Vivo STAND-V003T User manual

  
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
 (x1)
Arm
 (x3)
VESA Plate
 (x1)
Monitor Mount
- - !! "#   !
 (x2)
Clamp
$ (x1)
Pole
% (x1)
Pole
& (x1)
Pole Adapter
' (x2)
Cable Clip
( (x1)
Grommet Base
) (x2)
VESA Cap
* (x2)
Small Screw
+ (x )
Rubber Pads
 (x3)
Large Screw
, (x1)
Knob
 (x1)
3mm Allen Wrench
 (x1)
Grommet Plate
- (x1)
4mm Allen Wrench
 (x1)
6mm Allen Wrench
-  (x4)
M8x20
-   (x4)
M6x30
-  (x4)
M x14
-   (x4)
M6x14
- $ (x4)
M8x30
-  % (x4)

#./ 
2
 0
Apply rubber pads (L) to clamp (D) as shown in diagram. Attach
clamp (D) to pole (E) with large screws (M) using 4mm allen wrench
(Q). Secure clamp (D) to desk.
,  12 # (
,  &##  (
Remove crank from clamp (D). Apply rubber pads (L) to grommet
base (I) as shown in diagram. Place on desk. Put grommet plate (N)
on crank. Insert crank through desk and grommet base (I) from
below. Attach and tighten pole (E).
 3
Slide one cable management clip (H) onto pole (E). Slide arm (C)
onto pole (E) and tighten in place using 6mm allen wrench (R). Screw
pole adapter (G) onto pole (E). Screw pole (F) into pole adapter.
Tighten using 3mm Allen wrench (P) as shown in diagram.
 
Slide one cable management clip (H) onto pole (F). Slide monitor
mount (B) onto pole (F) and tighten in place using 6mm allen wrench
(R).

 4
( '  $ 
, '  $ 
Attach VESA plates (A) to monitors using screws (M-A or M-C) and
washers (M-E).
Attach VESA plates (A) to monitors using screws (M-B or M-D),
washers (M-E), and spacers (M-F).
 5
Slide VESA plates (A) with
monitors attached onto monitor
mounts as shown in diagram.
 6
Use VESA caps (J) and small screws (K) to secure bottom two monitors
as shown in diagram. Tighten with 6mm allen wrench (R) as shown in
diagram. Use knob (O) to secure top monitor as shown in diagram.
Tighten with 6mm allen wrench (R) as shown in diagram.
Use cable management clips (H) to manage cables. Use cable
management clips (H) to store allen wrenches.
 7
3

4
8  
If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
9/ :
  
Last updated: 04/30/18