Viking SLP-1 Instructions for use

P
Pr ra ac ct ti ic ce e
T
TE EL LE EC CO OM MS SO OL LU UT TI IO ON NS SF FO OR RT TH HE E2 21 1S ST TC CE EN NT TU UR RY Y
TECHNICAL
TECHNICAL
SLP-1
SLP-1
Single Line
Paging Controller
June 8, 2012
Add Paging to Your Existing Phone Line
Without an Expensive Phone System
The SLP-1 Single Line Paging controller will allow
you to page family members or co-workers from
any phone in your home or small office. The pages
can be heard over the same speakers that are
installed for multi-zone music distribution.
The SLP-1 connects in series with a single existing
phone line. The unit has a built-in 2 watt amplifier,
pre-amp output, music on hold input, intercom fea-
tures and selectable loud ringing. The SLP-1 pro-
vides an input for a lighted doorbell switch, allowing
a door chime to be heard over existing speakers. Page from several different phone
lines by connecting multiple units.
P
Ph ho on ne e. .. .. .7 71 15 5. .3 38 86 6. .8 88 86 61 1
Power: 120V AC/13.8V AC 1.25A, UL listed adapter provided
Dimensions: 133mm x 89mm x 44mm (5.25” x 3.5” x 1.75”)
Shipping Weight: 1.36 kg (3 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
Paging Amplifier Output: 2 watts - powers up to (3) 8 ohm or
(16) 45 ohm speakers
Sound Pressure: 100 dB @ 1 meter (loud electronic warble from
25AE paging horn)
REN: 0.5A
Max Speaker Output Wire Run: 91m (300 ft) max, 18 AWG
Max Doorbell Switch Wire Run: 305m (1000 ft) max, 24 AWG
Max Load on Page Trigger Output: 1K Ohm
Talk Battery: 36V DC
Connections: (1) 6-position and (1) 8-position screw terminal
blocks, (1) 3.5mm (1/8”) jack, (4) RCA jacks, 2.13m (7 ft) audio
cord with 3.5mm (1/8”) double ended mono plugs included
S
Sp pe ec ci if fi ic ca at ti io on ns s
F
Fe ea at tu ur re es s
• Whole house/small business paging from existing phones
• Built-in two-watt mono paging amplifier with gain control
• Phone to phone intercom
• Page from several different phone lines by connecting
multiple units
• Music on hold
• Caller on hold
• Can provide background music from an external source
• Background music mute (automatic during paging or
touch tone selectable while you are on a call)
• Selectable loud ringing (electronic warble over speakers)
• Doorbell switch input (lighted or non-lighted) for activating
door chime (ding-dong sound over speakers)
• Unique front and back door chimes when used with a
C-1000B or C-2000B doorbox controllers
• Switch selectable On-Hold alarm tones
• Stereo pre-amp input and line level output for use with
receivers and high wattage amplifiers
• Simple control commands - no touch tone programming
• Page trigger output (12V signal for enabling paging
source input on multi-source amps)
• Pre-amp volume control
• Bypass code - ignores all touch tones on next off-hook
allowing you to steer through auto attendants, etc.
• Comes complete with power supply
h
ht tt tp p: :/ // /w ww ww w. .v vi ik ki in ng ge el le ec ct tr ro on ni ic cs s. .c co om m
i
in nf fo o@ @v vi ik ki in ng ge el le ec ct tr ro on
ni ic cs s. .c co om m• Whole house paging from an existing phone
line
• Add paging, intercom, and music on hold
features for small businesses
• Loud ringing / night bell
• Provide unique front and back door chimes
when used with a C-1000B or C-2000B
A
Ap pp pl li ic ca at ti io on ns s

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]
Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The
customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)
number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual-
ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
F
Fe ea at tu ur re es sO Ov ve er rv vi ie ew w
DIP Switches - For on-hold alarm
and mode selections. (see page 6)
ON
OFF
1 2 3
ON
C.O. / Phone Line Input
Line Out to Phones
Speaker Output (2 watt maximum,
connect up to three 8-ohm speakers in parallel)
Pre-Amplifier Volume Control - For paging,
loud ringing, door chime and on-hold alarm tones.
- +
Doorbell Switch Input (lighted or non-lighted) -
Provides door chime over speakers (not polarity
sensitive). This input can also be connected to a
Viking model C-1000B or C-2000B for unique
front / back door chimes.
