Victorian Plumbing GATFCBB User manual

INSTALLATION INSTRUCTIONS
FOR NON LIGHTED CABINETS
Before installing this product pay special attention to these instructions. These products can
safely be fitted into Zone 2.
Cleaning Instructions
In order to maintain the quality finish of this product please do not use any abrasives or solvents
when cleaning this product. Use only a damp cloth for cleaning this product.
Do not allow water to stand on any part of the mirror.
Please clean any spillage that may aect the quality of the finish as described above.
Special Care
Care Should be exercised when cleaning this product. Although its finish is extremely durable, it
can be damaged by harsh abrasives and cleaning pads. To clean, use a light, non-abrasive
cleaning solution or cleaning polish.
V2.12.2022

Packing information & installation
Package content:
Cabinet
Screws
Manual
Technical page
Attention: Never modify the construction or add any parts which are not oered as
spare parts. Any unauthorized modification might result in weak mounting and risk
that mirror cabinet parts of the luminaire can fall down from the wall.
Note: Install the mirror at least 15cm. away from the basin.
Features
Adjustable Hinge (Select Models Only)
165° opening and closing range
If the cabinet door isn't flat, it can be adjusted using the screw (c) hidden
behind the removable cover on hinge.
WARNING: The distance between the door and the cabinet should not be
too small.Otherwise the door can't be opened and may lead to the door to
rupture.
Rotate CW: Distance between door and cabinet reduces. Rotate CCW:
Distance between door and cabinet increases.
Note:Some models can open less than 120 degree.Please open and close
door softly and avoid application of power to prevent rupture of door.
Adjustable Glass Shelving Panel
The height of the glass laminate can be adjusted up and down.
Step1: Unscrew and take out the glass shelves
Step2: Unscrew the glass shelf mounter and adjust height
Safety Warning:Do not disassemble the door unless necessary.
V2.12.2022
step2
step 1
c

Installation Steps
Hanging the Cabinet
Installation Procedure
Installation Tools
This product should be installed on a wall suitable to hold its weight. The installation must be
carried out by a professional and wrong installation may lead to product damage and personal
injury.
Measuring tape Spirit level Drill Hammer PencilScrewdriver
Fig.1 Fig.2
1. Fixing the bar
Open the product packaging, and check whether the product has any exception or functional
damage; if yes, please return it.
After selecting the location of the mirror cabinet, check whether the wall is solid, measure the
distance of the holes in the aluminum alloy bar with a tape measure and mark the wall with a
level and pencil (Fig. 1).
Drill holes in the marked position with electric drill and φ4 drill bit, and use special ceramic drill if
the wall surface is ceramic tile.
Knock the expansion plugs into the holes in the wall with a hammer,and then tighten the screws
with a screwdriver to fix the bar, and check the level with a spirit level (Fig. 2).
·
·
·
·
V2.12.2022

Hanging the Cabinet
2. Positioning and Installation of Mirror Cabinet
Fig. 3
Open
b1
b2 b2
Fig. 5Fig. 4
Attach the mirror cabinet to the bar as shown in Fig. 3, open the cabinet door, and mark on the
wall(b2) with a pencil through the backplate hole (b1).
Remove the mirror cabinet, drill the fixing hole in the wall in the marked position, and place the
expansion plugs (Fig. 4).
Repeat the operation as shown in Fig. 3 and mount the mirror cabinet to the bar, and then
tighten the screws on the backplate (Fig. 5).
Finally, check the mirror for level.
·
·
·
·
Recycling and disposal
Please recycle the packaging in accordance with your local government regulations on waste
handling, and follow the same advice at the end of the products life.
For more Information
Visit: victorianplumbing.co.uk
V2.12.2022