Viega Prevista Pure 8569 User manual

Instructions for Use
Prevista Pure bidet block
for wall-hung bidet, bricked in and surrounded
Model Year built:
8569 09/2018 - 09/2018
INT

Table of contents
1About these instructions for use 3
1.1 Target groups 3
1.2 Labelling of notes 3
1.3 About this translated version 4
2Product information 5
2.1 Standards and regulations 5
2.2 Intended use 5
2.2.1 Areas of use 5
2.3 Product description 5
2.3.1 Overview 5
2.3.2 Compatible components 6
3Handling 7
3.1 Assembly information 7
3.1.1 Mounting conditions 7
3.1.2 Installation dimensions 8
3.2 Assembly 9
3.2.1 Mounting the bidet block 9
3.2.2 Mounting the drain elbow 12
3.2.3 Setting up and cladding the bidet block 13
3.3 Disposal 15
Table of contents
Prevista Pure bidet block 2

1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nDrywall builder
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Prevista Pure bidet block 3

1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Pure bidet block 4

2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe and
are provided as a support feature.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger‐
many
Suitable masonry walls EN 1996-1-1
Suitable concreted walls DIN 1045
2.2 Intended use
2.2.1 Areas of use
The Prevista Pure bidet block is suitable for mounting on masonry wall
constructions pursuant to the regulations in section Ä „Regulations
from section: Fields of application / Mounting conditions“ on page 5.
2.3 Product description
2.3.1 Overview
The bidet block is equipped as follows:
Product information
Prevista Pure bidet block 5


Fig. 1: Components
1 Bidet pre-wall block
2 drain elbow
3 Flushing pipe connector
4 Protective plug
5 Holder for drain elbow
6 threaded rods for fixing sanitary objects
7 Fixing material for bidet ceramic
8 Plastic holder and metal bracket
9 Fixing material: dowels and screws
10 Mounting bracket for wall plates
11 Assembly accessories wall plates
2.3.2 Compatible components
The Prevista Pure bidet block is compatible with common WC ceramic
types. Fixing material for the bidet block and the ceramic is comprised
in the scope of delivery.
Product information
Prevista Pure bidet block 6

3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
nmasonry walls
nconcreted walls
nMetal support profiles
The wall constructions must comply with the regulations in section
Ä „Regulations from section: Fields of application / Mounting condi‐
tions“ on page 5.
The bidet block may only be mounted on even wall surfaces.
The bidet block can only be used in combination with wall-hung bidets
(fixing gauges for bore hole 180 mm or 230 mm).
Suitable walls
Bidet ceramic
Handling
Prevista Pure bidet block 7

3.1.2 Installation dimensions







Fig. 2: Dimensional drawing
Handling
Prevista Pure bidet block 8

3.2 Assembly
3.2.1 Mounting the bidet block
▶Break the locking clips off the wall mountings.
▶Select the wall mountings so that they match the distance from the
wall.
▶Push the wall mountings into the element.
▶Insert the locking clips.
ı
Handling
Prevista Pure bidet block 9

▶Screw the metal angles to the bidet block.
▶Adjust the construction height of the bidet block in accordance with
the on-site marking of the upper edge of the finished floor.
▶Mark the fixing points.
nX: 330 mm
▶Drill the holes.
▶Insert the dowels.
▶Tighten the bidet block via the mounting brackets using a fork
spanner (size 10).
9

煼

Handling
Prevista Pure bidet block 10