Vivo STAND-TV70B User manual

Black V-Base Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv70b
SKU: STAND-TV70B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Leg
B(x1)
Pole
C(x2)
Foot
I (x2)
Security Cable
Clamp
J x4)
M8x12
K(x4)
M6x15
H(x2)
Security
Clip
D (x1)
Upper VESA
Bracket
E (x1)
Lower VESA
Bracket
F (x2)
Foot Pad
G (x1)
Steel Cable
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
M-F (x4)
Square
Washer
M-G (x8)
5mm Spacer
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-D (x4)
M8x30
M-H (x8)
15mm Spacer
M-C (x4)
M6x30
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
N (x1)
4mm Allen
Wrench
O x1)
5mm Allen
Wrench
M(x1)
2mm Allen
Wrench
L (x2)
Cable Cover
P(x4)
ST4.8*38 Screw
Q (x4)
Anchor

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 2
88lbs
(40kg)
Slide the feet (C) onto the base of the leg (A). Insert M8x12 bolts (J) into the bottom holes of
the feet, and M6x15 bolts (K) through the base into the rear holes of the feet. Tighten with
the 5mm Allen wrench (O). Screw the foot pads (F) into the base, and adjust foot pads to sit
level on the floor.
Screw the pole (B) onto the leg (A). Loosen the set screws in the collar using the
4mm Allen wrench (N), and adjust the collar height to the recommended position
below the top of the pole based on your TV’s VESA mounting hole pattern. Tighten
the set screws, making sure they face towards the back of the stand.
Tape
Measure
Pliers
A- VESA Height = 200mm: 4” - 6.7” (90-110mm)
B- VESA Height = 300mm: 3.5” - 4.3” (100-170mm)
C- VESA Height = 400mm: 2” - 2.75” (50-70mm)

4
STEP 3
Remove the screw from the lower VESA bracket (E) to separate into parts E1 and
E2, and open the clamp.
STEP 4
OPTION A: Flat Back TV
Position VESA brackets horizontally on the back of the
TV, making sure the upper bracket (D) is on top and the
lower bracket (E2) is below. Secure using screws (M-A or
M-B) with square washers (M-F), with security clips (H)
installed to the top holes.
OPTION B: Curved Back TV
Position VESA brackets horizontally on the back of the TV,
making sure the upper bracket (D) is on top and the lower
bracket (E2) is below. Secure using screws (M-C, M-D or
M-E) with square washers (M-F) and spacers (M-G, M-H),
with security clips (H) installed to the top holes.

5
STEP 5
Slide the TV with VESA brackets (D, E2) onto the pole (B). Close the clamp on the
lower VESA bracket over the pole and secure with previously removed screw (E1).
STEP 6
Route cables through the cables holes in the leg (A). Install cable covers (L) to the
cables holes, using pliers to break out sections for x2 or x3 cables if needed.

6
STEP 7
OPTION A: Wood Wall Installation
Using security cable clamps (I) as guides, mark drilling locations on the wall. Use
of a stud finder is recommended. Drill holes at least 1.6” (40mm) deep using a 1/8”
(3.5mm) drill bit. Mount clamps to the wall using 1-1/4” screws (P). Thread steel
cable (G) through the security clips on the TV and center holes in the cable clamps
as shown, then tighten clamps using the 2mm Allen wrench (M).

7
STEP 7 (Continued)
OPTION B: Concrete/Brick Wall Installation
Using security cable clamps (I) as guides, mark drilling locations on the wall. Drill
holes at least 1.6” (40mm) deep using a 9/32” (7mm) drill bit. Insert anchors (Q)
into the holes and mount clamps to the wall using 1-1/4” screws (P). Thread steel
cable (G) through the security clips on the TV and center holes in the cable clamps
as shown, then tighten clamps using the 2mm Allen wrench (M).

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303