Vivo DESK-SKIRT-71 User manual

71” Cable Management
Desk Organizer
Instruction Manual
SKU: DESK-SKIRT-71
Assembly Video & Product Info
www.vivo-us.com/products/desk-skirt-60

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact
our product support team at 309-278-5303 or [email protected] for further assistance. Check carefully to make sure
there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this
product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be
liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S

3
Phillips
Screwdriver
Power
Drill
Pencil
Package Contents
Tools Needed:
Included Hardware
B (x2)
Side Bar
W-A (x1)
3/4” Screw
D (x3)
Mounting Clip
E (x6)
Upper/Lower
Bar
G (x4)
Joiner
A (x1)
Panel
C (x4)
T Joiner
F (x2)
Middle
Bar

4
ASSEMBLY STEPS
STEP 1
F
GC
E
B
C
Connect the centers of the T Joiners (C) to the ends of the Middle Bars (F).
Connect the Upper/Lower Bars (E) to the sides of the T Joiners (C), then connect the
Joiners (G) and Side Bars (B) to the sides to complete the frame assembly. Lighty tap each
joint against a hard surface to ensure all bars and joiners are full pressed in.
[ CLOSE UP VIEW OF HALF OF ASSEMBLY ]
Note: Ensure all bars and joiners are fully pressed in for a secure fit

5
STEP 2
Open the flap and straps of the Panel (A) and insert the frame, making sure the frame is
fully inserted and the material is tightly stretched around it.
Snug Fit:
Fabric on Panel has a tight fit around the frame and may need to be
stretched before inserting the frame.
A
Note: Confirm that frame pieces are fully secure into each other before sliding into
panel.
Fasten Straps (A1) on inside of Panel (A) to secure the frame.
A1
A

6
S-A (x1)
STEP 3
STEP 4
Place the plastic Mounting Clips (D) in the center of each exposed portion of the
steel bars.
NOTE: Make sure the wire
management flap on the
Panel (A) is facing the
inside of the desktop. D
A
NOTE: Make sure the mesh flap on Panel (A)
is facing the inside of the desktop.
Center the assembled panel under the desktop and use a pencil to mark the locations of
Plastic Mounting Clips (D). NOTE: Desktop must be at least 1” thick to prevent screws from
poking out through the top and damaging the surface.
A
D

7
STEP 5
Drill pilot holes using a 1/8” (3mm) bit. Mount the assembled panel to the underside of
the desk using 3/4” Screws (W-A) as shown into Plastic Mounting Clips (D).
W-A
D
A
Route and organize the cables and secure them using the flap on Panel (A).

LAST UPDATED: 01/08/24
REV1.1
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us