Loud Ring Enable Input (shorted: enabled,
open: disabled) Provides warble over
speakers during phone line ringing.
I.O. Communications - Connect to multiple
units for multi-line applications with one
amplifier (polarity sensitive).
Page Trigger Output - Connect to multi-zone
amplifiers requiring a switched 12VDC signal
(or dry relay contact closure) for enabling the
paging source input.
Left and Right Audio Loop Input (stereo,
RCA-type) Line level pre-amp input for
background music, etc.
Music on Hold Input (mono, 1/8" / 3.5mm)
Line level input from radio, etc.
Left and Right Audio Loop Output (stereo,
RCA-type) Line level output to external amplifier.
Power Indicator LED
Page Active LED
Mute Status LED
J10 Page Trigger Contact
Closure Remove both jumpers and
reconnect one jumper across pins
2 & 3 to change "Page Trigger
Output" to a N.O. relay contact.
J9 Optional Page Trigger (Dry)
Secondary relay output contacts
for controlling existing door chimes,
etc. (solder pads only, available on
top or bottom side of PCB).
DOO
R BELL
S
W. INPUT
L
OU
D RIN
G
ENAB
L
E
-
+
I.
O
.
CO
M
.
ON
1 2
3
PWR
P
AG
E
MUTE
M
PA
G
E TRI
G
.
OUT
C.O. LIN
E
I
NP
UT
O
UT T
O
PH
O
NE
S
-
SPKR
+
OU
TP
U
T
L
L
R
R
- +
V
IKIN
G
©
V
IKIN
G
E
LECTR
O
NIC
S
H
UDSON,
WI
54
016
SINGLE LIN
E
P
A
G
IN
G
C
O
NTR
O
LLE
R
PO
WER 1
3
.
8
VA
C
M
O
DEL
S
LP-
1
PREAMP
VO
L
U
M
E
2
WA
TT
A
A
AMP
GAI
N
MIN
MIN
MAX
MAX
MIN
MIN
MAX
MAX
M
US
I
C
ON
HOLD
INP
U
T
A
UDIO
INP
U
T
L
R
AU
DI
O
OU
TP
U
T
L
R
Internal 2 Watt (Mono) Amplifier Gain
Control - To adjust speaker output volume.
2
If trouble is experienced with the SLP-1, for repair or warranty information, please contact:
Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 [phone]
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com-
mission or corporation commission for information.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:
Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.
It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.
PART 15 LIMITATIONS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
FCC REQUIREMENTS
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this
equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If
requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as deter-
mined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this SLP-1 does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
If the SLP-1 causes harm to the telephone network, the telephone company will notify you in advance that temporary dis-
continuance of service may be required. But if advance notice isn't practical, the telephone company will notify the cus-
tomer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec-
essary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
the necessary modifications to maintain uninterrupted service.
LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu-
factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover
non-EWP products that have been exposed to wet or corrosive environments.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-
NESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM-
AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL
BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU-
SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.

I
In ns st ta al ll la at ti io on na an nd dA Ap pp pl li ic ca at ti io on ns s
25AE Paging
Horn (not included)
Music On Hold
Source (Radio)
13.8V AC
Adapter
(included)
120V AC
C.O. / Phone
Line
Standard
Analog Phone
To Additional Standard
Analog Phones
1/8" (3.5mm) Double Ended
Audio Cord (included)
- or -
Optional
30AE Ceiling
Speaker (not included)
Up to (3) 8-Ohm Paging Horns
or Ceiling Speakers may be connected
Doorbell Switch (lighted or
non-lighted) SPST with 6-16V bulb
Pre-Out or
* Tape Out
Main In or
* Tape In
L R
Stereo Receiver
* Note: Tape monitor loop
(switch) on the stereo receiver
must be enabled (ON).
L R
"Night"
Switch (SPST)
ShortedTime Controlled
Relay
- or -- or -
Optional Methods for
Enabling Loud Ringing
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
See DIP Switch
Programming (page 6)
3
A. Installation Using the Internal 2-Watt Amplifier, Stereo Receiver, Doorbell Input, Music On
Hold and Providing Optional Loud Ringing
B. Connecting to a Separate Pre-Amp and Power Amp
Music On Hold
Source (Radio)
13.8V AC
Adapter
(included)
120V AC
C.O. / Phone Line
Standard
Analog Phone
To Additional Standard
Analog Phones 1/8" (3.5mm) Double Ended
Audio Cord (included)
-
+
Main Out Input
L R L R
Pre-
Amplifier
(Background
Music Source)
Power
Amplifier
Up to (3) 8 Ohm Speakers
or Paging Horns (optional)
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
See DIP Switch
Programming (page 6)
For more information on the 25AE
and 30AE, see DOD# 498.

DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
C.O. / Phone Line
Standard
Analog Phone
To Additional Standard
Analog Phones
+
-
Page Input
** Multi-Zone
Controller/Amplifier
Page Trigger
(Control) Input
+
-
*Optional 12VDC or
relay contact page
trigger output
(20mA maximum)
- +
Optional Page Trigger "Dry"
Secondary Relay Output Contacts
(1A @ 30VDC maximum)
Note: Connections to J9 require
soldering to back side of PCB.
3 2 1
N.O. COM N.C.
J9
Doorbell
Switch
Up to (3) 8 Ohm Speakers
or Paging Horns (optional)
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
13.8V AC
Adapter
(included)
120V AC
* Note: Most multi-zone controllers/amplifiers require a 12VDC trigger signal or relay contact closure to automatically switch the source to the “page” input. The
SLP-1 will provide a switched 12VDC (20mA maximum) signal or relay contact closure which is maintained while the unit is paging or for the duration of the
chime/ding-dong sound (approximately 2 seconds). The SLP-1 can also provide a secondary “dry” contact page trigger output. N.O. and N.C. relay contacts are
available on solder pads J9 1-3 (see diagram above). Users often turn off all zones when they retire for the evening. In this event, we recommend dedicating
up to three 8-ohm speakers on the SLP-1’s 2 watt speaker output. They should be placed in central locations (hallways, etc.) on each level so the door chime
can be heard when all zones are disabled. Caution: This connection is polarity sensitive.
D. Multi-Line Paging with a Single Amplifier
Line 1
(C.O. / Phone Line)
Standard
Analog Phone
To Additional
Standard Analog
Phones
Main Out
L R
Pre-Amplifier
(Background
Music Source)
+
-
Input
L R
Power
Amplifier
To Additional
SLP-1 Units
(Up to 10 total)
Line 2
(C.O. / Phone
Line)
Standard
Analog Phone
To Additional Standard
Analog Phones
To Additional
SLP-1 Units
(Up to 10 total)
- +
-or-
*Up to (3)
Optional
Speakers
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
- +
13.8V AC
Adapter
(included)
120V AC
Caution: I.O. communications
connection is polarity sensitive.
4
* Note: The internal 2 watt amplifier
should only be used on the last
SLP-1 in the chain.
C. Connecting to the “Page” Input on Multi-Zone Controllers / Amplifiers and Controlling an
Existing Doorchime
Note: The background music mute command (#5), should not be used when connecting multiple SLP-1’s to a single amplifier,
see Operation section K, page 7.
** Warning: Multi-zone controllers without a page trigger input
(audio sensing only) are not recommended, as the 1st word dur-
ing paging is usually omitted.

F. Provide Paging, Doorbox, and Doorstrike Control with Unique Front and Back Door Chimes
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
DOOR ENTRY / CCTV VIDEO
CONTROLLER
POWER 13.8V AC
MODEL C-1000B
PHONE LINE
INPUT
EARTH
GND
21 3 4 5 14 15 16
LINE OUT
TO PHONES
67
KEYLESS CONTACT
CLOSURE INPUT
DOORBOX 1
DOORBOX 2
891011
DOORBOX
PWR OUTPUT
12 13
DOOR STRIKE 1
N.O.
COM
N.C.
17 18 19
DOOR STRIKE 2
N.O.
COM
N.C.
C.O. / Phone Line
EARTH
GND
C.O. LINE
INPUT
OUT TO
PHONES
KEYLESS
C.C. INPUT
DOOR
BOX 1
DOORBOX
13VAC PWR
DOOR
BOX 2
N.O. COM N.C.
DOOR STRIKE 1
SIG GND
VIDEO 1 IN
SIG GND
VIDEO 2 IN
SIG GND
VIDEO OUT
N.O. COM N.C.
DOOR STRIKE 2
TALK BATTERY
OFF ON
C
LED1
C
LED2
C
LED3
ON
1 2 3
COM N.O. N.C. - - - - AUX.
