VISIONARY DESIGNS GOD-1558 Manual

© 2018
Order #XXXXX
Plan View
Back Side
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
GOD-1558 Reception Counter

© 2018
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2018
Order #XXXXX Gravitee Panel Assembly
Assembly Assembly Cont’d
Stacking Unstacking
Stacking Assembly
1) Place one horizontal frame on top of the other, lining up the
center grooves.
2) Turn stacking lock clockwise to tighten into place. Repeat
for each lock.
Stacking Disassembly
1) Turn the stacking lock counter-clockwise to loosen.
2) The whole spring on the stacking lock should be in view to
release each frame. The disengaged spring should release
the stacking lock. If not, keep turning the stacking lock until
it disengages.
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push stacking lock into the slot
of the upper frame, then spin the
cap to tighten the lock.
Push pin lock into hole of connecting frame.
Note: Block of pin lock will secure in groove.
Disengage the stacking lock by
spinning the cap counter
clockwise and pulling down.
Cap
Stacking
Lock
Pin Lock
Top View
Corner Connector
SEG
Grooves
Note: Orientation of Corner
Connector may change.

© 2018
Step 1 of 2
Order #XXXXX Reception Counter Assembly
Door
Door
3
1
2
door hinge
4
2
Item
1
2
3
4
5
6
7
8
9/9A
10
Qty.
1
1
1
1
1
1
1
1
1/1
1
Description
38”h Gravitee Corner Post w/ Door Attachment
14.125”w x 38”h Gravitee Panel Frame
38”h Gravitee Corner Post
19”w x 38”h Gravitee Panel Frame
19”w x 38”h Gravitee Panel Frame
38”h Gravitee Corner Post
14.125”w x 38”h Gravitee Panel Frame
38”h Gravitee Corner Post w/ Door Attachment
37.0945”w Z45 Horizontal Extrusion
34.4173”h Z45 Vertical Extrusion
Steps:
1) Assemble Gravitee panels and posts in numerical order.
See Gravitee Panel Assembly sheet for details.
2) Attach horizontal extrusions [9] & [9A] between posts [1] & [8].
3) Connect vertical [10] between horizontals [9,9A].
4) Install Cabinet Doors. See Door Attachment detail.
1
2
3
4
5
6
7
8
9
9A
10
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
door hinge
8
6
7
5
7
BACK SIDE
BACK SIDE
*
*
*
*

© 2018
Step 2 of 2
Order #XXXXX Reception Counter Assembly (Cont’d)
*
Shelf Supports
attach with Velcro
Shelf Supports
attach with
Velcro
Completed Assembly
Shelf
Counter Top
Steps:
1) Wrap SEG Graphic around front & sides of counter.
See SEG Graphic Installation detail.
2) Attach shelf supports to Velcro, then place shelf on top of supports.
3) Place counter top on assembly. See Counter Top Attachment detail.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
Back View Front View
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
*
Top View

© 2018
Case 1 of 2
Order #XXXXX Case Packing
Top View of Each Level
Level 2Level 1 Level 3 Level 4 Level 5 Level 6
9 9A
10
Door
Door
Shelf
Counter Top
1 6 3 8
Shelf Supports

© 2018
Case 2 of 2
Order #XXXXX Case Packing
Top View of Each Level
Level 2Level 1 Level 3 Level 4
57 24