VISIONARY DESIGNS RE-2029 User manual

Step 1
Page 1 of 9
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
RE-2029 General Layout
Plan View
Elevation View
Perspective View
20’
10’

Step 2
Page 2 of 9
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C El iateDDl i ateDDetail B
Detail A
Setscrews

Step 1
Page 1 of 9
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
RE-2029 Backwall Assembly
Steps:
1) Attach lower vertical extrusions [2,3,6] to base plates [1].
2) Attach upper vertical extrusions to lower vertical extrusions as shown.
3) Connect horizontal extrusions between vertical extrusions as shown.
4) Apply graphics to velcro on back of assembled backwall.
Item Qty Description
1 3 Base Plate
2/2a 1/1 41.875” S40 Vertical Extrusion
3/3a 1/1 41.875” S40 Vertical Extrusion
4/4a 1/1 42” S40 Vertical Extrusion
5/5a 1/1 42” S40 Vertical Extrusion
6 1 41.75” S40 Vertical Extrusion
7 1 42” S40 Vertical Extrusion
8a/8b 1/1 41.906” Z45 Horizontal Extrusion
9a/9ba 1/1 41.906” Z45 Horizontal Extrusion
10/10a 1/1 36” Z45 Horizontal Extrusion
11/11a 1/1 22” Z45 Horizontal Extrusion
12a/12b 1/1 30” Z45 Horizontal Extrusion
13a/13b 1/1 30” Z45 Horizontal Extrusion
Attach graphics
to velcro on back of
assembled backwall
1
2
2a
3a
3
4a
4
5a
5
6
7
8a
8b
10
10a
11
11a
S40
12a
12b
13a
13b
9a
9b
11
Velcro
PR37
Extrusion
Profile
Slide PR37 extrusion into
groove of vertical and tighten
set screw to secure in place.
Extrusion
Profile
Extrusion
Profile
Z45
Velcro
BACK VIEW
FRONT VIEW
Velcro
Velcro
Velcro
Velcro
Velcro

Step 2
Page 2 of 9
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
RE-2029 - Counter Assembly
Steps
1) Attach horizontal extrusions [15] between vertical
extrusions [4 & 14] and [5 & 14a] inserting infills as shown.
2) Attach door to hinges as shown in detail.
3) Velcro shelf support to inside of pedestal, then set
internal shelf on top of supports.
4) Place counter top on assembled pedestal.
5) Attach plex shelf to countertop with
standoffs as shown in detail.
Door
Insert Insert
14
14a
15
15
15
15
16
16
4
5
4a
5a
Counter Top
Plex
Shelf
Internal Shelf
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Extrusion
w/Door Hinges
Item Qty Description
14/14a 1/1 38” Vertical Extrusion
15 4 12.5” Horizontal Extrusion
16 2 Curved Extrusion
Attach standoff barrels to counter
and secure in place. Secure upper
shelf to standoffs using screw caps.
Plex Shelf to Counter Attachment
Upper Shelf -
Clear Plex
Threaded hole
in counter top
Standoff
Barrel
Screw
Cap

Step 3
Page 3 of 9
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
RE-2029- Attachments Assembly
Steps
1) Connect canopy pieces together using bolts and wing nuts provided, see Example of Canopy Connection detail.
2) Connect header extrusions [18a,18b,19a,19b,20a,20b] together as shown.
3) Attach header & canopy to assembled backwall as shown in detail.
4) Attach wings using A10 clamps as shown.
5) Attach round graphic signs to backwall with standoffs as shown in detail.
6) Attach iPad clamshells to backwall as shown in detail.
7) Attach literatrure rack as shown in Literature Rack Attachment detail.
Secure with
wing nut
Connect 3 piece Canopy
together by using bolts and
wing nuts provided.
Bolts
Connecting
Canopy Pieces
Together
Example of Canopy Connection
18a
A
B
C
18b
19a
19b
20a
20b
18a 18b
19a
19b
20a
20b
Bolt
Wing Nut
Header Attachment
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
Item Qty Description
18a/18b 2/2 39” Vertical Extrusion
19a/19b 2/2 5.862” Horizontal Extrusion
20a/20b 2/2 38.5” Curved Extrusion
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion and
twist to secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
*
*
*
*
Tighten Lock
to Secure
Swivel
Mounting
Plate
iPad Mount Attachment
*
*
**
*
*
Attach connector piece to iPad
mount as shown. Then connect
assembled iPad mount to vertical
extrusion.
Attaching Graphics
Attach Header Graphic to Back of
assembled header frames.

Step 4
Page 4 of 9
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Steps
1) Attach lower horizontal extrusions [5,6,7] between
vertical extrusions [1,2,3,4] as shown.
2) Hang assembled door on hinges on vertical [1] as shown. Refer to detail.
3) Place side and front inserts between verticals as shown.
4) Attach upper horizontal extrusions [5,6a,7] between
vertical extrusions [1,2,3,4] and on top of infills as shown.
5) Velcro shelf support to inside of pedestal, then set internal
shelf on top of supports.
6) Place counter top on assembled pedestal.
Item Qty. Description
1 1 38“ Vertical Extrusion w/ Door Hinges
2 1 38” Vertical Extrusion w/ Door Stop
3 1 38“ Vertical Extrusion
4 1 38” Vertical Extrusion
5 2 22.0197“ Horizontal Extrusion
6/6a 2/2 12.5” Horizontal Extrusion
7 2 25.639“ Curved Extrusion
Door
Insert
Insert
Insert
1
2
4
4a 3
3a
5
5
7
7
6
6
6a
6a
Counter Top
Internal Shelf
Extrusion
w/Door
Hinges
Shelf
Supports
RE-2029 Pedestal Assembly