CONTACT
OUTPUT
Standard
Analog Phone
To Doorstrike/
Magnetic Lock 2
To Doorstrike/
Magnetic Lock 1
To Additional
Standard
Analog Phones To Viking Doorbox 1
(Front Door)
To Viking Doorbox 2
(Back Door)
DIP Switch 2
must be ON
ON
OFF
1 2 3
ON
Up to (3) 8 Ohm
Speakers or Paging
Horns (optional)
Page Input
Multi-Zone
Controller/Amplifier
Page Trigger
(Control) Input
+
-
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
*Optional 12VDC
page trigger output
(20mA maximum)
- +
13.8V AC
Adapter
(included)
120V AC
13.8V AC
Adapter
(included)
120V AC
5
Note: To provide unique front and back door chimes, the C-1000B must be programmed to enable the “Auxiliary Contact Mode” ( Q 7) and have the auxiliary con-
tact programmed for custom ring cadence (12#03). Doorbox ringing can also be disabled by placing the C-1000B in the “Doorbell Mode” (
Q 1). See the C-1000B
Technical Practice for programming details. The C-1000B CCTV Video Control Mode can NOT be used in conjunction with unique front and back door chimes.
See Operation section I, page 7. If CCTV video control is required, a Viking VC-1000 can be used. The caller’s music on hold is limited to 5 seconds while com-
municating with a doorbox.
* Note: Page trigger output can be changed to a
contact closure, see “Note” in section Eabove.
E. Provide Paging, Music-On-Hold and Single Entry Phone Control
C.O. / Phone
Line Input
Analog
Phone
* Earth Ground
(optional)
Optional wiring for
door chime over
speakers. If used,
set the C-200 DIP
switch 2 to OFF.
E-40-PB
Door Entry
Phone
(not included)
To Additional
Analog Phones
Page
Input
Multi-Zone
Controller/Amplifier
Page Trigger
(Control) Input
+
-
- +
DIP Switch 2
must be ON
ON
OFF
1 2 3
ON
Music On Hold
Source (Radio)
1/8" (3.5mm) Double Ended
Audio Cord (included)
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
*Optional 12VDC
page trigger
output (20mA
maximum)
EARTH
GND
C.O. LINE
INPUT
OUT TO
PHONES
ENTRY
PHONE
N.O. COM N.C.
AUX CONTACTS
ON
1 2 3
AUX POWER
OUTPUT
VIKING
POWER 13.8V AC
©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE ENTRY PHONE
CONTROLLER
MODEL C-200
RING COUNT
1
EARTH GND
1
RELAY MODE
2
DOORBELL MODE
3
IN USE LINE IN
23
PHONES
45
ENTRY
6789
AUX POWER
OUTPUT
10 11 12
AUXILIARY RELAY
N.O.
COM
N.C.
13.8V AC
Adapter
included
120V AC
* Note: Most multi-zone controllers/amplifiers require a 12VDC trigger signal or relay contact closure to automatically switch the source to the “page” input. The
SLP-1 will provide a switched 12VDC (20mA maximum) signal or relay contact closure which is maintained while the unit is paging or for the duration of the
chime/ding-dong sound (approximately 2 seconds). The SLP-1 can also provide a secondary “dry” contact page trigger output. N.O. and N.C. relay contacts are
available on solder pads J9 1-3 (see diagram above). Users often turn off all zones when they retire for the evening. In this event, we recommend dedicating
up to three 8-ohm speakers on the SLP-1’s 2 watt speaker output. They should be placed in central locations (hallways, etc.) on each level so the door chime
can be heard when all zones are disabled. Caution: This connection is polarity sensitive.
For more information on the C-1000B,
see DOD# 168.
For more information on Doorboxes,
see DOD# 170.

LED3
LED1 LED2 LED4 LED5 LED6 LED7 C
CCCC
C C
J11-
123
J10-
123
J9-
123
J8-
123
J7-
123
123
on
4 5
VIKING©MODEL C-2000B
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7 89 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PWR 13.8 VAC
EARTH GND ENTRY PHONE 1 DOOR STRIKE 1 ENTRY PHONE 2 DOOR STRIKE 2 ENTRY PHONE 3 DOOR STRIKE 3 ENTRY PHONE 4 DOOR STRIKE 4 DOORBELL SWITCH / AUX. INPUT AUX. CONTACT OUTPUT PHONE LINE INPUT LINE OUT TO PHONES
ANALOG STATION INPUT
C.O. /
Phone Line
Music On Hold
Source (Radio)
1/8" (3mm) Double Ended
Audio Cord (included)
To Optional Speakers
or Paging Horns
To "Page" input
on your whole house
audio controller
Standard
Analog
Phone
To Additional Standard
Analog Phones
To Standard Analog Phones
or Viking Entry Phones
models: E-10A, E-20B, E-30,
E-40, E-50, E-60,K-1500-7,
K-1700-3 or K-1900-8.
