Vision Fitness R2100 User manual

Assembly
Guide
R2100 AND R2000
SEMI-RECUMBENT FITNESS CYCLES

1
STEP
2
STEP
4
STEP
5
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
R2100 AND R2000
SEMI-RECUMBENT FITNESS CYCLES
3
STEP

TOOLS & PARTS INCLUDED
5MM Allen Wrench 15MM Pedal Wrench
Screwdriver
5MM L-Shaped Wrench
4MM L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Seat Rail Cover, Qty: 1
Tension Knob and bracket, Qty: 1
(R2000 ONLY)
Water Bottle & Cage, Qty: 1
Warter Bottle Bracket, Qty:1
(R2000 ONLY)
Power Supply, Qty: 1
(R2100 ONLY)
Color-coded Hardware Bags, Qty: 1
Owner’s Guide, Qty: 1
Assembly Guide, Qty: 1
Warranty Card, Qty: 1

HARDWARE INCLUDED
ORANGE BAG
GREEN BAG
PINK BAG
M8 x 12L Screw
Quantity: 4
M8 Lockwasher
Quantity: 4
M5 x 70L Screw
Quantity: 1
(R2000 ONLY)
M8 x 15L Screws
Quantity: 5
M8 Lockwashers
Quantity: 4
M5x35L CapScrew
Quantity: 2
(R2000 ONLY)
M6 x 35L Screws
Quantity: 8
BLUE BAG
M8 x 12L Screw
Quantity: 3
M8 Lockwasher
Quantity: 3
M8 x 15L Screw
Quantity: 4
M8 Lockwasher
Quantity: 4
M6 Arc Washer
Quantity: 8
M5 Washer
Quantity: 1
(R2000 ONLY)
M5 x 15L Screws
Quantity: 2

5
1
STEP
• Slide the seat frame onto the seat rail.
• Connect the rail support to the
bottom of the seat rail. Attach with four
screws (M8x12L) and four lock
washers (M8). Tighten with the 5MM
Allen wrench.
ORANGE BAG
1
STEP
2
STEP
2
STEP
• Slide the front seat rail cover on the
seat rail.
• Insert the front end of the seat rail
into the frame bracket. Secure the seat
rail to the frame with three screws
(M8x12L) and three lock washers
(M8). Tighten with the 5MM Allen
wrench.
• Slide the front rail cover into
position at the front of the seat rail.
BLUE BAG

6
3
STEP
• Put the seat handlebar onto the seat
frame. Attach with four screws
(M8x15L) and four lock washers
(M8), using the 5MM Allen wrench.
• Secure the seat cushions to the seat
frame by inserting the eight screws
(M6x35L) and eight arc washers
(M6). Tighten with the 4MM L-shaped
wrench.
PINK BAG
3
STEP

7
4
STEP
• Slide the mast cover onto the
console mast.
• With the included wire tie, pull the
console cable, or sensor wire, through
the console mast. Place the console
mast into the console mast mounting
bracket. Secure the mast to the
bracket with 5 screws (M8x15L) and
lock washers (M8) and tighten with
the 5MM Allen wrench. NOTE: The
screw facing the seat does not use a
lock washer. Tighten this screw only
until snug. Slide the console mast
cover down over the screw heads.
• R2000 ONLY: Turn the tension knob
to level 16. Direct the cable on the
tension knob through the tension knob
bracket. Attach the cable to the
tension cable located in the console
mast. Secure the tension knob to the
console mast with the washer (M5)
and screw (M5x70L). Tighten with
Phillips screwdriver.
• Remove the four screws from the
back of the console. Plug the wire
harness into the console (For R2000
plug in RPM Sensor wire also). Mount
the console onto the console mast with
the four screws.
• R2000 ONLY: Secure the water
bottle bracket to the console mast with
the 4MM L-shaped wrench and two cap
screws (M5x35L). Attach the water
bottle cage to the bracket with two
screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
• R2100 ONLY: Attach the water
bottle to the console mast with two
screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
GREEN BAG
4
STEP R2000
R2100

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z20RB55-AG1817PRD
AG18.17PRD
REV1
5
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15MM pedal wrench.
PEDALS
5
STEP