Vivo STAND-V001JB User manual

Monito Des Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model STAND V001JB
Tools Requied
phillips screwdriver
Pacage Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
- -htt s//vivo us.com/ oducts/stand v001jb
A (x1)
Clamp and Pole
B (x1)
Spring Arm
C (x1)
Extension Arm
D (x1)
Plastic Cap
E (x1)
Cable Clip
F (x1)
M6x2 Spring Bolt
G (x1)
3mm Allen Key
H (x1)
mm Allen Key
I (x4)
M4x12 Bolt
J (x4)
M4x30 Bolt
K (x4)
Plastic Spacer

Assembl' Ste s
Ste 1
Loosen the clamp screw on Clamp and Pole (A) until opening is large
enough to fit the edge of the desk. If the pole is loose in the base,
twist the pole clockwise to tighten, then use the 3mm Allen Key (G) to
tighten the set screw on the back of the base to lock the pole.
Ste 2
Place the Pole and Clamp (A) on the edge of the desk and tighten the
clamp screw until securely mounted. If needed, the mm Allen Key
(H) can be used to tighten the clamp screw. If the clamp is unable to
open enough to fit the desk, remove the clamp screw from the base.
Remove the bottom place and re-attach upside down, then re-insert
the clamp screw.
2
Ste 3
Slide the extension arm (C) onto the steel pole (A) until the arm (C)
rests on top of the locating ring.
Ste 4
Adjust the locating ring to required height and tighten to
support the arm.

Ste 6
Carefully place the spring arm (B) with the monitor onto the
extension arm (C), and secure using the M6x2 spring bolt (F) and
Plastic Cap (D).
Ste 7
Use the mm Allen Key (H) to adjust the spring tension inside the arm
(B) depending on the weight of your monitor. NOTE: Turn counter-
clockwise to reduce tension for lighter monitors and clockwise to
increase tension for heavier monitors.
Ste 5
O tion A Flush Monito Suface Installation
Use four M4x12 screws (I) to secure the Spring Arm (B) to the
monitor via mounting holes.
O tion B Recessed Monito Suface Installation
Place four plastic spacers (K) between the Spring Arm (B) and the
monitor, then use four M4x30 screws (J) to secure the Spring Arm (B)
to the monitor via mounting holes.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safet' Waning
Contact us at
Last updated: 0 /18/18
Ste 8
Use the 3mm Allen Key (G) to adjust the arm swivel joints, and the
mm Allen Key (H) to adjust the monitor swivel joint. Turn counter-
clockwise to loosen and clockwise to tighten.
Ste 9
Insert the monitor cables into the
cable covers on the underside of
the arm (B). Leave enough slack
to allow full adjustment and
motion of the arm. Use the cable
clip (E) to fasten cables to the
steel pole (A).
4