VISIONARY DESIGNS VK-2921 Manual

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
10’
20’
Plan View
VK-2921 - General Layout

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 3
Page 3 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Q914 Connections
If the locks are set too far forward, the lock will not
fully engage.
Turn the set screw clockwise to move the lock
back into the extrusion, counter-clockwise
to move the lock outward.
The lock should be set back about 1 mm
(1/16”) from the edge of the extrusion for
the locks to engage properly.
When the lock is properly engaged, the
extrusions will fit tightly together.
When the lock is properly engaged, the
extrusion will not move.
Turn the hex wrench clockwise to open the
lock and secure in the groove.
1
2
3If the locks are not properly engaged, gaps
will be noticable and the extrusion will be
loose.

www.classicexhibits.com
Step 4
Page 4 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - SEG Graphic Installation
Graphic Removal
Graphic: To Ensure Proper Fit
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternater corner then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
SEG Graphic Installation

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Room Assembly
Item Qty. Description
1 1 96” Q914 Vertical Extrusion
2 1 96” Q914 Vertical Extrusion
3 1 96” S44 Vertical Extrusion
4 1 96” S44 Vertical Extrusion
5 1 96” Q914 Vertical Extrusion w/Door Hinges
6 1 96” Q914 Horizontal Extrusion w/Door Stop
7 4 25“ Z45 Horizontal Extrusion
8 6 22.1265” Z45 Horizontal Extrusion
9a/9b 1/1 70” Z45 Horizontal Extrusion
1
7
7
7
7
8
8
8
8
8
8
2
3
4
5
5
Door
6
9b
9a
Steps:
1) Slide Door Threshold into bottom of verticals [5,6] as
shown in detail.
2) Connect horizontals [7] between verticals inserting
infills as shown.
3) Connect horizontals [8] between verticals, inserting
infills as shown.
4) Connect horizontals [9a,9b] between verticals [1,6].
5) Hang assembled door to vertical [5] as shown in detail
6) Attach backer fabric to front of backwall
as shown.
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Door
Hinge
Hinge
Door Threshold
Tighten
to secure
Slide into
groove
Velcro:
Bottom Edge
Velcro:
Top Edge

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Assembly
Steps:
1) Connect verticals [11,12] to baseplates [10] with bolts as shown.
2) Connect horizontals [13a,13b] between verticals [11,12].
3) Connect horizontals [14a,14b] between verticals [6,12].
4) Attach graphics to SEG groove on assembled backwall as
shown in general information pages.
11
12
6
10
10
13a
13b 14b 14b
14a
14a
Item Qty. Description
10 2 Base Plates
11 1 96” Q914 Vertical Extrusion
12 1 96” Q914 Vertical Extrusion
13a/13b 1 23” Z45 Horizontal Extrusion
14a/14b 1 50” Z45 Horizontal Extrusion
SEG Groove faces front
SEG
Extrusion
Profile
Slide SEG extrusion into
groove of vertical and tighten
set screw to secure in place.

www.classicexhibits.com
Step 3
Page 3 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Large Ceiling Assembly
Item Qty. Description
15/15a 2/2 55.945” S40 Horizontal Extrusion
16 2 19.874” S40 Horizontal Extrusion
17 4 19.874” Z140 Horizontal Extrusion
Steps:
1) Attach horizontals together inserting infills as shown.
2) Attach assembled ceiling to top of storage room extrusions
using bolts as shown.
15
15
15a
16
16
17
17
17
17
15a
Infill Infill Infill Infill Infill
Puck Light
Ceiling Attachment
Attach horizontal extrusions to top of
storage room extrusions with
bolts as shown.

www.classicexhibits.com
Step 4
Page 4 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Small Ceiling Assembly
Item Qty. Description
16 2 19.874” S40 Horizontal Extrusion
17 1 19.874” Z140 Horizontal Extrusion
18 2 30.165” S40 Horizontal Extrusion
Steps:
1) Attach horizontals together inserting infills as shown.
2) Attach assembled ceiling to top of Backwall extrusions
using bolts as shown.
16
16
18a
18
17
Infill Infill
Ceiling Attachment Example
Attach horizontal extrusions
to top of backwall
extrusions with
bolts as shown.

www.classicexhibits.com
Step 5
Page 5 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Attachments
Steps:
1) Attach lights to top of backwall as shown.
2) Attach monitor mount and monitor mount plate
to verticals as shown in detail.
3) Attach Wings to A-10 clamps as shown.
4) Attach graphic signs to Velcro on verticals as shown.
*
**
Monitor Mount
Attachment
Graphic
Sign
Graphic
Sign
Wings
Wings
Attach back plate to connectors
on vertical extrusion using screws.
Then attach monitor mount and
tighten setscrews to secure.
Slide mounting connector
pieces into groove of
extrusion. Tighten setscrew
to secure in place.
Monitor
Mount
Back
Plate
When desired location
is found, tighten
set screw to secure.
Tighten knob to
secure shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Attachment

www.classicexhibits.com
Step 6
Page 6 of 6
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Pedestal Assembly
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Steps
1) Attach lower horizontal extrusions [23,24,25] between
vertical extrusions [19,20,21,22] as shown.
2) Hang assembled door on hinges on vertical [19] as shown. Refer to detail.
3) Place side and front inserts between verticals as shown.
4) Attach upper horizontal extrusions [23,24,25] between
vertical extrusions [19,20,21,22] and on top of infills as shown.
5) Velcro shelf support to inside of pedestal, then set internal
shelf on top of supports.
6) Place counter top on assembled pedestal.
Item Qty. Description
19 1 38“ Vertical Extrusion w/ Door Hinges
20 1 38” Vertical Extrusion w/ Door Stop
21 1 38“ Vertical Extrusion
22 1 38” Vertical Extrusion
23 2 22.0197“ Horizontal Extrusion
24 4 12.5” Horizontal Extrusion
25 2 25.639“ Curved Extrusion
Door
Insert
Insert
Insert
19
20
22
22a 21
21a
23
23
25
25
24
24
24
24
Counter Top
Internal Shelf
Extrusion
w/Door
Hinges
Shelf
Supports
Qty 3

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Crate Packing