Vivo DESK-V103EW User manual

White Electric Dual Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v103ew
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: DESK-V103EW

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B(x2)
Side
Bracket
C(x2)
Foot
S-A (x8)
M6x12 Bolt
S-B x8 )
M6x16 Bolt
S-C (x10)
7/8" Screw
S-D (x2)
3/4" Screw
H(x2)
Hook
D (x2)
Shelf
E (x2)
Liing
Column
F (x1)
Fixing Plate
G (x1)
Control Unit
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
S-E (x2)
M4x6 Flat Head
Bolt
S-F (x4)
M4x6 Bolt
I(x1)
Power Cable
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
J (x1)
Control
Panel
S-G (x3)
Cable Clip
S-H x10)
Anti-Vibration
Pad
S-I (x1)
Allen Wrench

3
TOOLS NEEDED
275lbs
(124.74kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
STEP 2
Place the side brackets (B) upside down on a flat surface, then place telescopic crossbar (A) over the
brackets as shown, making sure the screw posts on the brackets fit into the holes in the crossbar (A).
Phillips
Screwdriver
Level Drill
Loosen the eight screws on the crossbar using the Allen wrench (S-I).

4
STEP 3
Drill pilot holes under the desktop with a 1/8” drill bit, then remove the crossbar with brackets. Do not
drill holes deeper than 1/8”.
STEP 5
STEP 4
Tighten all screws with the Allen wrench (S-I) to secure length.
Place the crossbar with brackets on the desktop. Adjust the length to suit the desktop.

5
STEP 6
Attach the legs (E) to the assembled frame using M6x12 bolts (S-A). Tighten with the Allen wrench
(S-I). NOTE: Insert all necessary screws into holes before completely tightening.
STEP 8
Attach the fixing plate (F) to the crossbar using M4x6 flat head bolts
(S-E) with a Phillips screwdriver.
STEP 7
Place the feet (C) on the legs as shown. Insert the M6x16 bolts (S-B) as shown and tighten with the
Allen wrench (S-I).

6
STEP 9
Connect motor cables, control panel (J) and power cable (I) to the control unit (G).
STEP 10
Slide the control unit onto the fixing plate as shown.
STEP 11
Fix the hooks (H) to the shelf (D) with M4x6 bolts and tighten with a Phillips screwdriver. Hang the shelf
onto the frame as shown, then tighten installed thumbscrews to secure. Press anti-vibration pads
(S-H) into desktop mounting holes.

7
STEP 12
Attach the desktop with 7/8" screws (S-C). Attach the control panel to the desktop with 3/4"
screws (S-D). Tighten all screws. Add cable clip (S-G) to organize. Connect the power cable
to a wall outlet to power on desk for operation.
Each foot pad can be adjusted independently for fine tuning. Slightly turn the foot pad to
lower or raise the base. Use a level to ensure the desktop is even.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.

Last Updated: 08/12/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654