Vip-Vision SLR-A75-4G User manual

SLR-A45 Series
Solar Surveillance Installation Guide
Version 130618
Thank you for purchasing a SLR-A45 Series Solar Surveillance System.
This install guide covers basic setup, installation and use of your surveillance system.
For more information, please visit:
www.vip-vision.com
WiFi Solar Surveillance System (SLR-A75-4W)
4G Solar Surveillance System (SLR-A75-4G)

2
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
1. Pre-install Information
#Part Product Code Image
1x Solar Panel
(Optional config remote) SSL-A40MN
1x 4.0MP Mini PTZ Dome Camera VSIP4MPPTZMINI
1x Camera Adapter VSBKTA107
1x Wall Mount Adapter VSBKTA110
1x Right Angle Bracket VSBKTB300S
1x Junction Box VSBKTA140
1x Pole Mount Bracket VSBKTA150
1x 128GB microSD card MICROSD128GB
2x
Ubiquiti 5.8GHz 120° Wireless Bridge
(1x Access Point, 1x Station)
(WiFi system only) WT5-ULB
1x Huawei 4G Modem Router with WiFi
(4G system only) VSWAN4GHW
1.1 Included components
Pole, base plate & SIM card not included.
Required Install Tools: Allen key for junction box (included), 8mm drill bit & battery
drill, flat head screwdriver. Laptop with RJ45 network interface strongly recommended
for camera setup.

3
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
Motion Sensing Solar Panel with 40W Street Light
Panel Type 75W monocrystalline silicon panel
Battery 41.6Ah Lithium Iron Phosphate (LiFiPo 4) with Low Voltage Cutoff
Panel Tilt Adjust -60° ~ 60°
Ingress Protection (Panel) IP66
Wind Tolerance Up to 65m/s
Dimensions (Panel) 1063 x 259 x 526mm
Pole Diameter (Spigot) Ø60mm
Note: This solar panel system is fitted with undervoltage protection, which disconnects
the load at approximately 10.8V. If you are not receiving any voltage on the output wires,
place the panel in direct sunlight for a minimum of one hour and re-test. The output will be
reconnected automatically when battery voltage reaches approximately 11.5V.
This solar panel includes a motion-activated LED light which is disabled by default. For
more information, refer to 4. Solar Panel LED Configuration (p16).
LED light configuration requires the solar panel remote control (provided on request).
1.2 Solar Panel Information

4
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
526mm 1063mm
259mm
M8*30 x 4
M6 O x 4
M6
M6*15
M8 x 4
M6 O x 2
M
M6*16 x 2
M8
M8
M8*2
6 C x 2
O x 2
C x 2
0 x 2
x 4
C x 4
M8*3
M
Φ50-60mm
8 x 4
0 x 4
Solar Panel Dimensions
Solar Panel Screw Diagram

5
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
Professional Series 4.0MP 4x Zoom Mini PTZ Dome
Note: Camera has been preinstalled with the supplied 128GB microSD card and has been
preconfigured to record 4.0MP (2592 x 1520) at 25fps.
The username and password details have been preset to:
username: admin
password: admin123
To prevent unauthorised access, ensure you change the admin password before completing
installation.
Default Camera Configuration
Main Stream
Stream Type General
Encode Type H.265
Resolution 2592x1520
FPS 25
StreamCTRL VBR
Quality 6 (Best)
Ref Stream 1536-8192Kbps
I Frame Interval 50
Watermark Yes
Characters DigitalCCTV
Sub Stream
Stream Type General
Encode Type H.265
Resolution 704x576 (D1)
FPS 10
StreamCTRL CBR
Bit Stream 512Kbps
Ref Stream 139-768Kbps
I Interval 20
SVC 1 (off)
Solar Panel Dimensions
Solar Panel Screw Diagram
1.3 Camera Information

