VISIONARY DESIGNS MOD-1543 Manual

© 2019
Order #XXXXX
Locked layer contains
placeholder marks.
Perspective View
Top View
Side View
MOD-1543 Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019
Order #XXXXX
Assembly Assembly Cont’d
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push pin lock into hole of connecting frame.
Note: Block on pin lock will secure in groove.
Pin Lock
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
Graphic Removal
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternate corner, then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
Gravitee & SEG Assembly Instruction

© 2019
Order #XXXXX
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
LT Panel Assembly Instruction

© 2019
Case 1 of 1
Order #XXXXX
Top View of Each Level
Level 2
Counter Top
1& 3 6 & 4Wing2
Level 3 Level 4 Level 5
Level 1 (Bottom Level) Level 6
Setup
Hardware
(2) Shelves
5
Case Packing

© 2019
Step 1 of 1
Order #XXXXX MOD-1543 Assembly
Locked layer contains
placeholder marks.
3
3
3
Door
Door
2
1
1
1
6
5
4
Shelf
Gravitee Lighbox
Shelf
FRONT VIEW BACK VIEW BACK VIEWBACK VIEW
Gravitee Lighbox
Wing
Counter Top
Pin
Pin
Pin
Pin
Pin
Pin
Literature
Holder
Item
1
2
3
4
5
6
--
--
--
--
--
Qty.
1
1
1
1
1
1
1
2
6
1
1
Description
18” x 37.5” LT Panel w/ 37.5“ S10
Gravitee Lightbox w/ 37.5” End Caps
18” x 37.5” LT Panel
12”
90° LT Connector w/ 25.5“ End Cap
21.375” x 12” Door
12”
90° LT Connector w/ 25.5“ End Cap
Literature Holder
Shelf
Pin
Counter Top
Wing
Steps:
See reverse side LT Panel Assembly instruction for
steps 1, 2, and 3.
1) Connect Gravitee lightbox [2] to panels [1] and [3].
See reverse side for LT Panel Assembly instruction.
2) Install SEG graohic to Gravitee Lightbox. See Gravitee & SEG
Assembly Instruction sheet.
3) Attach connectors [4] and [6] to door.
4) Attach door assembly to panels [1] and [3].
5) Place pins into panels [1] and [3] then set shelves onto pins.
6) Attach literature holder to panel [1].
7) Lock counter top to panels [1] and [3]. See Counter Top Lock detail.
8) Attach wing to Gravitee lightbox.
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Lock
12
*
Pin
Hole
SEG Graphic