To Doorstrike/Magnetic Lock
13.8V AC
Adapter
(included)
120V AC
ON
OFF 1 2 3
ON
DIP switch 2 must
be ON (see below)
*DIP Switch 1
must be OFF
OFF ON
123
on
4 5
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
13.8V AC
Adapter
(included)
120V AC
D
DI IP PS Sw wi it tc ch hP Pr ro og gr ra am mm mi in ng g
DIP Switches
(shown in factory
default positions)
ON
OFF 1 2 3
ON
DOOR BELL
SW. INPUT
LOUD RING
ENABLE
- +
I.O. COM.
ON
1 2 3
PWR PAGE MUTE
PAGE TRIG. OUT
C.O. LINE
INPUT
OUT TO
PHONES
- SPKR +
OUTPUT
LLRR
- +
VIKING©
VIKING
ELECTRONICS
HUDSON, WI 54016
SINGLE LINE
PAGING CONTROLLER
POWER 13.8 VAC
MODEL SLP-1
PREAMP
VOLUME
2 WATT
AMP GAIN
MIN MAX MIN MAX
MUSIC
ON
HOLD
INPUT
AUDIO
INPUT
L R
AUDIO
OUTPUT
L R
O
Op pe er ra at ti io on n
A. Paging
To page throughout the house/small business, simply press #, then 7(the letter “P” key on your keypad). Speak into the phone
receiver and your voice will be heard throughout the house or small business over the speakers. If background music is present over
the speakers, it will automatically mute allowing your page to be heard. If you have a caller on the phone, they will automatically be
put on hold. You can get the caller back by simply pressing #8 or by momentarily hanging up. Note: The PAGE LED will light dur-
ing paging.
6
Note: Place DIP switches in the desired position then momentarily power down the unit.
* Note: This mode will provide separate chimes for doorbox 1 and 2 when used with a C-1000B or C-2000B (see Operation section I).
G. Provide Paging with Unique Front and Back Door Chimes and Control of Up to Four
Entry Phones and Doorstrikes from a Single Phone Line
Switch
1
1
2
2
3
3
Position
OFF
ON
OFF
ON
OFF
ON
Description
On-hold alarm disabled
On-hold alarm tone enabled, a double beep
each minute a call is on hold (factory default)
Doorbell input connected to a typical doorbell
switch (factory default)
* Doorbell input connected to a C-200, C-1000B
or C-2000B N.O. auxiliary contact output
Instant outside line access (factory default)
Dial “9” to access an outside line
H. Eliminating Paging Feedback Squeal
Paging feedback squeal can occur when phones are used in close proximity to the paging speakers. To eliminate paging feedback,
turn down the paging volume, move the phones away from the speakers or install a Viking model FBI-1A Digital Anti-Feedback
Paging Interface. For more information on installing the FBI-1A with the SLP-1, see DOD# 465.
Note: To provide unique front and back door chimes, the C-2000B must have the “Auxiliary Contact Mode” enabled (DIP switch 1
OFF) and have the auxiliary contact programmed for “Entry Phone Triggered Ring Cadence Activation” (3#60). Entry phone ringing
can also be disabled (0#62). See the C-2000B Technical Practice for programming details.The caller’s music on hold is limited to 5
seconds while communicating with an entry phone. If CCTV video control is required, up to 2 Viking model VC-1000’s can be used.
* Important: See the C-2000B
Technical Practice for complete pro-
gramming instructions (DOD# 156).
Important: With a C-2000B as the controller, the rev level of the SLP-1 must be REV F or higher in order for this applica-
tion to work. If the controller is a C-2000A, the rev level of the SLP-1 must be no higher than REV E.

B. Placing a Call On Hold
To place a call on hold, simply press #then 6(the letter “O” key on your keypad), two beeps should be heard confirming the call is
on hold, then hang up. The call can then be taken on another phone elsewhere in your home or small business. Optional Music-On-
Hold can be provided.
C. Releasing a Call On Hold
If you hang up the phone after placing a call on hold, simply coming off-hook with any phone will return you to the caller on hold. If
you have placed a caller on hold (#6) or have announced a page (#7) and have remained off-hook, enter #8 or momentarily hang
up to return to the caller on hold.
