Vivo MOUNT-VW01M User manual

Single Monitor Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-vw01m
SKU: MOUNT-VW01M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED 44lbs
(19.96kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
B(x1)
VESA Plate
C(x2)
M6 Nut
W-A (x3)
ST6.3x55
Screw
M-A (x4)
M4x12
M-B (x4)
M4x14
M-C (x4)
M4x16
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x3)
D6 Washer
W-B (x3)
Concrete
Anchor
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected]om, or call us at 309-278-5303.
D(x1)
Cable Clip
E(x1)
Allen Wrench
F (x1)
Wrench
A (x1)
Mount
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-D (x4)
M5x12
M-E (x4)
M5x14
M-F (x4)
M5x16
M-G (x4)
D5 Washer
M-H (x4)
5mm Spacer

3
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Wall Installation
Use the mount (A) to mark drilling
locations on the wall where a stud is
located. Using a 3/16” bit, drill 2.2” deep
holes into marked locations. Secure the
mount (A) to the wall using ST6.3x55
screws (W-A) with washers (W-C).
OPTION B: Concrete/Brick Wall
Installation
Use the mount (A) to mark drilling
locations on the wall. Using a
3/8” bit, drill 2.4” deep holes into
marked locations. Insert concrete
anchors (W-B) into the holes and
secure the mount (A) to the wall
using ST6.3x55 screws (W-A) with
washers (W-C).

4
STEP 2
Attach the plastic cover to the wall plate of the mount (A).
STEP 3
Attach the cable clip (D) to the arm (A) as shown.

5
STEP 4
OPTION A: For Flat Back Displays
Install the VESA plate (B) to the back of
the TV/monitor using 12/14mm length
bolts (M-A, M-B, M-D or M-E) with D5
washers (M-G).
STEP 5
Partially install one M6 nut (C) to the top screw of the VESA plate (B) and hang
over the slot in the top of the mount (A). Install the second M6 nut, then tighten
both nuts.
OPTION B: For Curved / Recessed
Back Displays
Install the VESA plate (B) to the
back of the TV/monitor using
16mm length bolts (M-C or
M-F) with D5 washers (M-G)
and spacers (M-H).

6
STEP 6
Adjust tilt support using the Allen wrench (E) and swivel joints using the wrench (F).
Organize cables using the cable clip (D).
STEP 7

7
Adjust as Desired

LAST UPDATED:01/06/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303