6
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
2.1 Mounting the solar panel to the pole
1. Drill an 8mm hole in the pole (minimum 15cm down from the top of the pole) on the same side
that the camera will be mounted. This is for the solar panel cable to run through. The position
of the hole will vary depending on what position on the pole the camera is to be mounted.
2. Feed the figure 8 cable connected to your solar panel through that hole
3. Place the solar panel bracket on top of the pole.
4. Securely fasten the included grub screws to the bracket. Tighten the locking bolts to prevent
the grub screws from loosening. (Fig. 2.1b)
2. Installation
8mm
Fig. 2.1a
Solar panel power cable drill location
Fig. 2.1b
Installed grub screws

7
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
2.2 Adjusting solar panel angle
1. Use a flat head screwdriver to remove the bracket cover (Fig. 2.2a).
2. Once the cover is removed, loosen the Allen head to adjust the solar panel angle (Fig. 2.2b).
To ensure your solar panel absorbs as much light as possible, it’s important to adjust the solar panel
angle to an ideal angle, depending on your region (refer to table below).
3. Tighten the bolt after adjusting the angle to secure the solar panel in place.
4. Replace the cover.
Ideal panel angles (H°) by Australian city
Sydney Melbourne Perth Brisbane Hobart Adelaide Darwin
34° 38° 32° 27.5° 43° 35° 12.5°
Fig. 2.2a
Solar panel angle adjust cover
Fig. 2.2b
Solar panel angle adjust Allen head

8
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
A
B
C
D
E
F
46-70mm
Band Clamps
G
2.3 Mounting the camera to the pole
#Part Product Code
A Camera VSIP4MPPTZMINI
B Camera Adapter VSBKTA107
C Wall Mount Adapter VSBKTA110
D Right Angle Bracket VSBKTB300S
E Junction Box VSBKTA140
F Pole Mount Bracket VSBKTA150
G Pole Not supplied
The installation order for mounting the junction box & camera to the pole. Note that this has
partially been assembled already:
• The camera, camera adapter, wall mount adapter are already connected (A, B, C & D).
• The junction box and pole mount bracket are already connected (E & F).

9
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
1. Mount the pole mount bracket onto the pole using 3 included band clamps (Fig. 2.3b).
Note: The 3 included band clamps are 46-70mm for poles 46-70mm in diameter. If installing on a
thicker pole (eg. 80-150mm), larger band clamps will be required.
Fig. 2.3a
Mounted pole bracket (front)
Fig. 2.3b
Mounted pole bracket (back)
Fig. 2.3c
Junction box interior (no 4G router)
2. Open the junction box (Fig. 2.3c).
Note: This image shows the inside of the junction box as seen with the WiFi kit.
The 4G kit will also have the 4G router pre-installed inside the junction box.

10
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
4. Run the power cable coming from the solar panel through one of the cable holes of the junction
box.
5. Carefully connect the solar panel power cable to the terminal block (Fig. 2.3e), with the red
wire connecting to + and the black wire connecting to -. (Fig. 2.3f)
Fig. 2.3f
Solar battery cables connected to terminal block
Fig. 2.3e
Terminal block
Caution: Do not allow the negative and positive power supply wires from the solar
panel to touch (short circuit) - this will cause the lithium polymer battery to enter protection
mode and output voltage will drop to 0V.
The only way to recover from this is to disconnect and then reconnect the battery inside the
panel - Please contact VIP Vision™ for further details.

11
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
3.1 Connect using WiFi (SLR-A75-4W)
3. Connections
1. Connect a DC jack from the terminal block to the camera.
2. Ensure the Ethernet cable is connected between the camera and the wireless bridge (station).
3. Mount the other side of the wireless bridge (access point) on the building, facing towards the
station on the solar panel.
4. The access point can be powered by one of the following methods:
a. Connect the AP’s network port to a PoE switch.
b. Connect the AP’s network port to the included PoE injector, then connect the injector to a
network switch and a 24V power supply.
5. (Optional) Connect the network switch to an NVR (The camera includes a microSD card for edge
recording).
6. (Optional) Connect the network switch to a router.
Refer to the next page for a WiFi system map example using a PoE injector.
This section covers how to set up the WiFi network for your WiFi Solar Kit. Most of the setup for the
solar panel side of the installation has already been done - it just needs to be connected to the solar
panel battery for power.
Note: The station side of the wireless bridge (IP address: 192.168.1.21) should already be mounted
under the solar panel.

