Vision Fitness R2200 User manual

Assembly
Guide
R2200
SEMI-RECUMBENT FITNESS CYCLE

1
STEP
3
STEP
4
STEP
5
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
R2200
SEMI-RECUMBENT FITNESS CYCLE
2
STEP

TOOLS & PARTS INCLUDED
5MM Allen Wrench 15MM Pedal Wrench
Screwdriver
5MM L-Shaped Wrench
4MM L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Power Supply, Qty: 1
Water Bottle & Cage, Qty: 1
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card

HARDWARE INCLUDED
ORANGE BAG PINK BAG
BLUE BAG
M8 x 15L Screw
Quantity: 4 M8 Lock Washer
Quantity: 4
M8 x 15L Screw
Quantity: 3 M8 Lock Washer
Quantity: 3
M8 x 15L Screws
Quantity: 4
M6 x 55L Screws
Quantity: 8
M8 Lock Washer
Quantity: 4
M6 Lock Washer
Quantity: 8
GREEN BAG
M8 x 15L Screws
Quantity: 5
M8 x 20L Screws
Quantity: 2
M8 Lockwashers
Quantity: 6

5
1
STEP
• Slide the seat frame onto the seat rail.
• Connect the rail support to the
bottom of the seat rail. Attach with
four screws (M8x15L) and four lock
washers (M8). Tighten with the 5MM
Allen wrench.
ORANGE BAG
1
STEP
2
STEP
• Slide the front seat rail cover on the
seat rail.
• Insert the front end of the seat rail
into the frame bracket. Secure the seat
rail to the frame with three screws
(M8x15L) and three lock washers
(M8). Tighten with the 5MM Allen
Wrench.
• Slide the front rail cover into
position at the front of the seat rail.
BLUE BAG
2
STEP

6
3
STEP
• Put the seat handlebar onto the seat
frame. Attach with four screws
(M8x15L) and four lock washers
(M8), using the 5MM Allen wrench.
• Secure the seat cushions to the seat
frame by inserting the eight screws
(M6x55L) and eight lock washers
(M6). Tighten with the 4MM L-shaped
wrench.
PINK BAG
3
STEP

7
4
STEP
4
STEP
• Slide the console mast cover over
the console mast. Guide the console
cable up through the bottom of the
console mast with the attached wire.
• Slide the console mast into the con-
sole mast mounting bracket and use
the 5MM Allen wrench to secure the five
screws (M8x15L) and lock washers
(M8). Note: The screw facing the seat
does not use a lock washer. Tighten
this screw only until snug.
• Slide the console mast cover to the
proper position. Attach the front
handlebar to the console mast. Use
the 5MM Allen wrench to tighten the two
screws (M8x20L) and lock washers
(M8) to secure the handlebar.
• Take out the four screws (M5x12L)
from the back of the console with the
Phillips screwdriver. To attach the
console, plug in the console cable to
the proper position in the back of the
console. Reinsert the four screws
(M5x12L) with the Phillips screwdriver
to secure to the console mast.
• Use the Phillips screwdriver to
attach the water bottle cage to the
console mast with the two included
screws (M5x15L). Insert the water bottle.
GREEN BAG

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 6.02 Part #Z22RB58-AG1815PRD
AG18.15PRD
REV1
5
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15MM pedal wrench.
PEDALS
5
STEP