Vivo STAND-TV75BH User manual

Black Corner TV Stand with Dark Walnut Shelves
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv75bh
SKU: STAND-TV75BH
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot
be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate
use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
22lbs
(10 kg)
Shelf
88 lbs
(40 kg)
TV
A (x1)
Right Back Leg
E (x1)
Large Shelf
F (x1)
Small Shelf
G (x1)
VESA Plate
H (x1)
Le VESA
Bracket
I (x1)
Right VESA
Bracket
J (x4)
Cable Clips
K (x1)
Le Shelf
Bracket
S-A (x2)
M6x60mm
Screw
S-F (x4)
M8 Screw Cap
M-A (x4)
M6x14mm
Screw
M-F (x4)
Small Spacer
M-E (x4)
M8 Washer
M-G (x4)
Large Spacer
T-A (x1)
Bubble Level
T-B (x1)
4mm Allen Wrench
T-C (x1)
5mm Allen Wrench
T-D (x1)
Wrench
M-B (x4)
M8x16mm
Screw
M-C (x4)
M6x30mm
Screw
M-D (x4)
M8x35mm
Screw
S-B (x4)
M8x55mm
Screw
S-C (x18)
M6x12mm
Screw
S-D (x8)
M8 Washer
S-E (x4)
M8 Nut
L (x1)
Right Shelf
Bracket
M (x2)
Shelf Clip
N (x2)
Shelf Spacer
B (x1)
Le Back Leg
C (x1)
Upper Support
D (x1)
Front Leg

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM
TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY
ON ANY PART OF TV OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT
ELIMINATE RISK OF TIPOVER.
STEP 1
STEP 2
Connect Front Leg (D) to Right Back Leg (A) and Le Back Leg (B) using M6x12mm Screws (S-C) with
4mm Allen Wrench (T-B).
NOTE: Do not fully install screws; they will be fully tightened in a later step.
Slide Upper Support (C) on to leg assembly, making sure to match up the holes with Right Back
Leg (A) and Le Back Leg (B). Secure using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-B).
NOTE: Do not fully install screws; they will be fully tightened in a later step.
A
S-C
T-B
B
D
C
A
B
S-C
T-B

4
STEP 3
Install Shelf Clips (M) to underside of Large Shelf (E) at a 45° angle facing inward, using M6x12mm
Screws (S-C) and 4mm Allen Wrench (T-B). Insert Shelf Spacers (N) into the ends of Large Shelf (E).
Snap shelf assembly to the raised curves of assembled base as shown below.
Secure Large Shelf (E) to frame assembly using M6x60mm Screws (S-A)
and 4mm Allen Wrench (T-B). Use 4mm Allen Wrench (T-B) to fully
secure and tighten previously installed screws.
MM
N
E
T-B
S-CS-C
INSTALL AT 45° ANGLE
T-B
S-A E

5
Insert two M6x12mm Screws (S-C) into the bottom inner holes on the frame assembly as show below,
using 4mm Allen Wrench (T-B), making sure to leave 5mm of threads exposed. Place shelf assembly
over installed screws.
T-B
L
K
F
S-C
T-B
> 5mm
S-C
Secure shelf assembly to the frame using M6x12mm Screws (S-C) in the remaining inner holes with
4mm Allen Wrench (T-B). Tighten all previously installed M6x12mm Screws (S-C) on the small shelf
assembly using 4mm Allen Wrench (T-B).
T-B
S-C
STEP 4
Assemble Le Shelf Bracket (K) and Right Shelf Bracket (L) to Small Shelf (F) using M6x12mm Screws
(S-C) and 4mm Allen Wrench (T-B). NOTE: Do not overtighten screws.

6
STEP 5
Assemble Le VESA Bracket (H) and Right VESA Bracket (I) to back of TV using appropriate Screws
(M-A thru M-D), M8 Washers (M-E), Spacers (M-F, M-G) and a Phllips screwdriver.
STEP 6
Place Bubble Level (T-A) on VESA Plate (G). Assemble VESA Plate (G) to Upper Support (C) in one of two
postions as shown below using M8x55mm Screws (S-B), M8 Washers (S-D), M8 Nuts (S-E) and M8 Screw
Caps (S-F). Secure using 5mm Allen Wrench (T-C) and Wrench (T-D).
T-C S-B
S-D
S-E S-F
T-D
S-DS-D
G
T-A
C

7
G
STEP 7
STEP 8
Loosen the safety screws on Le VESA Bracket (H) and Right VESA Bracket
(I) with a Phillips screwdriver, then place onto VESA Plate (G), as shown
below. Retighten safety screws with a Phillips screwdriver once in place.
Secure Cable Clips (J) to the frame assembly and manage cables. Adjust the tilt as desired.
II
HH
J

LAST UPDATED: 02/08/2023
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303