Vivo STAND-SIT2S User manual

Sit-Stand Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit2s
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-SIT2S

2 3
OPTION A: Clamp Installation
Attach base adapter (E) to base of mount arm (A) using screws (I) and 4mm allen wrench (L). For desks
of average thickness: Attach clamp (F) to base adapter (E) using screws (J) and 4mm allen wrench (L)
as shown in diagram. For thicker desks: Attach clamp (F) to base adapter (E) using screws (J) and 4mm
allen wrench (L) as shown in diagram. Attach cable management clip (G) to base adapter (E). Tighten
clamp (F) to desk.
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Mount Arm
B(x1)
Pole
C(x1)
Tray
J (x4)
M6x10
D(x1)
Monitor Arm
E(x1)
Base Adapter
F (x1)
Clamp
G(x1)
Cable Clip
H (x2)
M8x100
I (x4)
M6x20
M-B (x8)
M4x16
M-D (x8)
M5x16
M-C (x8)
M5x12
O (x2)
Grommet
Plate
K (x2)
M8x24
N (x1)
Metal Plate
P (x2)
Spring Washer
Q (x2)
Nut
R (x1)
Wrench
L (x1)
4mm Allen
Wrench
M (x1)
6mm Allen
Wrench
M-A (x8)
M4x12
M-E (x8)
D5 Washer
M-F (x8)
Spacer
TOOLS NEEDED
Phillips
Screwdriver
13.2 lbs
(6 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 4.4 lbs
(2 kg)
PER ARM TRAY
ASSEMBLY STEPS
STEP 1
E
L
I
F
J
L
10-55mm
F
J
L
40-92mm
G
H
LNI
H
LNI
O
PQ
R
10-80mm
OPTION B: Grommet Installation
Attach metal plate (N) to base of mount arm
(A) using screws (H, I) with 4mm allen wrench
(L). Attach grommet plates (O) to screws (H)
using nuts (Q), washers (P), and wrench (R).
Tighten.

4 5
STEP 2
Attach monitor arm (D) using previously removed bracket and screws, making sure adjustment screws
on monitor brackets are facing up. Tighten with 4mm Allen wrench (L).
STEP 4
For at back monitors, attach VESA plates using 12mm screws (M-A or M-B) with washers
(M-E). For curved or recessed back monitors, use 16mm screws (M-C or M-D) with
washers (M-E) and spacers (M-F).
STEP 6
Remove knobs and slide VESA plates o from brackets. Set parts aside for later use.
STEP 5
Slide VESA plates with monitors onto mounting
brackets of arm (D) and secure with previously
removed knobs.
STEP 7
Adjust gas spring strength using 6mm Allen wrench (M). Turning clockwise will decrease strength, and
counter-clockwise will increase strength.
STEP 8
STEP 3
Remove two lower screws from back
of pole (B) and set aside. Attach tray
(C) to pole using M8x24 bolts (K),
and tighten with 6mm Allen wrench
(M). Remove front bracket from arm
mount at top of pole using 4mm Allen
wrench (L) as shown. Set parts aside.
Loosen top two screws on back of pole (B) until 5mm of thread is exposed on each. Slide pole onto
mount of arm (A). Attach with previously removed screws, and tighten all screws with 4mm Allen
wrench (L).
M
L
K
L
L
5m m
L
L
1 2 3
TV
TV
TV
TV
M- F
M
NOTE: Tighten socket set
screw if the joint makes a
popping noise.

6 7
STEP 9
Adjust height of monitors using knob on back of pole
(B). Correct individual monitor height by turning the
knob on each monitor bracket as shown. Use 6mm
Allen wrench (M) if knobs are too sti to turn by hand.
Adjust rotation of tray (C) using 4mm Allen wrench (L) as
shown if tray is not level.
STEP 10
To adjust tray to 10° tilt angle, rst ip the tray up fully, then turn the supports in front of the hinge
upward. Set the keyboard tray back down. Allen wrenches (L, M) can be stored underneath the
keyboard tray as shown.
STEP 11
Use a screwdriver to remove screws securing the cable covers.
STEP 12
Insert cables making sure there is enough slack for full movement, then re-install covers.
Adjust as Desired
M
M
+15°
-15°
L
+4°
-4°
0°
10° 10 °
1
2
1
2
2
1
1
2
360°
+15°
-15°
180°
360°
360°

Last Updated: 12/14/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654