Vivo MOUNT-CAR02 User manual

Car Tablet Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-car02
SKU: MOUNT-CAR02
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
TOOLS NEEDED
5.5lbs
(2.5kg)
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
A(x1)
Base
B(x2)
0° Foot
C(x2)
90° Foot
D(x2)
45° Foot
E (x1)
Pole
F(x1)
Arm
J(x1)
Connecting
Bracket
S-A (x4)
M6x10mm
Screw
S-B (x8)
M6 Washer
S-C (x2)
M6 Nut
S-D (x1)
M6 Flanged Nut
S-E (x1)
M6x45mm
Screw
T-A (x1)
5mm Allen
Wrench
T-B (x1)
Wrench
J(x2)
Screw Cap
G(x4)
Knob
H(x2)
Cable Clips
I(x2)
Support Screw
PACKAGE CONTENTS
Tablet
Mount
Arm
Socket
Wrench
K (x1)
Adapter
S-F (x6)
M4x16 Thumbscrews
S-G (x4)
M4 Washers

3
ASSEMBLY STEPS
STEP 1
Begin by identifying what foot style is needed for your passenger seat configuration, using
the images below. Please note that the two front seat bolts of some vehicles will dier from
each other in angle.
Attach the appropriate foot for the passenger seat’s le bolt [ 0° Foot (B), 90° Foot (C), or
45° Foot (D) ] to the left underside of of Base (A) using M6x10mm Screws (S-A),
M6 Washers (S-B), and a Phillips screwdriver.
0° 90° 45°
B
C
S-A
S-A
S-B
S-B
A
A
AS-B
S-A
0°
90°
45°
D

4
STEP 2
STEP 1 - Continued
Loosely assemble the right foot assembly to Base (A) using M6x10mm Screws (S-A),
M6 Washers (S-B), and a Phillips screwdriver. Align the le foot with the le seat bolt on
the passenger seat. Adjust the right foot to match up with the right bolt on the seat and
tighten M6x10mm Screws (S-A).
A
S-B
S-A
Install compatible Foot (B, C, D) for your passenger seat’s le bolt to the threads on
Connecting Bracket (L) using M6 Nuts (S-C), M6 Washers (S-B), and Wrench (T-B). Please
note, based on your passenger seat’s floor bolts, you may need a dierent foot than what was
used above. T-B
B
C
LL
L
S-C
S-C
S-B
S-B
D
0° 90°
45°
OR
S-C
S-B

5
Loosen the front seat bolts on passenger seat using a socket wrench (size needed depends
on manufacturer).
Slide the le foot under the le seat bolt and the right foot under the right seat bolt.
Adjust the placement as needed and re-tighten bolts.
STEP 3

6
Attach Pole (F) to back of Base (A) using Knobs (I).
STEP 4
A
F
I

7
Thread Support Screws (K) onto Base (A) and place Screw Caps (P) onto the ends once
threaded.
STEP 5
K
P
A

8
STEP 6
1. Slide Arm (G) onto Pole (F) with the adjustment bolt pointing up. Tighten and secure
with 5mm Allen Wrench (T-A). Adjust the arm tension using 5mm Allen Wrench.
2. Determine desired Pole (F) height and Insert M6x45mm Screw (S-J) into slot. Secure
using M6 Flanged Nut (S-I), making sure the flanged, wider part of the nut is faing
outward, with the hex side fitting into the hex indention on Pole (F).
1
2
2
1
1
T-A
T-A
G
F
S-J
S-I
S-I

9
STEP 7
Mount the Adapter (K) to the Arm (F) using the M4x16mm Thumbscrews (S-F) with M4
Washers (S-G) in mounting holes. Loosely install remaining M4x16mm Thumbscrews
(S-F) into the top adjustment holes in Adapter. Place Cable Clips (H) on Arm (F) to
manage cables.
Mounting
Holes
K
F
S-F
S-G
Adjustment
Holes
T-A
T-A
H

10
STEP 8
STEP 8
Note: Before continuing, we recommend checking that your tilt joint on your VESA
mount is tight.
To adjust the Adapter (K) to fit the device, push device down onto springloaded tabs
and position device against the face of the adapter. With the M4x16mm Thumbscrews
(S-F) adjustment screws still loose, center the device on the adapter. Then tighten the
M4x16mm Thumbscrews (S-F) adustment screws.
If assembled mount feels unlevel, tighten Support Screws (I) to level out.
1
2
Device
K
S-F
I