ViSAGE VIS085 User manual

1 of 4 pages
Batmink Distribution, Beckery Road, Glastonbury, Somerset, Tel: [phone] www.batmink.co.uk
VIS085 6 WAY White 3W LED Pinspot Bank
Operation Manual
3W White LED Pin Spot System is the mix light with six pieces lights, which is controlled by 4 button, it is MODE,
SETUP, UP, DOWN to operation. This item has 6pcs white LED. It has program saving function. It means that the fixture
will keep the same program as the last time when you re-open the light.
Specification
LEDS: 6pcs 3W WHITE
Beam angle: 6° (standard) or 11° (accessory)
Selectable built-in programs, Auto running, dimming mode, DMX mode, slave mode, sound-activated.
Black Aluminum
Size: 800 × 90 × 230MM
Weight: 4 kgs
Power input: AC90V-240V/50HZ-60HZ
Power consumption: 18W
3PIN female XLR socket and 3PIN male XLR socket
IR remote available
Operation mode
· manual dimmer color mode
· manual select the built-in program mode
· auto run mode
· sound mode
· slave mode
· DMX mode
Here above six kinds running mode are selected by MODE button. Press MODE and SET UP button at the same time,
when it is on, you can initialize it at extra factory setting, running on the auto-run program mode. To make the display
stay on all of the time press the MODE and UP buttons at the same time. To make the display turn off after 20 seconds,
press the MODE and DOWN buttons at the same time.
1. Manual dimmer color mode
Press “MODE” button, press “SETUP” to choose the display of the white color and flash speed, when “h.XXX” is
display, press ”UP” or “DOWN” button to set the dimming rate (0-255).When “FS.XX” is display, press “UP” or
“DOWN” to select flash speed 0-99, ”0”is turn off flash.
2. Manual select the built-in program mode
Press ”MODE” button to select the built-in program mode, the LED display shows “Pr.XX”. Under this mode, press
“SETUP” button to select the program, the color jumping speed and flash speed. When “Pr.XX” is displayed, press “UP”
or “DOWN” button to set the program 1-12, total 12 programs. when “SP.XX” is displayed, press ”UP” or “DOWN” to
set the jumping speed(1-99), when “FS.XX” is displayed, press “UP” or “DOWN” to set the flash speed(0-99), ”0”is turn
off flash.
Notice: “Pr.01” is static color program. There are 2 colors to choose from. Press the SET UP button to enter the static

2 of 4 pages
Batmink Distribution, Beckery Road, Glastonbury, Somerset, Tel: [phone] www.batmink.co.uk
color submenu, the LED display shows “CL.-X” Use the UP or DOWN buttons to scroll through the static colors.
3. Auto run mode
Press “MODE” button, ”AUTO.” is displayed, the built-in programs run one after another in continuous loop. Under
this mode, press “SETUP” button to select, the color jumping speed and flash speed. when “SP.XX” is displayed, press
“UP” or “DOWN” to set the color jumping speed(1-99).When ”FS.XX” is displayed, press “UP” or “DOWN” button to
adjust the flash speed(0-99), ”0”is turn off flash.
4. Sound mode
Press “MODE” button ”SU.XX” is display, and then press “UP” or “DOWN” button to set the sound level (0-31),under
this mode, the “SETUP” button is no available.
5. Slave mode
Press “MODE” button ”SLAU.” is displayed, under this mode “ SET UP”, “UP” and “DOWN” are all not available.
6. DMX mode
Press “MODE” button, it has two mode, when “d.XXX” or”d-P.X” is displayed. Press “SETUP” to choose the DMX
address or DMX mode, when “d-P.X” is displayed, press “UP” or “DOWN” button to select the two DMX modes. When
“d.XXX” is displayed, press “UP” or “DOWN” to select the DMX address 1-512.When there is no controller signal, the
display will be flash.
1．）DMX mode 1：
CH1
0-255
Master Dimmer
Pinspot1-6
2）DMX mode2
CH1 CH2 CH3 CH4 CH5 CH6 CH7
0-255
Master
Dimmer
Pinspot1-6
0-255
Dimmer
Pinspot1
0-255
Dimmer
Pinspot2
0-255
Dimmer
Pinspot3
0-255
Dimmer
Pinspot4
0-255
Dimmer
Pinspot5
0-255
Dimmer
Pinspot6

3 of 4 pages
Batmink Distribution, Beckery Road, Glastonbury, Somerset, Tel: [phone] www.batmink.co.uk
Operation by IR remote:
You can also operate this product by IR remote, the distance available is at most 10M.
Notice: IR remote is ready to control the product which is in any working mode.
The picture of the IR remote
AUTO RUN mode
Press “AUTO RUN” to choose Auto run mode. Press FLASH to turn on/off the flash of the Auto Run, and then pressing
“+” and “-“ buttons to adjust flash speed. Press SPEED to control the speed of the Auto Run, and then pressing “+” and
“-“ buttons to adjust it.
Select program Mode
1. Press PROG to go in to set built-in program mode, and then pressing “+” or “-” to select built-in program (it is useful
without pressing FLASH /SPEED).
2. Press FLASH to turn on/off flash and press “+” or “-” to adjust the flash speed. Press SPEED to set the program
running speed and press “+” or “-” to adjust it.
Notice: “ Pr.01” is static color program. There are 2 colors to choose from. Press the SPEED button to enter the static
color submenu, and then pressing “+” and “-“ buttons to scroll through the static colors.
M/S mode
Press SL to display SLAV mode. The white lights are off when without master light.
Sound Active mode
Press SA to display sound active mode, and pressing “+” and “-” buttons to adjust sensitivity level.
Select light program mode
Press the R/G/B to choose program mode, and pressing “+” and “-” buttons to adjust the intensity of the light. Every
one of the three buttons can choose the white lights. Press FLASH to turn on/off flash effect to in this situation, pressing
“+” and “-” buttons to adjust the flash speed.
DMX MODE
Press D to display DMX mode. The white lights will flash 2~3 times. Then pressing “+” and “-” buttons to select the
two DMX modes, when the first, second and third lights are on, it is in the DMX mode 1;when the fourth, fifth and sixtth
lights are on, it is in the DMX mode 2.

4 of 4 pages
Batmink Distribution, Beckery Road, Glastonbury, Somerset, Tel: [phone] www.batmink.co.uk
Set ADDR
Press this button to set the DMX address or initialize the program, then all the white lights will flash 2~3 times. Please
put in 3 number ,for example, 1 2 3. After the first and second lights is on, please put in the first number. After the first
number is accessed the third and fourth lights will be on, then put in the second number. When the fifth and sixth lights
will be on, please put in the third number. After all the three number are put in, all the lights will flash 2~3 times, which
indicate that the DMX address is right and it go in to the DMX MODE automatically. If the address is wrong the first and
second lights will be on. New DMX address should be put in.
If the 951 are put in, all the white lights will be on.Put “0” to initialize the program. If the wrong address is put in, the fist
and second light will be on, indicating new address should be put in. Then the system will run in the designed mode.
Black Out mode
Press “BLACK OUT” to set the LED lights power on or power off by pressing this button..