12
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
Fig. 3.1a
Example WiFi Setup
NVR (optional)
Router (optional)
Internet
Network Switch
Ethernet
Power
WiFi
Wireless Bridge
(Station)
Camera
Solar Panel
Wireless Bridge
(AP)
PoE Injector
240VAC
Power

13
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
3.2 Connect using 4G (SLR-A75-4G)
1. Insert an active SIM card into the SIM slot.
2. Connect a DC jack from the terminal block to the 4G router.
3. Connect the other DC jack from the terminal block to the camera.
4. (Optional) Connect an antenna to the 4G router to improve signal strength.
NOTE: 4G setup requires an active SIM card (not included).
For more information on how to configure the 4G router, refer to the 4G router manual (included).
Camera & 4G router
connected via RJ45
4G router powered via
terminal block
Battery/terminal
block connection
Camera powered via
terminal block
Camera connected
via Ethernet cable
12VDC power
Antenna (optional)
SIM card slot
Fig. 3.2a
4G router overview
Fig. 3.2b
Connection overview

14
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
1. Install the free app from the App Store for iOS (iDMSS) or Play Store for Android (gDMSS).
2. Open the iDMSS/gDMSS you have installed on your device and select “Camera”
3. Select Menu, then select “Device Manager”. (Fig. 3.2c)
4. Press the “Add” button and tap “OK” when prompted.
5. Select “Wired device”
6. Select “P2P” & enter a name for the camera. This name is for reference only and can be set to
anything.
7. You can now select the image of the QR code and use your phone to scan the code included
with the kit.
8. Enter the default username admin and password admin123 (Fig. 3.2d). For security, be sure to
change these details before completing installation.
9. In Live Preview, you can choose between using Main or Extra stream. (Fig. 3.2e) Main displays a
higher quality stream but uses up more data and has a slower connection, while Extra consumes
less data and bandwidth but has lower image quality.
10. When using Playback, ensure that Live Preview is set to Main. If set to Extra, the screen will
be black. This is because the camera has been preset to only record the Main stream to the
microSD card (you can change this setting).
11. Select “Start Live Preview”. If the details were entered correctly, your phone should connect to
your recorder and you will see the live camera display.
For more information on how to configure the camera, refer to the camera’s Quick Start Guide
(included).
QR code remote access setup (4G)
Fig. 3.2d
Camera details
Fig. 3.2e
Live Preview stream
selection
Fig. 3.2c
Main Menu

15
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
QR code remote access setup (4G)
1. Close the junction box and securely fasten the 4 attached bolts (Fig. 3.3a).
Fig. 3.3a
Complete solar surveillance system
3.3 Finish camera installation

16
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
4.1 Setting Up 40W Motion Activated LED Light
4. Solar Panel LED Configuration (Optional)
Note: Enabling the LED light and sensor will increase power consumption and reduce battery
life.
Incorrectly editing power settings can permanantly damage the solar panel, solar
battery and/or LED light. Unless you are a professional electrician, only edit power
settings exactly as outlined in this guide.
Fig. 4.1a
Solar panel remote control
1. Ensure the solar panel battery is charged by checking that the red light on the back of the panel
is flashing/illuminated. If the light is off, take the solar panel outside and wait for it to change in
the sunlight.
2. Use the remote control and point it towards the black sensor at the back of the solar panel and
press State.
• If you hear 1 long beep, the remote succesfully received data from the panel.
• If you hear 3 quick beeps, the remote did not detect the panel.
This section covers how to set up the motion-activated 40W LED light on the solar panel. Our
example will show you how to configure your solar panel & light with the remote control, showing
you the steps required to set up the light to activate after motion is detected at night.
With this setup, the solar panel can double as a motion-actived security light at night, as well as a
network CCTV system.
The solar panel’s motion-activated LED light is disabled by default. Solar panel configuration
requires the remote control (provided on request).

