ViewZ VZ-AM03 User manual

VZ-AM03
Display 40”~55”

21
NOTE: Read the entire instruction manual before you start installation and assembly. Component Checklist
WARNING
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package W
ST6.3x55 (x6)
W-A
concrete anchor (x6)
W-B
D6 washer (x6)
W-C
adapter bracket (x2)
B
articulated arm assembly (x1)
A
Package M
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer
M-F
(x4)
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.

4
3
X X
√
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
1a. For Wood Stud Wall Mounting Fits for 406mm(16" ) stud
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
1b. For Solid Brick and Concrete Mounting
Screw the wall
mount onto
the wall
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
2.2"( )
55mm
(2.2")60mm
(2.4")
60mm
2.4"( )
60mm
(2.4")
ø 10mm
(ø 3/8")
Drill pilot holes
1
2
Mark the
exact location of
mounting holes
W-A
W-B
W-C
W-A
W-C
Screw the wall
mount onto
the wall
X X
√
12
Drill pilot holes
3
Find and mark the exact
location of mounting holes
XX

65
2-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the display.
· Screw the adapter brackets onto the display.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
2. Installing the Adapter Brackets
2-1 For Flat Back Screens
TV
TV
TV
Top of the display
M-A
M-B
M-C
M-F
or or or
M-C M-C
M-D
M-E
M-F
M-G
M-F
M-G
M-D
M-E
M-F
M-H
M-D
M-E
M-F
M-H
M-G
M-G
3. Hooking the Display onto the Wall Mount
wall