Vivo DESK-EV00W User manual

White Electric Single Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
SKU: DESK-EV00W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
https://vivo-us.com/products/desk-ev00w

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
PACKAGE CONTENTS
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
NOTE: SOME HARDWARE INCLUDED MAY NO BE USED
A (x4)
M8x47
B
M6x10
C(x14)
M6x12
D(x16)
M5x16
F(x4)
Foot Pad
G (x2)
Cable Clip
H
2mm, 4mm, 5mm
Allen Wrench
1(x1)
Desktop
(not included)
2(x1)
Control Panel
3(x2)
Side
Bracket
4 (x1)
Crossbar
End Set
5
Leg
6(x1)
Leg with Motor
7(x2)
Foot
8 (x1)
Crossbar
9
Sync Rod
10 (x1)
Power Adapter
11 (x1)
Power Strip
Tray
E(x12)
Anti-Vibration
Pads

3
6
5
4
ASSEMBLY STEPS
STEP 1
H=
Assemble the crossbar ends (4) to the legs (5, 6) using M8x47 bolts (A). Ensure the ends are facing in
the same directions as the motor and hex socket, and tighten the bolts using the 5mm Allen wrench
(H). Mount the side brackets (3) to the legs, making sure the top is facing away from each crossbar
end, using M6x10 bolts (B). Tighten with the 4mm Allen wrench (H).
56
3
H=
1
2
3
4
5
6
7
8
9
10
11
12

4
STEP 2
Place the feet (7) on the legs as shown, then insert and tighten M6x12 bolts (C) using the 4mm Allen
wrench (H).
STEP 3
Insert the crossbar (8) into the crossbar ends (4).
H=
8
4
7

5
STEP 4
Screw the foot pads (F) into the feet. Insert M6x12 bolts (C) into the crossbar ends using the 4mm
Allen wrench (H). Do not tighten at this time.
STEP 5
Loosen the nut on the sync rod (9). Insert the sync rod’s hex sha into the socket of the
non-motorized leg, then extend the rod onto the motor coupling. Tighten the set screw on the sync
rod coupling using the 2mm Allen wrench (H), but do not yet tighten the nut.
Install the Anti-Vibration Pads (E) as shown below.
H=
H=2mm
E
9
F

6
STEP 6
Hang the power strip tray (11) over the crossbar. Adjust the frame length to fit the desktop (1), then
secure to the desktop using M5x16 screws (D) with a Phillips screwdriver. Tighten the sync rod nut and
previously inserted M6x12 bolts (C).
STEP 7
Attach the Control Panel to the desk using M5x16 screws (D). Connect the motor and power adapter
(10) to the control panel (2). Tidy up cables using Cable Clips (G).
11
1
C
D
M5×16 10PCS
5x16 4PCS
D
G
10
2

7
STEP 8
Carefully flip the assembled desk right side up and plug the power cord into an AC electrical outlet. If
necessary, adjust foot pads to level the desk.
The desk is now ready for use. Please refer to the Controller User Guide for operational instructions.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.

LAST UPDATED: 06/02/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303