Vivo STAND-V003T User manual

Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003t
SKU: STAND-V003T
[email protected] www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x3)
VESA Plate
B(x1)
VESA Bracket
C (x1)
Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp
E (x1)
Bottom Pole
F (x1)
Top Pole
G (x1)
Pole Connector
H (x2)
Cable Clip
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x12)
M4x12mm Screw
M-B (x12)
M4x16mm Screw
I (x1)
Grommet Base
J (x2)
VESA Cap
M-C (x12)
M5x12mm Screw
M-G (x12)
Spacer
M-D (x12)
M5x16mm Screw
M-H (x12)
M5 Washer
S-B (x2)
M3x8mm Screw
K (x5)
Rubber Pads
S-A (x3)
M6x16mm Screw
L (x1)
Grommet Plate
S-C (x1)
Thumbscrew
T-A (x1)
3mm Allen Wrench
T-B (x1)
4mm Allen Wrench
T-C (x1)
6mm Allen Wrench
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Remove adhesive backing from Rubber Pads (K) and place them on the underside of Clamp (D).
Assemble Clamp (D) to Bottom Pole (E) using M3x16mm Screws (S-A) and 4mm Allen Wrench (T-A).
Then secure Clamp (D) to the desktop.
OPTION B: Grommet Base Installation
For grommet hole mounting, remove the screw in the top of Hand Bolt (D1) on Clamp (D). Stick Rubber
Pads (K) to bottom of Grommet Base (I). Attach Grommet Plate (L) to Hand Bolt (D1) and run through
grommet hole into Grommet Base (I) and thread into Pole (E).
10-75mm
K
D
E
T-A
S-A
DI
K
L
D1
E

4
STEP 2
Slide Cable Clip (H) and Arm (C) onto Bottom Pole (E). Secure Arm (C) in place using 6mm Allen
Wrench (T-C). Screw Pole Connector (G) onto Bottom Pole (E), then screw Top Pole (F) into Pole
Connector (G). Tighten the set screws in Pole Connector (G) using 3mm Allen Wrench (T-A).
Slide Cable Clip (H) and VESA Bracket (B) onto Top Pole (F). Secure VESA Bracket (B) in place using
6mm Allen Wrench (T-C).
STEP 3
HC
E
T-C
T-A
F
G
E
B
H
T-C
F

5
STEP 4
OPTION A: Flat Back Monitor
Assemble VESA Plates (A) to back of monitors using Screw (M-A or M-C) and M5 Washers (M-H).
OPTION B: Curved Back Monitor
Assemble VESA Plates (A) to back of monitors using Screws (M-B or M-D). If screws are too long,
Spacers (M-G) may be required.
STEP 5
Slide VESA Plates (A) with monitors onto VESA Bracket (B) or Arm (C).
M-A
M-C
M-H
M-H
A
M-B
M-D
M-G
A
A
B
C

6
STEP 6
Secure bottom two monitors to Arm (C) using VESA Caps (J) and M3x8mm Screws (S-B). Tighten with a
Phillips screwdriver. Secure top monitor to VESA Bracket (B) using Thumbscrew (S-C). Use 6mm Allen
Wrench (T-C) to adjust the tilt.
STEP 7
Manage cables using the cable management clips in Arm (C) and Cable Clips (H). Store Allen Wrenches
(T-A, T-B, T-C) in Cable Clip (H) for future adjustments.
P
Q
R
T-C
S-B
J
S-C
T-A
T-B
T-C
B
C
H
C

7
STEP 8
±180°
+45°
-45°
R
+45°
-45°
±180°
+45°
-45°
±180°
T-C
Level bottom monitors by turning VESA Caps (J) using 6mm Allen Wrench (T-C). Adjust monitors as
desired.
J

LAST UPDATED: 06/23/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us.We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oce hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oce hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oce hrs): 5M 4S
309-278-5303