17
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
Note: Intervals are periods of time set in solar panel settings that occur after the sun sets.
These periods can be set in 1 hour intervals, with a min. of 0 and max. of 3 Intervals overall.
Daytime
operation
Interval
1
Sunset
Interval
2
Interval
3
Daytime
operation
4. Adjust the following settings:
5. Point the remote control at the solar panel’s black sensor and press Send to update the solar
panel with your new configuration. If the face symbol changes to a smile, the configuration
settings were sent succesfully.
Note: To change solar panel settings back to factory default, set Re-Deflt to YES
The LED light has now been configured to activate at night when motion is detected
(as shown in the diagram below):
3. Point the remote control at the solar panel’s black sensor and press Param (Parameters) to open
the settings editing menu.
• Use the +and - keys to scroll.
• Press Set to begin editing values. The value should start flashing.
• Use the +and - keys to edit the value while it is flashing.
• Press Set again to confirm and stop editing.
• If the remote enters sleep mode from inactivity, press backL to turn it back on.
Setting Suggested
Value Description
S-Time-1 14H (Hours) The duration of Interval 1. 14H sets the LED to be active all night.
S-C-Pow1 10%
% of LED-Cur power provided to the LED upon motion detection
during Interval 1. Remains active for the duration of S-D-Time.
10% sets the LED to 10% brightness.
S-L-Pow1 0%
% of LED-Cur power provided to the LED after the last detected
motion and S-D-Time has elapsed, during Interval 1. 0% sets the
LED to turn off.
S-Time-2 0H The duration of Interval 2. 0H skips this interval.
S-Time-3 0H The duration of Interval 3. 0H skips this interval.
LED-Cur 0.15A (Amps) LED driven current. Can be set from 0.15A to 1.1A.
Warning: Do not exceed 1.1A, as this can damage the LED.
S-D-Time 20s Duration which the light stays on for after last detected motion.
Daytime operation
(Light off)
Interval 1
14 hours
(Motion activates light at 10%
brightness for 20 sec)
Sunset
Daytime
operation

18
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
4.2 Check Solar Panel Configuration
4.3 Test LED Light
1. Point the remote control at the solar panel’s black sensor and press Test.
2. Test the LED light by adjusting the light level on the remote screen with the Test button. This
scrolls through light percentages in increments of 10%. (100%, 90%, 80% etc.)
To check the solar panel’s current settings configuration, press the State button (Fig. 4.1b). This will
show info such as battery level, light activity (on/off), temperature, battery voltage, load voltage,
run time (in days), battery history and more.
Fig. 4.1b
Solar panel State menu
For more detail on editing solar panel settings, refer to the instruction manual included
with the remote control.
To the LED light system again, simply change all S-Time values (S-Time-1, S-Time-2 & S-Time-)
back to 0H.
This will skip every Interval after the sun sets, so editing other values after this point is unnecessary.
Disabling Motion Activated LED Light

19
www.vip-vision.com
SLR-A45 Series | Solar Surveillance
1. I can't connect to the camera using the QR code.
• Ensure that your camera is powered on power.
• Check that the inserted SIM card is active.
2. Video footage is slow/laggy/choppy.
• Ensure that your camera is in an area with decent mobile service coverage and that only
one user is viewing the system at once.
• Switch the stream Extra (sub) stream instead of Main to use less bandwidth.
3. My camera doesn't have power.
• Check the connections from the solar panel battery to the camera.
• If the battery is out of power, the camera should automatically turn on once the solar
panel absorbs more light.
5. Troubleshooting

20
Crucial evidence. Always.
SLR-A45 Series | Solar Surveillance
Crucial evidence. Always.
www.vip-vision.com
Note:
All products, designs and software here are subject to change without prior written notice.
Please visit our website for more information.
For more information, please visit: