Vivo PS-E-100V User manual

Electric Projector Screen
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/ps-e-100v
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: PS-E-100V

2 3
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
ASSEMBLY STEPS
WARNING: FOLLOW INSTRUCTIONS TO PREVENT PRODUCT DAMAGE AND/OR PERSONAL INJURY:
• DO NOT FOLD SCREEN
• DO NOT USE FINGERS OR HARD OBJECTS TO TOUCH SCREEN SURFACE
• DO NOT SPLASH LIQUIDS OR CHEMICALS ON SCREEN SURFACE
• KEEP SCREEEN AWAY FROM HOT OBJECTS OR FIRE
PACKAGE CONTENTS
Electric Projection
Screen Unit
Remote Control Wall
Mount Caddy
Remote Control
NOTE: Hooks not included
STEP 1
OPTION A: Wall Installation
Insert screws in wall directly for wood studs. If anchors are needed, press anchors into holes rst and
insert screws into anchors. Screw heads should be spaced about 1/4” from the wall.
Carefully line up mounting holes on projector screen with screw heads, and hang in place making sure
slots are fully seated over screw heads.
STEP 2
Drill holes in wall or ceiling to match the distance
between mounting holes or hooks on the
screen. Using a level for drilling holes in wall is
recommended.
NOTE: Use a 3/32" drill bit for wood stud
wall installation, 1/4" bit for concrete
wall installation, or a 3/8" bit for ceiling
installation.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED

4 5
STEP 2
STEP 1
Plug the power cable into a standard AC wall outlet.
TO LOWER THE SCREEN:
Press the down arrow button on the remote or wall unit. When the screen has reached the desired
height, press the center stop button.
STEP 3
OPTION B: Ceiling Installation
Insert hooks (not included) into drilled holes, and tighten nuts with a wrench until hooks t securely
in place. Carefully hang projector screen on hooks using the pre-installed metal rings.
OPERATION STEPS
TO RAISE THE SCREEN:
Press the up arrow button on the remote or wall unit. When the screen has reached the desired height
or fully retracted, press the center stop button.

6 7
PROGRAMMING
STEP 1
Hold the stop button on the wall control unit for 5 seconds, and two beeps will
sound.
STEP 2
Press any button on the remote to pair the screen with the remote.
STEP 3
Repeat the process for each screen. All programmed screens within range will then
respond to the same remote.
RESETTING
STEP 1
To clear screen remote memory, press and hold the stop button on the wall control
unit until two beeps sound, and continue holding until an additional three beeps
sound.
STEP 2
Press and hold the button again until two beeps sound, and then press any button
on the remote you would like paired with the screen.
TROUBLESHOOTING
REMOTE DOES NOT RESPOND
1. Check if battery is low, and replace if necessary. The remote uses a 23A 12V battery.
2. If changing the battery does not work, reset the wall control unit. Press and hold
the stop button. Two beeps will sound aer 5 seconds; continue holding until three
beeps sound. Press and hold the button again until two beeps sound, and then press
any button on the remote to pair with the wall control.
THE SCREEN DOES NOT RESPOND
1. Make sure the power cable is plugged in, and that the indicator light on the wall
control unit is turned on.
2. Check your circuit breaker to make sure the wall outlet is getting power.
3. If using a power strip or battery backup, make sure the power/reset switch is on.
NOTE: To increase screen life and avoid damage, be sure to retract the screen when not in use.

Last Updated: 12/5/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654