Vivo STAND-V101D User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101d
SKU: STAND-V101D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
a (x1)
Pole
b(x1)
Clamp
c(x1)
Clamp Brace
j (x1)
Support Plate
d(x1)
Swivel Arm
e(x1)
VESA Plate
f (x3)
M5x14
g(x2)
M8x12
h (x1)
Nut
i (x1)
M10
k (x1)
M10 Washer
n1 (x1)
Wire Clip
o(x1)
Allen Key
p (x1)
Wrench
l (x1)
Spring Washer
m (x1)
Grommet
Base Plate
s (x4)
M4 Spacer
q (x4)
M4x12
r (x4)
M4x30
t1 (x1)
So Pad
t2 (x1)
So Pad
n2 (x2)
Wire Clip

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Install the “C” Clamp (b) to the Pole (a) using M5x14
Bolts (f), and tighten using the Allen Key (o). Attach
So Pad (t1) to the “C” Clamp Brace (c). Install the
“C” Clamp (b) to the pole assembly according to
the thickness of the desktop. The thickness can be
changed to three positions. Connect it using M8x12
Bolts (g), and tighten using the Allen Key (o). Tighten
the “C” Clamp (b) to the desktop using the plastic
knob.
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
OPTION B: Existing Grommet Base Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount. Install the Grommet
Base Plate (m) to the Pole (a) using M5x14 Bolts
(f), and tighten using the Allen Key (o). Attach So
Pad (t2) to the Grommet Base Plate (m). Position
the Pole (a) on the mounting surface and secure
using the Support Plate (j), M10 Washer (k), Spring
Washer (l) and M10 Bolt (i). Fasten the M10 Bolt
using provided Wrench (p).
g
o
b
Plastic Knob
a
c
f
Figure 1
Figure 3
t1
Figure 2
j
i
k
l
a
m
f
Figure 4
Figure 6
t2 Figure 5
Drill

4
STEP 1 (Continued)
OPTION C: Self-Drilled Grommet Base Installation
Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm) diameter
hole at the marked position through the mounting surface. Install the Grommet Base Plate (m) to the
Pole (a) using M5x14 Bolts (f), and tighten using the Allen Key (o). Attach So Pad (t2) to the Grommet
Base Plate (m). Position the Pole (a) on the mounting surface and secure using the Support Plate (j),
M10 Washer (k), Spring Washer (l) and M10 Bolt (i). Fasten the M10 Bolt using provided Wrench (p).
STEP 2
Install Swivel Arm (d) to the Pole (a). Fasten the bolt with supplied Allen Key (o). Attach the Wire Clip
(n1,n2) to the Pole (a) and Swivel Arm (d).
j
i
k
l
a
m
f
Figure 7
Figure 9
t2 Figure 8
d
on1
n2

5
STEP 3
OPTION A: Flat Back Monitor
Attach VESA Plate (e) to monitor using bolts (q). Tighten all four bolts using phillips screwdriver.
OPTION B: Curved Back Monitor
Attach VESA Plate (e) to monitor using bolts (r) and spacers (s). Tighten all four bolts using phillips
screwdriver.
q
s
r

6
STEP 5
Tighten the bolt with the supplied Allen Key (o) to fix the tilt angle. Use the supplied Allen Key (o) to
make the necessary adjustments.
STEP 4
Slide the monitor onto the head of Swivel Arm (d). Install the security Nut (h). Make sure the security
nut is installed before you rotate the monitor.
h
o
Fix the tilt angle

7
STEP 6
Store allen keys (o) in wire clips (n1) for future adjustment.

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303