Vivo DESK-EV02RW User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-ev02rw
SKU: DESK-EV02RW
White Electric Dual Motor Desk Frame
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B(x2)
Side
Bracket
C(x2)
Liing
Column
G(x1)
Power
Cable
D (x2)
Foot
E (x1)
Fixing Plate
F (x1)
Control Unit
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK,
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO
REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
S-F (x3)
Cable Clip
H(x1)
Control Panel
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-G (x12)
Anti-Vibration
Pad
S-H x1)
Allen Wrench
S-B x8 )
M6x16 Bolt
S-A (x8)
M6x10 Bolt S-C (x12)
3/4" Screw
S-D (x5)
3/4" Screw
S-E (x2)
M4x6

3
TOOLS NEEDED
275lbs
(125kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Insert anti-vibration pads (S-G) into the mounting holes on top of the telescopic crossbar (A) and side
brackets (B). Insert the side brackets into ends of the crossbar and place upside down on the desktop.
Phillips
Screwdriver
Level
Drill
PLUGGED IN
176lbs
(80kg)
UNPLUGGED
NOTE: If the desk is unplugged, it may cause the leg to
slip to lower heights if the desk is overweight.

4
STEP 3
Loosen the set screws in the telescopic
crossbar (A) using the Allen wrench (S-H),
then extend the crossbar length to fit the
desktop. Retighten the set screws with the
Allen wrench (S-H).
STEP 2
Place the liing columns (C) into the telescopic
crossbar (A) and secure using M6x10 bolts (S-A)
and the Allen wrench (S-H). Assemble the feet (D)
to the columns using M6x16 bolts (S-B) and the
Allen wrench (S-H).

5
STEP 4
STEP 5
Place the control panel (H) at the desired location and mark drilling locations with a pencil. Drill 5/8"
(16mm) deep pilot holes under the desktop with a 5/64" (or 2mm) drill bit. Attach the control panel (H)
to the desktop with 3/4" screws (S-D) using a Phillips screwdriver.
Drill 3/8” (10mm) deep pilot holes using a 3/32” (or 3mm) drill bit. Secure the frame to the desktop
using 3/4” screws (S-C) with a Phillips screwdriver.

6
STEP 7
Connect motor cables, control panel (H) and power cable (G) to the control unit (F). Determine
the locations for the cable clips (S-F) and drill 5/8" (16mm) deep pilot holes under the desktop
with a 5/64" (or 2mm) drill bit. Mount the clips to the desk using 3/4” screws (S-D) with a Phillips
screwdriver, and use the clips to organize the cables.
STEP 6
Attach the fixing plate (E) to the telescopic crossbar (A) using M4x6 bolts (S-E) with a Phillips
screwdriver. Slide the control unit (F) onto the fixing plate.

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
STEP 8
Connect the power cable (G) to a wall outlet to power on desk for operation.
Each foot pad can be adjusted independently for fine tuning. Slightly turn the foot pad to lower or
raise the base. Use a level to ensure the desktop is even.

LAST UPDATED: 07/10/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303