Viega Prevista Dry 8570.31 User manual

for support hinged handles, barrier-free pre-wall installation
Model Year built:
8570.31 from 10/2018
en_INT
Prevista Dry fixing element for 1120 mm
support hinged handles
Instructions for Use

Prevista Dry fixing element for 1120 mm support hinged handles 2 from 15

Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Intended use 6
2.1.1 Areas of use 6
2.2 Product description 6
2.2.1 Overview 6
3Handling 7
3.1 Assembly information 7
3.1.1 Installation dimensions 7
3.2 Assembly 7
3.2.1 Mounting to a masonry wall 7
3.2.2 Mounting in Prevista Dry Plus 10
3.2.3 Mounting in metal support profile 12
3.3 Disposal 15
Table of contents
Prevista Dry fixing element for 1120 mm support hinged handles 3 from 15

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista Dry fixing element for 1120 mm support hinged handles 4 from 15

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Dry fixing element for 1120 mm support hinged handles 5 from 15

2 Product information
2.1 Intended use
2.1.1 Areas of use
The Prevista Dry fixing element is used for fixing equipment in the bar‐
rier-free pre-wall installations. The construction height of the fixing ele‐
ment is 1120 mm.
The Prevista Dry fixing element is used for fixing supporting handles
onto the Prevista Dry WC elements.
2.2 Product description
2.2.1 Overview

Fig. 1: Component overview
1 Prevista Dry fixing element
2 Screws and dowels for fixing
Product information
Prevista Dry fixing element for 1120 mm support hinged handles 6 from 15

3 Handling
3.1 Assembly information
3.1.1 Installation dimensions




Fig. 2: Dimensions model 8570.31
3.2 Assembly
3.2.1 Mounting to a masonry wall
Determine and mark the fixing points.
nX2: 310 mm
Drill the holes.
Insert the dowels.
Mounting without WC element
煼
9
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 7 from 15

Determine and mark the fixing points on the floor.
nX3: 225 mm
Drill the holes.
Insert the dowels.
INFO! Mount the Prevista Dry fixing set pursuant to the instruc‐
tions for use for the fixing set.
Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
nX: 1000 mm
Tighten the feet of the element using a fork spanner (size 13).
ðThe element is attached to the wall.
9

9
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 8 from 15

The following steps describe mounting from the right-hand side of the
WC element. If required, repeat the same steps from the left-hand side.
Push the fixing element as far as it will go against the WC element.
Mount the wall fixing.
Set the height of the element by means of the feet.
nX: 1000 mm
Mounting at the WC element

Handling
Prevista Dry fixing element for 1120 mm support hinged handles 9 from 15

Use the fixing screw to connect the WC element and the fixing ele‐
ment.
Screw in the fixing screw and tighten it.
Repeat the mounting steps on the left-hand side.
3.2.2 Mounting in Prevista Dry Plus
Mount the Prevista Dry Plus pre-wall construction pursuant
to the instructions for use of the Prevista Dry Plus system.
Position the element on the floor rail.
Fix the feet on the floor rail using the clips.
Mounting without WC element


Handling
Prevista Dry fixing element for 1120 mm support hinged handles 10 from 15

Set the height of the element by means of the feet.
Fix the element with the Prevista Dry Plus Steptec rail connectors.
ðThe element is fixed in the Prevista Dry Plus pre-wall construc‐
tion.

Handling
Prevista Dry fixing element for 1120 mm support hinged handles 11 from 15

3.2.3 Mounting in metal support profile
Position the element on the floor rail.
If necessary, adjust the foot depth from 50 mm (pre-mounted) to 75
mm.
Pull the foot out and turn by 90°.
Screw the feet together with the support profile.
Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
nX: 1000 mm
Attach the element to the support profiles using the screws sup‐
plied.
Mounting with WC element

d

9

YY
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 12 from 15

If applicable, connect further elements to the element via the sup‐
port profile.
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 13 from 15

Position the element on the floor rail.
If necessary, adjust the foot depth from 50 mm (pre-mounted) to 75
mm.
Pull the foot out and turn by 90°.
Screw the feet together with the support profile.
Adjust the construction height of the element in accordance with the
on-site marking of the upper edge of the finished floor.
nX: 1000 mm
Attach the element to the support profiles using the screws sup‐
plied.
Mounting in metal support profile

d

9

YY
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 14 from 15

If applicable, connect further elements to the element via the sup‐
port profile.
3.3 Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Handling
Prevista Dry fixing element for 1120 mm support hinged handles 15 from 15