Vivo STAND-V011H User manual

Single Monitor Extra Tall Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v011h
SKU: STAND-V011H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
VESA Plate
B(x1)
Bracket
C(x1)
Base
S-A (x1)
Thumbscrew
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Lower Pole
E(x1)
Middle Pole
F (x1)
Upper Pole
G (x3)
Cable Clip
S-B (x3)
M6x12mm Screw
M-A (x4)
M4x12mm Screw
M-B (x4)
M4x16mm Screw
M-C (x4)
M5x12mm Screw
M-D (x4)
M5x16mm Screw
M-E (x4)
M5 Washer
M-F (x4)
Spacer
T-A (x1)
4mm Allen Wrench
T-B (x1)
6mm Allen Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED 17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Secure Lower Pole (D) to Base (C) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A). Slide
one Cable Clip (G) onto Lower Pole (D).
Lower Pole (D) & Upper Pole (F) may look similar. To dierentiate,
match the hole pattern to images below. The holes on Lower Pole (D)
are spaced closer together than Upper Pole (F).
Lower Pole Upper Pole
D
G
C
S-B
T-A

4
STEP 2
STEP 3
Thread and secure Middle Pole (E) onto Lower Pole (D) and slide one Cable Clip (G) on. Thread Upper
Pole (F) onto Middle Pole (E) and place the remaining Cable Clip (G) onto pole.
G
G
B
T-B
F
E
D
Slide Bracket (B) onto pole assembly and tighten in desired location with 6mm Allen Wrench (T-B).

5
STEP 4
STEP 5
Install VESA Plate (A) onto monitor using appropriate Screws (M-A thru M-D), M5 Washer (M-E), and a
Phillips screwdriver. If needed, Spacers (M-F) can be used.
OR
M-A
M-C
M-E
M-B
M-D A
A
M-E
M-F
Place monitor with VESA plate onto Bracket (B). Secure with Thumbscrew (S-A).
B
S-A

6
STEP 7
STEP 6
Use Cable Clips (G) to route and manage cables.
To adjust tilt of monitor, loosen side screw on Bracket (B) using 6mm Allen Wrench (T-B).
B
T-B
G

7
STEP 8
Adjust as Desired
Allen Wrenches (T-A, T-B) can be stored in lower Cable Clip (G).
T-B
T-A
G

LAST UPDATED: 01/16/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303