VISIONARY DESIGNS MOD-1700 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Front View Back View
MOD-1700 Reception Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Adjust connectors if necessary to
prevent gaps in connection.
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Graphic Installation
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
CEI110 Extrusion
Profile
CEI110 Corner Connection:
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
3) Tighten all knobs to secure connection.
Disassembly:
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
All knobs must be tightened securely to ensure a proper connection.
CEI110 Frame Assembly

© 2023
Case 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Counter Top Door
1
Graphic
Setup Hardware
Level 1 (Bottom Level) Level 2 Level 3 Level 4
1A
22A
Door
Top View of Each Level
Case Packing

© 2023
Case 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
Top View of Each LevelTop View of Each Level
Assembled
Counter
Side
2-piece
Sintra
Blocker
Assembled
Counter
Side
Level 1 (Bottom Level) Level 2 Level 3 Level 4 Level 5
8,8
5
8A,8A
Shelf
Shelf
Supports
Shelf
Supports
Case Packing

© 2023
Step 1 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
*
*
1A
1
2
2A
78
8
8A
8A
7
Shelf
Support
7A
3
3A
4
5
6
Door
Door
Infill
Infill
Item
1,1A
2,2A
3,3A
4
5
6
7,7A
8,8A
Qty.
1,1
1,1
1,1
1
1
1
2,2
2,2
Description
46.25” CEI110 Horizontal Extrusion
37.5” CEI110 Vertical Extrusion
37.5” S44 Vertical Extrusion
37.5” S44 Vertical Extrusion w/ Door Hinges
37.5” S44 Vertical Extrusion w/ Door Stops
37.5” S44 Vertical Extrusion w/ Door Hinges
14.153” Z45 Horizontal Extrusion
20.408” Z45 Horizontal Extrusion
7A
*
*
Transformer
to power
++
+
-
-
-
to power
Lights
Male
Male
Female
Female
Transformer
96W / 4A / 24V
Light to Light Connection
Light to Transformer Connection
Maximum of 7 light bars per transformer.
Steps:
1) Assemble CEI110 extrusions [1] [1A] [2] and [2A], inserting
2-piece Sintra light blocker. See CEI110 Frame Assembly sheet for instruction.
2) Connect lights and transformer. See Light Connection details.
3) Attach horizontals [7] and [8] between verticals [3] [4] [5] [6] and [3A].
4) Slide infills between verticals [3] [4] and [3A] [6], making sure Velcro
is facing inward.
5) Connect doors to verticals [4] and [6]. See Door Connection detail.
6) Attach horizontals [7A] and [8A] between verticals [3] [4] [5] [6] and [3A].
7) Connect shelf supports to Velcro on infills.
Keep counter sides assembled, when packing.
Sint
r
a
Ligh
t
B
l
o
c
ker
Sint
r
a
Ligh
t
B
l
o
c
ker
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Pin
MOD-1700 Assembly

© 2023
Step 2 of 2
Order #XXXXX
Locked layer contains
placeholder marks.
*
Counter Top
Shelf
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
*
Steps:
1) Attach assembled frame to verticals [3] and [3A].
See Frame Attachment detail.
2) Install SEG graphic to front of assembled frame.
See SEG Graphic Installation detail.
3) Place shelf inside assembled base on top of pins and supports.
4) Place counter top on assembled base, then secure with pins.
See Counter Top Attachment detail.
Completed Assembly
3
3A
Attach frame to
connector on
vertical extrusion,
using bolt.
Frame Attachment
Bolt
Connector
*
*
*
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
SEG Graphic
*
MOD-1700 Assembly (cont’d)