Victorian Plumbing MODE BATHROOMS BWRG80 User manual

Refer To Sheet 10 For Relevant Product Codes
Matt Black Framed 6mm
Wet Room Panel

1
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower . Some light surface marks are normal, and is a result of thescreen
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
2) Additional Notes
Please read these instructions carefully before starting installation.
Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION PART IMAGE DESCRIPTION
Drill
Flat-head
Screwdriver
Cross head
Screwdriver
Mallet
Silicone Sealant
PART IMAGE
PZ1

2
ASSEMBLY INSTRUCTIONS - DRAWING
NB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.
(9) 5x Wall Plugs
E
( )1 2x Top And Bottom Profiles
B
(10) 2x Cover Caps
E
(2) 2x Wedge Gasket Seals A
E
B(3) 1x Vertical Profile (11) 1x Support Bracket A D
E(4) 2x Wedge Gasket Seals B (12) 2x Screws 3.5*16
E
A(5) 1x Glass Panel (13) 1x Support Bracket B D
E(6) 5x Screws 4*30 (14) 1x Screw 4*12 D
E(8) 1x Gasket Hand Tool (16) 1x Wall Bracket D
B(7) 1x Wall Profile (15) 1x Top Bar D
PACK I.D PACK I.D
(2)
(11)
(16)
(5)
(14)
(3)
(12)
(1)
(6)
(7)
(4)
(13)
(8)
(9)
(10)
(15)

3
BOX CONTENTS
PACK I.D
D
D
D
D
E
D
E
E
E
A
E
B
B
E
E
B( )1 2x Top And Bottom Profiles
(2) 2x Wedge Gasket Seals A
(3) 1x Vertical Profile
(7) 1x Wall Profile B
(4) 2x Wedge Gasket Seals B
(5) 1x Glass Panel
(9) 5x Wall Plugs
(10) 2x Cover Caps
(6) 5x Screws 4*30
(11) 1x Support Bracket A
(12) 2x Screws 3.5*16
(13) 1x Support Bracket B
(14) 1x Screw 4*12
(16) 1x Wall Bracket
(15) 1x Top Bar
Component
(8) 1x Gasket Hand Tool
Picture

THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS
LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING
A 10mm TILE/WET WALL PANEL.
If you require help, we advise you to contact a competent plumber.
FITTED WET PANEL DRAWING
Installation Steps
ASSEMBLY INSTRUCTIONS
4
55
800/900
1000
100

5
STEP CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.1
834x21
1950x21
1950x21
1922x868x6
BWRG90
734x21
1950x21
1950x21
1922x768x6
BWRG80
Dimension in mm
Vertical Profile
Wall profile
Glass Panel
Top/Bottom horizontal profiles
Units supplied loose for self assembly
Measurement Matrix (before assembly)
STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION.
WALL
TILE OR WET
WALL PANEL
SHOWER TRAY
YES
WALL
TILE OR WET
WALL PANEL
SHOWER TRAY
NO
STEP 3 TRAY TO BE LEVEL
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THE
TRAY MEETS THE TILES / WET WALL PANELS.

6
4x4
2x4 6mm
3x4
ST4*30
5x4
1
STEP 4
WALL.
CONNECT BOTTOM PROFILE TO THE WALL PROFILE, DRILL WALL PROFILE TO THE
STEP 5 FIT THE GLASS PANEL.

7
STEP 6 FIT THE VERTICAL PROFILE AND TOP PROFILE.
STEP 7 FIT THE WEDGE GASKET SEALS.
1
2
3
x2
4Inside
x2
3
H2O
Inside
x2
1Inside
H2O
x2
2
Inside
Supplied
Hand Tool

STEP 8 FIT THE TOP SUPPORT BAR.
8
ST4*12
14
2.5mm
12
2.5mm
13
ST4*30
11
ST3.5*16
10
9
6mm
8
2.8mm
Take care not to
drill into the glass.
7
6
5
4
3
100mm
L
1
L-25mm
2

9
STEP 10 SILICONE THE OUTSIDE EDGES.
STEP 9 FITTING THE WALL PROFILE COVER CAPS.
Allow 24 hours for
silicone to dry before use.
Silicone on the outside edge only
x2

10
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
It is our intention that the quality and functions of this product
are of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
Product name: Matt Black Framed 6mm Wet Room Panel
Product code: BWRG80 BWRG90
Customer help line number:0344 804 48 48
2) MAINTENANCE
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier accepts
no liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
1) AFTER CARE INSTRUCTIONS
Regularly clean your shower product with warm soapy water
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.

V04/12/2019
The packaging you have received with your product is 100% recyclable.
It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
Victoria Plum Limited, Bridgehead Business
Hessle, HU13 0DG
Park
19
DOP No.:J191022001-2
Shower enclosures with aluminium
profiles and safety glass
Essential
characteristics
Performance Harmonised
technical
specification
Cleanability
Impact
resistance/shatter
properties
Pass
Pass
PassDurability
EN 14428:2015+A1:2018
Clause 4.2 of EN
14428:2015+A1:
2018
Clause 4.3 of EN
14428:2015+A1:
2018
Clause 4.4 of EN
14428:2015+A1:
2018