Vivo STAND-RACE1SF User manual

Shelf Kit for STAND-RACE1B
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-race1sf
SKU: STAND-RACE1SF
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
77lbs
(35kg)
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please contact our product support team at 309-278-5303 or [e-mail] for further assistance.
Check carefully to make sure there are no missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CPU Shelf Side Shelf

3
TOOLS NEEDED
Phillips
Screwdriver
NOTE: SOME HARDWARE MAY NOT BE USED
A (x1)
CPU Shelf
B (x1)
Side Shelf
C (x2)
CPU Arm
T-A (x1)
5mm Allen
Wrench
D (x1)
CPU Center
Post
E (x1)
Side Shelf
Center Post
F (x1)
Side Shelf
Arm
G (x2)
Arm Bracket
S-A (x16)
ST4.8x13mm
Screws
S-B (x2)
M6x12mm
Screw
S-C (x4)
M8x16mm
Screw
PACKAGE CONTENTS

4
ASSEMBLY STEPS
STEP 1
Secure CPU Center Post (D) to underside of CPU Shelf (A) using ST4.8x13mm Screws (S-A)
and a Phillips screwdriver.
Take note of the pilot hole patterns on CPU Shelf (A) and Side Shelf (B). Identify CPU Shelf
for use below.
A
D
S-A
A
CPU Shelf
B
Side Shelf

5
STEP 2
Secure CPU Arms (C) to the underside of CPU Shelf (A) using ST4.8x13mm Screws
(S-A) and a Phillips screwdriver.
C
A
S-A

6
STEP 3
Use 5mm Allen Wrench (T-A) to loosen the two screws on the front support frame of your
VIVO racing cockpit so that they protrude 5mm from the frame.
Line up CPU Arm (C) keyholes with the previously loosened screws and slide into place.
Tighten screws using 5mm Allen Wrench (T-A).
T-A
C
T-A

7
STEP 4
Fasten Arm Brackets (G) to the back of CPU Arms (C) using M8x16mm Screws (S-C) and
5mm Allen Wrench (T-A).
T-A S-C G
C

8
STEP 5
Remove the M8x16mm screws from the underside of cockpit’s rear support bar
using 5mm Allen Wrench (T-A).
Line the Side Shelf Arm (F) on the underside of the rear support bar and re-thread the
previously removed screws into the frame. Secure using 5mm Allen Wrench (T-A).
T-A
T-A
F

9
STEP 6
Use a Phillips screwdriver and M6x12mm Screws (S-B) to attach Side Shelf Center Post (E)
to Side Shelf Arm (F).
E
F
S-B

10
STEP 7
Fasten the Side Shelf (B) to Side Shelf Arm (F) using ST4.8x13mm Screws (S-A) and a
Phillips screwdriver.
B
F
S-A