Vivo STAND-V101A User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101a
SKU: STAND-V101A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
a (x1)
Pole
b(x1)
Clamp
c(x1)
Clamp Brace
j (x1)
Support Plate
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
d(x1)
Monitor Arm
e(x1)
VESA Plate
f (x3)
M5x14
g(x2)
M8x12
h (x1)
M4x6
i (x1)
M10
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
k (x1)
M10 Washer
n (x1)
Wire Clip
o(x1)
Allen Key
p (x1)
Wrench
l (x1)
Spring Washer
m (x1)
Grommet
Base Plate
s (x4)
M4 Spacer
q (x4)
M4x12
r (x4)
M4x30
t1 (x1)
So Pad
t2 (x1)
So Pad

3
ASSEMBLY STEPS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
OPTION A: Clamp Installation
1. Install the clamp brace (c) to the pole (a) using
M5x14 bolts (f) as shown in Figure 1.
2. Attach so pad (t1) to the clamp brace as shown in
Figure 2.
3. Install the clamp (b) to one of three positions on
the pole assembly according to the thickness of
the desktop. Connect using M8x12 bolts (g) and
tighten using the 5mm Allen key (o-5), then tighten
the clamp to the desktop using the plastic knob as
shown in Figure 3.
OPTION B: Grommet Base Installation
If an existing grommet hole comes with a plastic
protector, remove it to ensure a flat mounting surface
before installing the desk mount.
1. Install the grommet base plate (m) to the pole (a)
using M5x14 bolts (f) as shown in Figure 4.
2. Attach so pad (t2) to the grommet base plate as
shown in Figure 5.
3. Position the pole assembly on the mounting
surface and secure using the support plate (j),
M10 washer (k), spring washer (l) and M10 bolt (i)
as shown in Figure 6. Tighten using the provided
wrench (p).
g
o
b
Plastic Knob
c
f
Figure 1
Figure 3
t1
Figure 2
j
i
k
l
a
m
f
Figure 4
Figure 6
t2 Figure 5
Drill

4
STEP 1 (Continued)
OPTION C: Grommet Base Installation
Self Drilled Grommet Installation
If no grommet hole is present, drill a ⅜” (10mm) hole
through the mounting surface.
1. Install the grommet base plate (m) to the pole
(a) using M5x14 bolts (f) as shown in Figure 7.
2. Attach so pad (t2) to the grommet base plate
as shown in Figure 8.
3. Position the pole assembly on the mounting
surface and secure using the support plate
(j), M10 washer (k), spring washer (l) and M10
bolt (i) as shown in Figure 9. Tighten using the
provided wrench (p).
STEP 2
Slide the monitor arm (d) onto the pole (a), then tighten the bolt with the 6mm Allen key (o-6). Attach
the wire clip (n) to the pole.
j
i
k
l
a
m
f
Figure 7
Figure 9
t2 Figure 8
d
o
n

5
STEP 3
OPTION A: Flat Back Monitor
For a monitor with a flat back, use M4x12 thumbscrews (q) to attach the VESA plate (e) to the monitor.
NOTE: Do not over-tighten screws. Thumbscrews only need to be finger-tight.
OPTION B: Curved Back Monitor
For a monitor with a curved or recessed back, use spacers (s) and M4x30 bolts (r) to attach the VESA
plate (e) to the monitor. NOTE: Do not over-tighten screws.
q
s
r

6
STEP 4
Slide the monitor onto the head of monitor arm (d) as shown. Install the M4x6 bolt (h) to secure the
monitor. Make sure the bolt is installed before you rotate the monitor.
h

7
STEP 5
Fasten the grub screw in the monitor arm to fix the tilt and using the 3mm Allen key (o-3). Alternatively,
remove the VESA plate and tighten the nut in the center of the joint. Manage the wires using the cable
clip (n) as shown.
grub
screw

LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303