspec-
tion, and test requirements.
NOTICE
• If you do not want to activate alarms, close the alarm line ball valve
11
14

Series 751 FireLock®European Alarm Check Valve Stations
8
6. Close the system main drain valve (14) slowly.
6a. Record the water pressures established after closing the
system main drain valve.
6b. Compare the residual pressure reading, taken above, to
the residual pressure readings taken in previous main drain
tests. If there is degradation in the residual water supply read-
ings, restore the proper water supply pressure.
7. Open the alarm line ball valve (11), and make sure all
valves are in their proper operating positions.
8. Notify the authority having jurisdiction, remote station
alarm monitors, and those in the affected area that the valve is
back in service. Provide test results, as required, to the authority
having jurisdiction.
Water Flow Alarm Test
The authority having jurisdiction in your area may require the wa-
ter flow alarm test on a more frequent basis. Verify these require-
ments by contacting the authority having jurisdiction in your
area.
1. Notify the authority having jurisdiction, remote station
alarm monitors, and anyone in the affected area that the water
flow alarm test will be performed.
2. Verify that the alarm line ball valve (11) is open.
3. Open the system test valve (15) fully, as shown above.
Confirm that mechanical and electrical alarms are activated.
Confirm that remote monitoring stations, if provided, receive an
alarm signal. NOTE: There may be a time delay if a retard cham-
ber (13) is installed in the trim assembly.
4. Close the system test valve (15) after proper operation of
all alarms is verified.
5. Verify that all alarms stopped sounding, that the alarm line
drained properly, and that remote station alarms reset properly.
CAUTION
• The alarm line ball valve must be open to allow alarms to activate.
Failure to follow this instruction will prevent alarms to activate, resulting in
serious personal injury and/or property damage.
14
11
11
15
15

Series 751 FireLock®European Alarm Check Valve Stations
9
6. Push in the plunger on the restricted orifice/alarm line
drain (7), as shown above.
7. Verify that no water is flowing from the restricted orifice/
alarm line drain (7).
8. Notify the authority having jurisdiction, remote station
alarm monitors, and those in the affected area that the valve is
back in service.
9. Provide test results to the authority having jurisdiction, if
required.
7

Series 751 FireLock®European Alarm Check Valve Stations
10
REQUIRED INTERNAL INSPECTION
The authority having jurisdiction in your area may have estab-
lished requirements for internal inspection frequencies. Verify
these requirements by contacting the authority having jurisdic-
tion in your area.
1. Notify the authority having jurisdiction, remote station
alarm monitors, and those in the affected area that the system is
being taken out of service.
2. Close the water supply’s main control valve (3) to take the
system out of service.
3. Open the system main drain valve (14), and allow the sys-
tem to drain completely. It may be necessary to open the auxil-
iary drains in order to drain the system completely.
4. After all pressure is released from the system, remove all
cover plate bolts slowly.
4a. Remove the cover plate and cover plate gasket.
WARNING
• Depressurize and drain the piping system
before attempting to install, remove, or adjust
any Victaulic piping products.
Failure to follow this instruction could cause
serious personal injury and/or property damage.
CAUTION
• Any activities that require taking the valve out of
service may eliminate the fire protection provided.
• Before servicing or testing the system, notify the
authority having jurisdiction.
• Consideration of a fire patrol should be given in
the affected areas.
Failure to follow these instructions could cause seri-
ous personal injury and/or property damage.
3
14
WARNING
• Make sure the valve is depressurized and
drained before removing the cover plate
bolts.
The cover plate could blow off if these bolts are
removed while the valve is pressurized, result-
ing in serious personal injury and/or property
damage.
CAUTION
• DO NOT use solvents or abrasives on or near the valve body seat ring.
Failure to follow this instruction could prevent the clapper from sealing prop-
erly, resulting in improper operation, valve leakage, and/or property damage.

Series 751 FireLock®European Alarm Check Valve Stations
11
5. Rotate the clapper out of the valve body. Inspect the clap-
per seal and seal-retaining ring. Wipe away any contaminants,
dirt, and mineral deposits. Clean any holes in the valve body
seat ring that are plugged. DO NOT USE SOLVENTS OR
ABRASIVES.
6. Inspect the clapper for freedom of movement and physi-
cal damage. Replace any damaged or worn parts by following
the applicable instructions in the “Maintenance” section, starting
on page 12.
7. Re-install the cover plate by following the “Installing Cover
Plate Gasket and Cover Plate” section, starting on page 14.

