VISIONARY DESIGNS MOD-1177 User manual

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1177 -
Kiosk Assembly
Item
10
11
12
13
Qty.
1
1
1
1
Steps
1)
Attach vertical extrusions [11,13] to base plate [10] with bolt.
2) Insert connection bar into vertical [11] and secure with set
screws.
3) Connect vertical [12] to connection bar inserted into vertical [11]
and secure with set screws.
4) Attach tapered plex wing to front of vertical [13] using screw caps.
5) Attach counter top to vertical extrusion [13].
6) Attach monitor mount to vertical [12] with screws as shown.
7) Attach round sign to vertical [12] with stand-off barrels and screw
caps.
Description
23”D Round Base Plate
40”h Lower Round Vertical Extrusion
40”h Upper Round Vertical Extrusion
36”h Round Vertical Extrusion
10
11
13
Screw
Cap
Secure sign to
stand-off barrels using
screw caps
Sign Attachment
stand off
barrel
Slide stand-off barrels
into groove of vertical
extrusion
12
13
12
11
Sintra Sign
Monitor Mount
Attachment
Attach back plate
to connectors using
screws. Attach top
plate and tighten
setscrews to secure.
Slide connectors
into groove of
extrusion. Tighten
setscrew to secure
in place.
Setscrews
Stand-off
Barrel
Screw
Cap
Screws
Connector
Screws
Vertical Connection
*
*

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1177 - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1177 -
Case Packing
Round Base Plate
Setup Hardware
Round
Sintra Sign
Wings
Counter Top
Level 1 Level 2 Level 3
13
11 12