If the caller hangs up while on hold, the SLP-1 can sense a CPC disconnect signal and will automaitcally release the line. Note:
The SLP-1 has a maximum on-hold call time of 1 hour. After a caller has been on hold for 1 hour, the SLP-1 will automatically dis-
connect the call.
D. On-Hold Alarm Tones
The SLP-1 can provide on-hold alarm tones to alert you that a caller has been left on hold. After each minute the call has been left
on hold, the SLP-1 will momentarily mute the background music and output a double beep tone over the speakers. This feature can
be disabled by setting DIP switch 1to OFF (see DIP Switch Programming page 6).
E. Phone to Phone Intercom
This feature allows you to first page someone over the speakers, then speak with them over the phone without the conversation
being heard over the speakers. To perform this function, simply press #, then 7(the “P” key on your keypad), announce your page,
then press the numeric 0key. Another phone coming off-hook will be instantly connected.
F. System Bypass
The system bypass allows you to use outside phone services (automated attendants, etc.) that require the use of the #key. Come
off hook with any phone and enter #9, two confirmation beeps should be heard, hang up the phone. The SLP-1 will now ignore all
Touch Tone commands on the next off-hook.
G. Music Mute
To mute the background music any time you are on the phone, simply enter #5. The background music will return when you enter
#5 again or hang-up the phone. The MUTE LED will light while the background music is muted. Note: The music mute command
(#5) should not be used in multi-line applications.
H. Outside Line Access Mode
With DIP switch 3in the OFF position (see DIP Switch Programming page 6), simply coming off-hook will instantly give you the
outside line. With DIP switch 3in the ON position, you must dial a “9” to get an outside line. The SLP-1’s features remain the same
in either mode. Note: Instant outside line access mode is for use with private dial tone.
I. Door Chime (Doorbell Switch Input)
With DIP switch 2in the OFF position (see DIP Switch Programming, page 6), the doorbell input terminals on the SLP-1 can be
connected to a normally open switch (lighted or non-lighted doorbell buttons, etc.). When the switch is activated, the unit will
momentarily mute the background music and provide a door chime (ding-dong) sound over the speakers. Note: This input is not
polarity sensitive and is designed to light standard 6-16V lighted doorbell switches.
With DIP switch 2in the ON position, the doorbell input terminals on the SLP-1 can be connected to the C-1000B or C-2000B nor-
mally open auxiliary relay contacts. When doorbox 1 on the C-1000B is activated, the SLP-1 will momentarily mute the background
music and provide a door chime (ding-dong) sound over the speakers. When doorbox 2 on the C-1000B is activated, a single chime
(ding) will be heard over the speakers. When doorphone 1 on the C-2000B is activated, the SLP-1 will momentarily mute the back-
ground music and provide a door chime (ding-dong) sound over the speakers. When door phone 2, 3 or 4 on the C-2000B is acti-
vated, the SLP-1 will produce 2, 3 or 4 dings respectively. This is ideal for determining which door the visitor is located at without
having to answer the telephone. Note: The C-1000B or C-2000B must have the auxiliary contact mode programmed for custom
ring cadence. For more information, refer to the C-1000B or C-2000B Technical Practice.
J. Loud Ringing
The SLP-1 can momentarily mute background music and provide loud ringing (warble sound) over the speakers each time the
incoming phone line rings. To enable this feature, short terminals labeled LOUD RING ENABLE. This input can also be connected
to a SPST switch or time controlled relay for night ring applications. Note: With loud ringing enabled, if the incoming phone line
rings during a page or phone to phone intercom, a short “loud ring” burst will be heard over the speakers every 15 seconds or until
the line stops ringing.
K. I.O. Communications (for Multi-Line Applications)
The SLP-1 is designed to operate on a single phone line. If paging is required on two or more phone lines, connect one SLP-1 per
line. Multiple SLP-1’s can be connected to the same Pre-Amp, Amp or Receiver. In this application the terminals labeled IO COM
should be connected in parallel to each SLP-1. Caution: This connection is polarity sensitive. With the I.O. communication con-
nected between each SLP-1, paging will be allowed on a first come, first serve basis. If paging is active on one SLP-1, any person
attempting to page on another SLP-1 will hear a busy signal on their phone. 7

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 478 Printed in the U.S.A.