Series 751 FireLock®European Alarm Check Valve Stations
12
MAINTENANCE
The following steps instruct on how to remove and replace inter-
nal valve components. It is important that care be taken to avoid
damage to parts.
Removing and Replacing Clapper Seal for
DN 100 and DN 150 Size Valves
1. Perform steps 1 – 4 of the “Required Internal Inspection”
section, starting on page 10.
2. Remove the seal assembly bolt/bolt seal from the clapper,
as shown above.
3. Remove the seal-retaining ring. This seal-retaining ring will
need to be re-installed in later steps.
4. Remove the solid seal from the clapper and discard.
5. Make sure the clapper is free of contaminants, dirt, and
mineral deposits. Clean any holes in the valve body seat ring
that are plugged. DO NOT USE SOLVENTS OR ABRASIVES.
6. Install the new solid seal into the clapper, as shown above.
NOTE: Make sure the sealing lip is pointing upward.
WARNING
• Depressurize and drain the piping system
before attempting to install, remove, or
adjust any Victaulic piping products.
Failure to follow this instruction could cause
serious personal injury and/or property dam-
age.
CAUTION
• Any activities that require taking the valve out of
service may eliminate the fire protection pro-
vided.
• Before servicing or testing the system, notify the
authority having jurisdiction.
• Consideration of a fire patrol should be given in
the affected areas.
Failure to follow these instructions could cause
serious personal injury and/or property damage.
CAUTION
• DO NOT use solvents or abrasives on or near the valve body seat ring.
Failure to follow this instruction could prevent the clapper from sealing prop-
erly, resulting in improper valve operation, valve leakage, and/or property
damage.

Series 751 FireLock®European Alarm Check Valve Stations
13
7. Place the seal-retaining ring onto the solid seal, as shown
above.
8. Install the seal assembly bolt/bolt seal through the seal-
retaining ring and the clapper. Tighten the seal assembly bolt/
bolt seal completely, and apply an additional ¹⁄₄ turn to ensure a
proper seal.
9. Replace the cover plate by following the “Installing Cover
Plate Gasket and Cover Plate” section, starting on page 14.
Removing and Replacing Clapper
Assembly
1. Perform steps 1 – 4 of the “Required Internal Inspection”
section, starting on page 10.
2. Remove one clapper shaft retaining bushing from the
valve body.
3. Remove the clapper shaft, as shown above. NOTE: As the
shaft is being removed, the clapper spring will drop out of posi-
tion. Keep the clapper spring for re-installation.
4. Remove the clapper from the valve body.
CAUTION
• Use only Victaulic-supplied replacement seal assembly bolt/ bolt seal when
reassembling the clapper.
Failure to follow this instruction could cause improper sealing, resulting in
valve leakage and/or property damage.

Series 751 FireLock®European Alarm Check Valve Stations
14
5. Place the new clapper assembly onto the valve body seat
ring so that the holes in the clapper arms align with the holes in
the valve body, as shown above.
6. Start the clapper shaft into the valve body, and install the
spring onto the clapper shaft. Make sure the loop is toward the
clapper, as shown above.
7. Install the clapper shaft retaining bushing into the valve
body.
8. Check the clapper for freedom of movement.
9. Replace the cover plate by following the “Installing Cover
Plate Gasket and Cover Plate” section, starting on this page.
Installing Cover Plate Gasket and Cover
Plate
1. Verify that the cover plate gasket is in good condition. If
the gasket is torn or worn, replace it with a new, Victaulic-sup-
plied gasket.
2. Align the cover plate gasket holes with the cover plate
holes.
3. Insert one cover bolt through the cover plate and cover
gasket to ease alignment.
4. Align the cover plate/cover plate gasket to the valve. Make
sure the spring arms are rotated to the installed position. Insert
all cover bolts and hand-tighten.
CAUTION
• DO NOT over-tighten the cover bolts.
Failure to follow this instruction could cause damage to the cover plate gas-
ket, resulting in valve leakage and/or property damage.

