Vivo DESK-V402P V402P User manual

Stud Des and Chair
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model DES V402P
B3 (x1)
Rea Suppo Ba
Tools Required
phillips screwdriver
Pa age Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
A1 (x12)
Plasi Washe
A2 (x8)
Sho Bol
A3 (x4)
Sew
A4 (x4)
Lo Nu
A5 (x4)
Lon Bol
A6 (x2)
Kno
A7 (x1)
Allen Wenh
A8 (x1)
Hoo
B1 (x1)
Chai Le
B2 (x1)
Cene Ba
B4 (x1)
Plasi Sea
Boom
B7 (x1)
Des Suppo Ba
B8 (x1)
Des
B6 (x1)
Des Les
- -https//vivo us. om/produ ts/des v402p
B5 (x1)
Plasi Sea Ba

Chair Assembl Steps
2
Step 1
Step 2
Attach rear support bar (B3) to back of chair legs (B1) using 4 short bolts (A2) and 4
plastic washers (A1), leaving the bolts slightly loose. Place center bar (B2) into large
holes on left and right chair legs (B1), then tighten bolts on rear support bar using
the Allen wrench (A7).
Mount plastic seat bottom (B4) to assembled frame using 4 plastic thread screws
(A3). Tighten with Phillips screwdriver.
Step 3
Step 4
Step 5
Slide plastic seat back (B ) onto
chair frame, aligning upper or lower
holes in seat back with screw holes
in frame depending on the needed
height.
Secure seat back using knobs (A6).
Adjust chair feet to sit level if needed.

Step 8
Step 9
Squeeze sides of hook (A8) and fit into slot on left or right side of desk.
Loosen knobs on sides of desk to raise the desktop, then secure desk to frame
using 4 long bolts (A ) with 4 plastic washers (A1) and 4 lock nuts (A4), and tighten
with the Allen wrench.
Step 6
Step 7
Des Assembl Steps
Attach desk support bar (B7) to back of desk legs (B6) using 4 short bolts (A2) and 4
plastic washers (A1), then tighten bolts on rear support bar using the Allen wrench
(A7).
Adjust legs to equal height using the indicators on the sides as a reference, then
place desk (B8) on legs.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safet Warning
Conta t us at
Last updated: 07/2 /18
Step 10
Step 11
Step 12
Raise: Loosen knobs/screws on back of desk/chair legs. Step on support bar with
one foot and pull up with even motion on both sides until the desk/chair reaches
desired height. Tighten knobs or screws. Lower: Loosen knobs/screws on back of
desk/chair legs. Step on support bar with one foot and pull up with even motion
until the desk/chair reaches max height, then fully lower. Tighten knobs or screws.
Loosen knobs on sides of desk
to adjust desktop tilt angle, and
tighten knobs to secure position.
Adjust desk feet to sit level if needed.
4