P
Pr ro od du uc ct tS Su up pp po or rt tL Li in ne e. .. .. .7 71 15 5. .3 38 86 6. .8 86 66 66 6F Fa ax xB Ba ac ck kL Li in ne e. .. .. .7 71 15 5.
.3 38 86 6. .4 43 34 45 5
ZF302030 Rev C
Quick Reference Guide
“P” for Page. Speak into the phone
receiver and your voice will be heard
throughout the house or small busi-
ness over the speakers. Pressing #7
automatically places a caller on hold;
to return to the caller after the page
press #8 or momentarily hang-up.
“O” for On-Hold. Allows you to place a
caller on hold (with music), hang up
and take the call on another phone in
the house or small business.
This releases the caller on hold, allow-
ing you to converse with the caller.
This allows you to talk with someone
at another phone in the house or small
business after a page, without the
conversation being heard over the
speakers.
Enter #9, hear two beeps, and hang-
up. The SLP-1 will now ignore all com-
mands on the next off-hook. This
allows you to use outside phone serv-
ices (automated attendants, etc.) that
require use of the # key.
This command allows you to mute the
background music coming through
your speakers for the duration of an
incoming or outgoing call.
Enter 9to gain access to outside dial
tone. Note: With DIP switch 3in the
OFF position, you will instantly have
outside line dial tone from off-hook (for
use with private dial tone).
Feature: Touch Tone
Command: Description:
Standard Features
Door Chime: Background music will mute and a door chime
(ding-dong) sound will be heard over the speakers.
Loud Ringing: When enabled, background music will mute and
incoming call ringing (warble) sound will be heard over the
speakers for the duration of the ring.
On-Hold Alarm Tones: Each minute the call has been placed
on hold, the background music will mute and a double On-Hold
alarm tone will be heard over the speakers. Note: This feature
can be disabled by setting DIP switch 1to OFF.
VIKING Model SLP-1
Q
Qu ui ic ck kR Re ef fe er re en nc ce eG Gu ui id de es s
Note: Make a photocopy of the Quick Reference Guides (below) and place one near your phones for quick
reference to all of the SLP-1 Touch Tone commands.
8
Page # 7
Hold # 6
Release
Hold
# 8 or momen-
tarily hang-up
Phone-To-
Phone
Intercom
# 7 then 0
System
Bypass
# 9, then
momentarily
hang up
Music
Mute # 5
Outside
Line
Access
(use only with
DIP switch 3 ON)
9
Quick Reference Guide
“P” for Page. Speak into the phone
receiver and your voice will be heard
throughout the house or small busi-
ness over the speakers. Pressing #7
automatically places a caller on hold;
to return to the caller after the page
press #8 or momentarily hang-up.
“O” for On-Hold. Allows you to place a
caller on hold (with music), hang up
and take the call on another phone in
the house or small business.
This releases the caller on hold, allow-
ing you to converse with the caller.
This allows you to talk with someone
at another phone in the house or small
business after a page, without the
conversation being heard over the
speakers.
Enter #9, hear two beeps, and hang-
up. The SLP-1 will now ignore all com-
mands on the next off-hook. This
allows you to use outside phone serv-
ices (automated attendants, etc.) that
require use of the # key.
This command allows you to mute the
background music coming through
your speakers for the duration of an
incoming or outgoing call.
Enter 9to gain access to outside dial
tone. Note: With DIP switch 3in the
OFF position, you will instantly have
outside line dial tone from off-hook (for
use with private dial tone).
Feature: Touch Tone
Command: Description:
Standard Features
Door Chime: Background music will mute and a door chime
(ding-dong) sound will be heard over the speakers.
Loud Ringing: When enabled, background music will mute and
incoming call ringing (warble) sound will be heard over the
speakers for the duration of the ring.
On-Hold Alarm Tones: Each minute the call has been placed
on hold, the background music will mute and a double On-Hold
alarm tone will be heard over the speakers. Note: This feature
can be disabled by setting DIP switch 1to OFF.
VIKING Model SLP-1
Page # 7
Hold # 6
Release
Hold
# 8 or momen-
tarily hang-up
Phone-To-
Phone
Intercom
# 7 then 0
System
Bypass
# 9, then
momentarily
hang up
Music
Mute # 5
Outside
Line
Access
(use only with
DIP switch 3 ON)
9
Note: Touch Tone commands are ignored during doorchimes, loud ringing and on-hold alarm tones.