Series 751 FireLock®European Alarm Check Valve Stations
15
5. Torque all cover bolts in an even, crossing pattern. Refer
to the “Cover Bolt Torque Requirements” chart on this page for
the required torque values. DO NOT over-tighten the cover
bolts.
Cover Bolt Torque Requirements
6. Place the system back in service by following the “Placing
the System in Service” section, starting on page 6.
Valve
Size
Torque
N•m
DN 100 136
DN 150 156

Series 751 FireLock®European Alarm Check Valve Stations
16
TROUBLESHOOTING – SERIES 751 ALARM CHECK VALVE
Problem Possible Cause Solution
The system water pressure gauge is fluctuating with the supply
pressure.
The check valve in the bypass line is installed backward. Check the orientation of the bypass check valve. The arrow must point
from the supply side to the system side.
Debris is present in the bypass check valve. Remove the threaded cap to the check valve, and remove any debris.
Make sure the clapper is free to move.
Water is leaking from the intermediate chamber. Water is getting past the seal. Check the clapper seal and seat for physical damage. Make sure no
debris is present.
The water motor gong is not ringing, or the ringing is weak. No water is going into the intermediate chamber. Make sure the holes in the seat ring are not plugged.
Water from the alarm line could be leaking out of the alarm line drain of
another valve.
Make sure there are check valves isolating the alarm line of each valve.
The wrong restrictor size is installed in the alarm line drain. Confirm that the proper restrictor size is on the alarm drain. If not, re-
install the proper size restrictor, according to the trim drawing.

Series 751 FireLock®European Alarm Check Valve Stations
17
Victaulic Companies
WORLD HEADQUARTERS
P.O. Box 31 • Easton, PA 18044-0031 Phone: 1-800-PICK-VIC (1-800-742-5842)
4901 Kesslersville Road • Easton, PA 18040 USA Phone: [phone] • Fax: [phone]
e-mail: [email protected]
VICTAULIC TOOL COMPANY VICTAULIC CONSTRUCTION PIPING SERVICES DIV.
P.O. Box 31 • Easton, PA 18044-0031 1818 Vultee Street • Allentown, PA 18103
Phone: [phone] • Fax: [phone] Phone: [phone] • Fax: [phone]
e-mail: [email protected] e-mail: [email protected]
Victaulic Around the World
VICTAULIC COMPANY OF AMERICA
P.O. Box 31 • Easton, PA 18044-0031
Phone: [phone] • Fax: [phone]
e-mail: [email protected]
VICTAULIC COMPANY OF CANADA VICTAULIC EUROPE
123 Newkirk Road • Richmond Hill, ON L4C 3G5 Prijkelstraat 36 • 9810 Nazareth, Belgium
Phone: [phone] • Fax: [phone] Phone: [phone] • Fax: [phone]
e-mail: [email protected] e-mail: [email protected]
VICTAULIC AMERICA LATINA VICTAULIC ASIA-PACIFIC
P.O. Box 31 • Easton, PA USA 18044-0031 541 Orchard Road • #14-02, Liat Towers
4901 Kesslersville Road • Easton, PA USA 18040 Singapore 238881
Phone: [phone] • Fax: [phone] Phone: [phone] • Fax: [phone]
e-mail: [email protected] e-mail: [email protected]
Victaulic Subsidiaries
AQUAMINE, LLC COASTLINE PLASTICS, LLC
247-A Vance Tank Road • Bristol, TN 37620 86334 Coastline Drive • Yulee, FL 32097- 3355
Phone: [phone] • Fax: [phone] Phone: [phone] • Fax: [phone]
VICTAULIC DEPEND-O-LOK, INC. GAMMA FOUNDRIES LTD.
P.O. Box 48776 • Atlanta, GA 30362 123 Newkirk Road • Richmond Hill, ON L4C 3G5
2681 Pleasantdale Road • Doraville, GA 30340 Phone: [phone] • Fax: [phone]
Phone: [phone] • Fax: [phone]
R
I-751.VDS 3580 Rev. C 3/04 ® Registered Trademark of Victaulic © Copyright 2004 Victaulic Printed in U.S.A. ZI00751VDS