Vivo MOUNT-M-FD37B User manual

Flip Down Ceiling TV and Monitor Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-m-fd37b
SKU: MOUNT-M-FD37B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
44lbs
(19.96kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
Drill
Pencil
A (x1)
Mount
B(x1)
4mm Allen Wrench
C(x1)
6mm Allen Wrench
W-A (x4)
Screw
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
M6x12
W-C (x4)
Washer
W-B (x4)
Anchor
M-D (x4)
M8x16
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR CEILING CONSTRUCTION. USE WOOD STUDS
TO MOUNT. We include mounting for concrete ceilings as well. If unsure, please contact us at vivo-us.
com, email at [email protected]om, or call us at 309-278-5303
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
Remove the four bolts from mount (A) with 4mm Allen wrench (B) as shown in diagram. Seprate VESA
plate from mount.
Push arm against ceiling plate of mount (A) to release lock and pull the arm down.
STEP 2
B

4
STEP 3
OPTION A: Wood Beam Ceiling
Hold mount (A) to mounting surface and mark drill holes with pencil. Drill 2.5” (64mm) deep holes
using a 1/8” (3mm) drill bit. Insert screws (W-A) into front two holes, leaving 3mm of thread exposed.
Slide mount onto front two screws. Insert screws (W-A) with washer (W-C) into back two holes. Tighten
all screws. (NOTE: Wood beam must have a width of at least 5” to properly support the mount)
OPTION B: Concrete Ceiling
Hold mount (A) to mounting surface and mark drill holes with pencil. Drill 2.5” (65mm) deep holes
using a 5/16” (8mm) drill bit. Insert anchors (W-B). Insert screws (W-A) into front two holes, leaving
3mm of thread exposed. Slide mount onto front two screws. Insert screws (W-A) with washer (W-C)
into back two holes. Tighten all screws.

5
STEP 4
Mount detached VESA plate to TV with screws (M-A, M-B, M-C, or M-D) depending on your TV’s needs
as shown in diagrams.
STEP 5
Slide TV with VESA plate onto mount (A) and secure with previously removed bolts. Tighten with 4mm
Allen wrench (B).

6
STEP 6
Adjust swivel hinge with 6mm Allen wrench (C). Adjust TV height by loosening bolts with 4mm Allen
wrench (B), then tighten at desired height.
B

7
STEP 7
Push the TV all the way up to the ceiling to engage the lock, securing the TV in the raised position. Push
up again to disengage the lock and lower the TV.
0°/-90°

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303